when we clip a motor output we need to decrease the opposite motor by
the same amount, otherwise we lose the ability to control the quad
when the servo outputs are extreme
Found using the quad HIL test. Thanks to Jani for testing this on a
real quad!
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2929 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added rate of change limit for noisy Sonars.
converted to static functions - Tridge
New Throttle PIDs from Jack
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2904 f9c3cf11-9bcb-44bc-f272-b75c42450872
we don't send MSG_LOCATION in HIL mode during GPS updates, as we don't
call the GPS update routines, so we need to send MSG_LOCATION as part
of the Position stream
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2892 f9c3cf11-9bcb-44bc-f272-b75c42450872
defaults for these are already in config.h, but protected with #ifndef
wrappers. The #ifndef wrappers are useful to allow users to have
makefile targets for different configs, so you can (for example), do
"make heli" with a local makefile
This makes it easier for developers to ensure that all configs build
correctly
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2890 f9c3cf11-9bcb-44bc-f272-b75c42450872
this makes most of the variables and functions in the main
ArduCopterMega.pde code static, which allows the compiler to optimise
better, and exposes unused variables as compiler warnings
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2888 f9c3cf11-9bcb-44bc-f272-b75c42450872
this saves a little bit of code by moving the calculation of the
default log bitmask to compile time from runtime
(merge from APM)
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2887 f9c3cf11-9bcb-44bc-f272-b75c42450872
set LOGGING_ENABLED to DISABLED to disable all logging. This saves
about 10k of flash when disabled.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2886 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added Yaw control when descending in Alt hold
lowered kP & kD for Alt hold a tad
Adjusted RTL behavior to do speed control up to 4m to home, then go into Loiter
Fixed issue with AUTO not getting proper input.
Added Limit to high side of motors
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2874 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added Yaw control when descending in Alt hold
lowered kP & kD for Alt hold a tad
Adjusted RTL behavior to do speed control up to 4m to home, then go into Loiter
Fixed issue with AUTO not getting proper input.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2873 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added Yaw control when descending in Alt hold
lowered kP & kD for Alt hold a tad
Adjusted RTL behavior to do speed control up to 4m to home, then go into Loiter
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2872 f9c3cf11-9bcb-44bc-f272-b75c42450872
this allows you to create a local makefile like this:
include Makefile
hil:
make -f Makefile EXTRAFLAGS="-DHIL_MODE=HIL_MODE_ATTITUDE -DSERIAL3_BAUD=115200"
and then use 'make hil'
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2843 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added camera reversing parameters in AP_Var
Added RTL Throttle Hold set/check
Added dynamic speed control to slow down as you reach waypoints and RTL Home
upped Yaw Dead zone slightly.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2841 f9c3cf11-9bcb-44bc-f272-b75c42450872
Before: -> After
Stabilize P –> Stabilize P (Use NG values, or 8.3 x the older AC2 value)
Stabilize I –> Stabilize I (Stays same value)
Stabilize D –> Rate P (Stays same value)
–> Rate I (new)
Added a new value – an I term for rate. The old stabilization routines did not use this term. Please refer to the config.h file to read more about the new PIDs.
Added framework for using DCM corrected Accelerometer rates. Code is commented out for now.
Added set home at Arming.
Crosstrack is now a full PID loop, rather than just a P gain for more control.
Throttle now slews when switching out of Alt hold or Auto modes for less jarring transitions
Sonar and Baro PIDs are now combined into a throttle PID Yaw control is completely re-written.
Added Octa_Quad support - Max
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2836 f9c3cf11-9bcb-44bc-f272-b75c42450872
we were looking for the wrong regA value
Thanks to Chris for the debugging help! (and happy birthday!)
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2828 f9c3cf11-9bcb-44bc-f272-b75c42450872
this adds error checking to all operations on the compass, to ensure
that we don't accept invalid data
This also fixes the calibration values for the 5883L to match the
recommended values in the spec
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2815 f9c3cf11-9bcb-44bc-f272-b75c42450872
Slighted tuned down D term in Loiter PIDs after testing, tuned up P slightly
fixed alt hold bug cause when gaining 3D lock in alt hold.
Mavlink now reports correct throttle scaling value in mavlink
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2746 f9c3cf11-9bcb-44bc-f272-b75c42450872
Slighted tuned down D term in Loiter PIDs after testing, tuned up P slightly
fixed alt hold bug cause when gaining 3D lock in alt hold.
Mavlink now reports correct throttle scaling value in mavlink
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2745 f9c3cf11-9bcb-44bc-f272-b75c42450872
rmackay9@yahoo.com
tridge60@gmail.com
jasonshort
mich146@hotmail.com
jphelirc
deweibel@gmail.com