ardupilot/libraries/AC_AttitudeControl/AC_AttitudeControl_Multi.cpp

234 lines
9.6 KiB
C++
Raw Normal View History

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: t -*-
#include "AC_AttitudeControl_Multi.h"
#include <AP_HAL/AP_HAL.h>
#include <AP_Math/AP_Math.h>
2016-02-15 02:25:41 -04:00
// table of user settable parameters
const AP_Param::GroupInfo AC_AttitudeControl_Multi::var_info[] = {
// parameters from parent vehicle
AP_NESTEDGROUPINFO(AC_AttitudeControl, 0),
// @Param: RAT_RLL_P
// @DisplayName: Roll axis rate controller P gain
// @Description: Roll axis rate controller P gain. Converts the difference between desired roll rate and actual roll rate into a motor speed output
// @Range: 0.08 0.30
// @Increment: 0.005
// @User: Standard
// @Param: RAT_RLL_I
// @DisplayName: Roll axis rate controller I gain
// @Description: Roll axis rate controller I gain. Corrects long-term difference in desired roll rate vs actual roll rate
// @Range: 0.01 0.5
// @Increment: 0.01
// @User: Standard
// @Param: RAT_RLL_IMAX
// @DisplayName: Roll axis rate controller I gain maximum
// @Description: Roll axis rate controller I gain maximum. Constrains the maximum motor output that the I gain will output
// @Range: 0 1
// @Increment: 0.01
// @Units: Percent
2016-02-15 02:25:41 -04:00
// @User: Standard
// @Param: RAT_RLL_D
// @DisplayName: Roll axis rate controller D gain
// @Description: Roll axis rate controller D gain. Compensates for short-term change in desired roll rate vs actual roll rate
// @Range: 0.0 0.02
2016-02-15 02:25:41 -04:00
// @Increment: 0.001
// @User: Standard
// @Param: RAT_RLL_FILT
// @DisplayName: Roll axis rate conroller input frequency in Hz
// @Description: Roll axis rate conroller input frequency in Hz
// @Range: 1 100
// @Increment: 1
// @Units: Hz
2016-02-15 02:25:41 -04:00
AP_SUBGROUPINFO(_pid_rate_roll, "RAT_RLL_", 1, AC_AttitudeControl_Multi, AC_PID),
// @Param: RAT_PIT_P
// @DisplayName: Pitch axis rate controller P gain
// @Description: Pitch axis rate controller P gain. Converts the difference between desired pitch rate and actual pitch rate into a motor speed output
// @Range: 0.08 0.30
// @Increment: 0.005
// @User: Standard
// @Param: RAT_PIT_I
// @DisplayName: Pitch axis rate controller I gain
// @Description: Pitch axis rate controller I gain. Corrects long-term difference in desired pitch rate vs actual pitch rate
// @Range: 0.01 0.5
// @Increment: 0.01
// @User: Standard
// @Param: RAT_PIT_IMAX
// @DisplayName: Pitch axis rate controller I gain maximum
// @Description: Pitch axis rate controller I gain maximum. Constrains the maximum motor output that the I gain will output
// @Range: 0 1
// @Increment: 0.01
// @Units: Percent
2016-02-15 02:25:41 -04:00
// @User: Standard
// @Param: RAT_PIT_D
// @DisplayName: Pitch axis rate controller D gain
// @Description: Pitch axis rate controller D gain. Compensates for short-term change in desired pitch rate vs actual pitch rate
// @Range: 0.0 0.02
2016-02-15 02:25:41 -04:00
// @Increment: 0.001
// @User: Standard
// @Param: RAT_PIT_FILT
// @DisplayName: Pitch axis rate conroller input frequency in Hz
