ardupilot/libraries/AP_HAL_ChibiOS/hwdef/Sierra-TrueNavIC/hwdef.dat

Ignoring revisions in .git-blame-ignore-revs. Click here to bypass and see the normal blame view.

121 lines
2.7 KiB
Plaintext
Raw Normal View History

2024-01-20 00:15:06 -04:00
# HW definition file for Sierra-TrueNavIC
# MCU class and specific type
MCU STM32L431 STM32L431xx
# bootloader starts firmware at 36k + 4k (STORAGE_FLASH)
FLASH_RESERVE_START_KB 40
FLASH_SIZE_KB 256
# store parameters in pages 18 and 19
STORAGE_FLASH_PAGE 18
define HAL_STORAGE_SIZE 800
# ChibiOS system timer
STM32_ST_USE_TIMER 15
define CH_CFG_ST_RESOLUTION 16
# board ID for firmware load
APJ_BOARD_ID 5302
# crystal frequency
OSCILLATOR_HZ 16000000
env AP_PERIPH 1
define HAL_NO_GPIO_IRQ
define SERIAL_BUFFERS_SIZE 512
define PORT_INT_REQUIRED_STACK 64
define DMA_RESERVE_SIZE 0
# MAIN_STACK is stack for ISR handlers
MAIN_STACK 0x300
# PROCESS_STACK controls stack for main thread
PROCESS_STACK 0xA00
# save memory
define HAL_GCS_ENABLED 0
define HAL_NO_MONITOR_THREAD
define HAL_NO_LOGGING
define HAL_USE_ADC FALSE
# we setup a small defaults.parm
define AP_PARAM_MAX_EMBEDDED_PARAM 256
# debugger support
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# --------------------- SPI1 RM3100+DPS310 -----------------------
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
PA8 BARO_CS CS
# Baro probe
SPIDEV dps310 SPI1 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
BARO DPS310 SPI:dps310
# QMC5883L on I2C2
I2C_ORDER I2C2
PB13 I2C2_SCL I2C2
PB11 I2C2_SDA I2C2
define HAL_I2C_CLEAR_ON_TIMEOUT 0
define HAL_I2C_INTERNAL_MASK 1
2024-01-22 11:18:27 -04:00
COMPASS QMC5883L I2C:0:0xd false ROTATION_YAW_180
2024-01-20 00:15:06 -04:00
# ---------------------- CAN bus -------------------------
PA11 CAN1_RX CAN1
PA12 CAN1_TX CAN1
PB1 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
PB6 GPIO_CAN1_TERM OUTPUT PUSHPULL SPEED_LOW LOW
2024-01-22 11:18:27 -04:00
define HAL_CAN_POOL_SIZE 8000
2024-01-20 00:15:06 -04:00
# ---------------------- UARTs ---------------------------
SERIAL_ORDER EMPTY USART1
# USART1 for GPS
PA9 USART1_TX USART1 SPEED_HIGH
2024-01-22 11:18:27 -04:00
PA10 USART1_RX USART1 SPEED_HIGH
2024-01-20 00:15:06 -04:00
# keep ROMFS uncompressed as we don't have enough RAM
# to uncompress the bootloader at runtime
env ROMFS_UNCOMPRESSED True
# enable GPS and compass
define HAL_PERIPH_ENABLE_GPS
define GPS_MAX_RATE_MS 200
define HAL_PERIPH_ENABLE_MAG
define HAL_PERIPH_ENABLE_BARO
# disable dual GPS and GPS blending to save flash space
define GPS_MAX_RECEIVERS 1
define GPS_MAX_INSTANCES 1
define HAL_COMPASS_MAX_SENSORS 1
define BARO_MAX_INSTANCES 1
define HAL_PERIPH_GPS_PORT_DEFAULT 1
# GPS PPS
2024-01-22 11:18:27 -04:00
PA15 GPS_PPS_IN INPUT
2024-01-20 00:15:06 -04:00
# PWM, WS2812 LED
2024-01-22 11:18:27 -04:00
PB10 TIM2_CH3 TIM2 PWM(1)
2024-01-20 00:15:06 -04:00
define CAN_APP_NODE_NAME "in.sierraaerospace.TrueNavIC"
# Enable GPS LDO
PC13 VDD_3V3_SENSORS_EN OUTPUT HIGH
# do direct neopixel LED output to enable the 'rainbow' effect on startup
define HAL_PERIPH_NEOPIXEL_CHAN_WITHOUT_NOTIFY 0
define HAL_PERIPH_NEOPIXEL_COUNT_WITHOUT_NOTIFY 8
define DEFAULT_NTF_LED_TYPES 455
# PA1 LED OUTPUT LOW GPIO(1)
define HAL_SERIAL_ESC_COMM_ENABLED 1