// @Description: Pitch axis rate conroller input frequency in Hz
// @Range: 1 100
// @Increment: 1
// @Units: Hz
2016-02-15 02:25:41 -04:00
AP_SUBGROUPINFO(_pid_rate_pitch, "RAT_PIT_", 2, AC_AttitudeControl_Multi, AC_PID),
// @Param: RAT_YAW_P
// @DisplayName: Yaw axis rate controller P gain
// @Description: Yaw axis rate controller P gain. Converts the difference between desired yaw rate and actual yaw rate into a motor speed output
// @Range: 0.10 0.50
2016-02-15 02:25:41 -04:00
// @Increment: 0.005
// @User: Standard
// @Param: RAT_YAW_I
// @DisplayName: Yaw axis rate controller I gain
// @Description: Yaw axis rate controller I gain. Corrects long-term difference in desired yaw rate vs actual yaw rate
// @Range: 0.010 0.05
// @Increment: 0.01
// @User: Standard
// @Param: RAT_YAW_IMAX
// @DisplayName: Yaw axis rate controller I gain maximum
// @Description: Yaw axis rate controller I gain maximum. Constrains the maximum motor output that the I gain will output
// @Range: 0 1
// @Increment: 0.01
// @Units: Percent
2016-02-15 02:25:41 -04:00
// @User: Standard
// @Param: RAT_YAW_D
// @DisplayName: Yaw axis rate controller D gain
// @Description: Yaw axis rate controller D gain. Compensates for short-term change in desired yaw rate vs actual yaw rate
// @Range: 0.000 0.02
// @Increment: 0.001
// @User: Standard
// @Param: RAT_YAW_FILT
// @DisplayName: Yaw axis rate conroller input frequency in Hz
// @Description: Yaw axis rate conroller input frequency in Hz
// @Range: 1 100
// @Increment: 1
// @Units: Hz
2016-02-15 02:25:41 -04:00
AP_SUBGROUPINFO(_pid_rate_yaw, "RAT_YAW_", 3, AC_AttitudeControl_Multi, AC_PID),
// @Param: THR_MIX_MIN
// @DisplayName: Throttle Mix Minimum
// @Description: Throttle vs attitude control prioritisation used when landing (higher values mean we prioritise attitude control over throttle)
// @Range: 0.1 0.25
// @User: Advanced
AP_GROUPINFO("THR_MIX_MIN", 4, AC_AttitudeControl_Multi, _thr_mix_min, AC_ATTITUDE_CONTROL_MIN_DEFAULT),
// @Param: THR_MIX_MAX
// @DisplayName: Throttle Mix Maximum
// @Description: Throttle vs attitude control prioritisation used during active flight (higher values mean we prioritise attitude control over throttle)
// @Range: 0.5 0.9
// @User: Advanced
AP_GROUPINFO("THR_MIX_MAX", 5, AC_AttitudeControl_Multi, _thr_mix_max, AC_ATTITUDE_CONTROL_MAX_DEFAULT),
2016-02-15 02:25:41 -04:00
AP_GROUPEND
};
AC_AttitudeControl_Multi::AC_AttitudeControl_Multi(AP_AHRS &ahrs, const AP_Vehicle::MultiCopter &aparm, AP_MotorsMulticopter& motors, float dt) :
AC_AttitudeControl(ahrs, aparm, motors, dt),
_motors_multi(motors),
_pid_rate_roll(AC_ATC_MULTI_RATE_RP_P, AC_ATC_MULTI_RATE_RP_I, AC_ATC_MULTI_RATE_RP_D, AC_ATC_MULTI_RATE_RP_IMAX, AC_ATC_MULTI_RATE_RP_FILT_HZ, dt),
_pid_rate_pitch(AC_ATC_MULTI_RATE_RP_P, AC_ATC_MULTI_RATE_RP_I, AC_ATC_MULTI_RATE_RP_D, AC_ATC_MULTI_RATE_RP_IMAX, AC_ATC_MULTI_RATE_RP_FILT_HZ, dt),
_pid_rate_yaw(AC_ATC_MULTI_RATE_YAW_P, AC_ATC_MULTI_RATE_YAW_I, AC_ATC_MULTI_RATE_YAW_D, AC_ATC_MULTI_RATE_YAW_IMAX, AC_ATC_MULTI_RATE_YAW_FILT_HZ, dt)
{
AP_Param::setup_object_defaults(this, var_info);
}
// Update Alt_Hold angle maximum
void AC_AttitudeControl_Multi::update_althold_lean_angle_max(float throttle_in)
{
// calc maximum tilt angle based on throttle
float thr_max = _motors_multi.get_throttle_thrust_max();
// divide by zero check
if (is_zero(thr_max)) {
_althold_lean_angle_max = 0.0f;
return;
}
float althold_lean_angle_max = acos(constrain_float(_throttle_in/(AC_ATTITUDE_CONTROL_ANGLE_LIMIT_THROTTLE_MAX * thr_max), 0.0f, 1.0f));
_althold_lean_angle_max = _althold_lean_angle_max + (_dt/(_dt+_angle_limit_tc))*(althold_lean_angle_max-_althold_lean_angle_max);
}
void AC_AttitudeControl_Multi::set_throttle_out(float throttle_in, bool apply_angle_boost, float filter_cutoff)
{
_throttle_in = throttle_in;
update_althold_lean_angle_max(throttle_in);
_motors.set_throttle_filter_cutoff(filter_cutoff);
if (apply_angle_boost) {
// Apply angle boost
throttle_in = get_throttle_boosted(throttle_in);
}else{
// Clear angle_boost for logging purposes
_angle_boost = 0.0f;
}
_motors.set_throttle(throttle_in);
_motors.set_throttle_avg_max(get_throttle_avg_max(MAX(throttle_in, _throttle_in)));
}
// returns a throttle including compensation for roll/pitch angle
// throttle value should be 0 ~ 1
float AC_AttitudeControl_Multi::get_throttle_boosted(float throttle_in)
{
if (!_angle_boost_enabled) {
_angle_boost = 0;
return throttle_in;
}
// inverted_factor is 1 for tilt angles below 60 degrees
// inverted_factor reduces from 1 to 0 for tilt angles between 60 and 90 degrees
float cos_tilt = _ahrs.cos_pitch() * _ahrs.cos_roll();
float inverted_factor = constrain_float(2.0f*cos_tilt, 0.0f, 1.0f);
float boost_factor = 1.0f/constrain_float(cos_tilt, 0.5f, 1.0f);
float throttle_out = throttle_in*inverted_factor*boost_factor;
_angle_boost = constrain_float(throttle_out - throttle_in,-1.0f,1.0f);
return throttle_out;
}
// returns a throttle including compensation for roll/pitch angle
// throttle value should be 0 ~ 1
float AC_AttitudeControl_Multi::get_throttle_avg_max(float throttle_in)
{
return MAX(throttle_in, throttle_in*MAX(0.0f,1.0f-_throttle_rpy_mix)+_motors.get_throttle_hover()*_throttle_rpy_mix);
}
// update_throttle_rpy_mix - slew set_throttle_rpy_mix to requested value
void AC_AttitudeControl_Multi::update_throttle_rpy_mix()
{
// slew _throttle_rpy_mix to _throttle_rpy_mix_desired
if (_throttle_rpy_mix < _throttle_rpy_mix_desired) {
// increase quickly (i.e. from 0.1 to 0.9 in 0.4 seconds)
_throttle_rpy_mix += MIN(2.0f*_dt, _throttle_rpy_mix_desired-_throttle_rpy_mix);
} else if (_throttle_rpy_mix > _throttle_rpy_mix_desired) {
// reduce more slowly (from 0.9 to 0.1 in 1.6 seconds)
_throttle_rpy_mix -= MIN(0.5f*_dt, _throttle_rpy_mix-_throttle_rpy_mix_desired);
}
_throttle_rpy_mix = constrain_float(_throttle_rpy_mix, 0.1f, 1.0f);
}
void AC_AttitudeControl_Multi::rate_controller_run()
{
// move throttle vs attitude mixing towards desired (called from here because this is conveniently called on every iteration)
update_throttle_rpy_mix();
_motors.set_roll(rate_bf_to_motor_roll(_ang_vel_target_rads.x));
_motors.set_pitch(rate_bf_to_motor_pitch(_ang_vel_target_rads.y));
_motors.set_yaw(rate_bf_to_motor_yaw(_ang_vel_target_rads.z));
control_monitor_update();
}