2019-11-04 02:25:49 -04:00
|
|
|
# hw definition file for processing by chibios_pins.py
|
|
|
|
# for FrSky R9Pilot
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
MCU STM32F7xx STM32F767xx
|
|
|
|
|
|
|
|
# board ID for firmware load
|
2020-03-13 17:05:22 -03:00
|
|
|
APJ_BOARD_ID 1008
|
2019-11-04 02:25:49 -04:00
|
|
|
|
|
|
|
# crystal frequency, setup to use external oscillator
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
|
|
|
|
# leave 2 sectors free
|
|
|
|
FLASH_RESERVE_START_KB 96
|
|
|
|
|
|
|
|
|
|
|
|
# one I2C bus (I2C2 can be used with loss of USART3)
|
|
|
|
I2C_ORDER I2C3
|
|
|
|
|
|
|
|
# order of UARTs (and USB)
|
2020-04-24 08:10:08 -03:00
|
|
|
SERIAL_ORDER OTG1 USART2 USART3 USART1 UART5 USART6 UART7 UART8
|
2019-11-04 02:25:49 -04:00
|
|
|
|
|
|
|
# USB
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PC4 VBUS INPUT OPENDRAIN
|
|
|
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
# SPI1 for baro
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
PA4 BARO_CS CS
|
|
|
|
PA1 BARO_CS2 CS
|
|
|
|
|
|
|
|
# SPI2 external (gyro box, 7 pin ribbon cable)
|
|
|
|
PB13 SPI2_SCK SPI2
|
|
|
|
PB14 SPI2_MISO SPI2
|
|
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
PB12 EXT_CS CS
|
|
|
|
|
|
|
|
# SPI3 for on-board IMU
|
|
|
|
PC10 SPI3_SCK SPI3
|
|
|
|
PC11 SPI3_MISO SPI3
|
|
|
|
PC12 SPI3_MOSI SPI3
|
|
|
|
PA15 IMU_CS CS
|
|
|
|
PE8 MPU3_INT INPUT
|
|
|
|
|
|
|
|
# SPI4 for microSD
|
|
|
|
PE4 SDCARD_CS CS
|
|
|
|
PE2 SPI4_SCK SPI4
|
|
|
|
PE5 SPI4_MISO SPI4
|
|
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
|
|
|
|
# I2C3
|
|
|
|
PA8 I2C3_SCL I2C3
|
|
|
|
PC9 I2C3_SDA I2C3
|
|
|
|
|
|
|
|
# I2C2 (if not USART3)
|
|
|
|
# PB10 I2C2_SCL I2C2
|
|
|
|
# PB11 I2C2_SDA I2C2
|
|
|
|
|
|
|
|
# USART1 for GPS
|
|
|
|
PA10 USART1_RX USART1
|
|
|
|
PA9 USART1_TX USART1
|
|
|
|
|
|
|
|
# USART2 for telem1
|
|
|
|
PD5 USART2_TX USART2
|
|
|
|
PD6 USART2_RX USART2
|
|
|
|
|
|
|
|
# USART3 for telem2
|
|
|
|
PB11 USART3_RX USART3
|
|
|
|
PB10 USART3_TX USART3
|
|
|
|
|
|
|
|
# UART5 spare uart
|
|
|
|
PB5 UART5_RX UART5
|
|
|
|
PB6 UART5_TX UART5
|
|
|
|
|
|
|
|
# USART6, Pixel OSD
|
|
|
|
PC7 USART6_RX USART6
|
|
|
|
PC6 USART6_TX USART6
|
|
|
|
|
|
|
|
# UART7, used for SBUS input
|
|
|
|
PB3 UART7_RX UART7
|
|
|
|
PB4 UART7_TX UART7
|
|
|
|
|
|
|
|
# alternatively use UART7 RX for RCInput using timer
|
|
|
|
PB3 TIM2_CH2 TIM2 RCININT PULLDOWN LOW ALT(1)
|
|
|
|
|
|
|
|
# UART8, marked "RX RFD", connected to RXSR receiver via
|
|
|
|
# 7-pin ribbon cable
|
|
|
|
PE1 UART8_TX UART8 NODMA
|
|
|
|
|
|
|
|
PC3 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
PC2 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
|
|
|
# define default battery setup
|
|
|
|
define HAL_BATT_VOLT_PIN 13
|
|
|
|
define HAL_BATT_CURR_PIN 12
|
|
|
|
define HAL_BATT_VOLT_SCALE 10.1
|
|
|
|
define HAL_BATT_CURR_SCALE 17.0
|
|
|
|
|
|
|
|
# analog RSSI
|
|
|
|
PC5 RSSI_ADC ADC1
|
|
|
|
define BOARD_RSSI_ANA_PIN 15
|
|
|
|
|
|
|
|
# analog pitot option (not on prototype boards)
|
|
|
|
PC0 PRESSURE_SENS ADC1 SCALE(2)
|
|
|
|
define HAL_DEFAULT_AIRSPEED_PIN 10
|
|
|
|
|
|
|
|
PE0 LED0 OUTPUT LOW GPIO(90) # blue
|
|
|
|
PA3 LED1 OUTPUT LOW GPIO(91) # green
|
|
|
|
define HAL_GPIO_A_LED_PIN 91
|
|
|
|
define HAL_GPIO_B_LED_PIN 90
|
|
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
|
|
|
|
# PWM outputs
|
|
|
|
PB0 TIM3_CH3 TIM3 PWM(1) GPIO(50)
|
|
|
|
PB1 TIM3_CH4 TIM3 PWM(2) GPIO(51)
|
|
|
|
PE9 TIM1_CH1 TIM1 PWM(3) GPIO(52)
|
|
|
|
PE11 TIM1_CH2 TIM1 PWM(4) GPIO(53)
|
|
|
|
PE14 TIM1_CH4 TIM1 PWM(5) GPIO(54)
|
|
|
|
PB7 TIM4_CH2 TIM4 PWM(6) GPIO(55)
|
|
|
|
PB8 TIM4_CH3 TIM4 PWM(7) GPIO(56)
|
|
|
|
PB9 TIM4_CH4 TIM4 PWM(8) GPIO(57)
|
|
|
|
|
|
|
|
# tonealarm support
|
|
|
|
PA0 TIM5_CH1 TIM5 GPIO(32) ALARM
|
|
|
|
|
|
|
|
# GPIOs
|
|
|
|
PE3 SD_DETECT INPUT
|
|
|
|
|
|
|
|
# switch1
|
2021-10-03 14:40:45 -03:00
|
|
|
PC8 SW1 INPUT GPIO(70)
|
2019-11-04 02:25:49 -04:00
|
|
|
|
|
|
|
DMA_PRIORITY SPI* ADC*
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
2021-10-27 02:32:43 -03:00
|
|
|
STORAGE_FLASH_PAGE 1
|
2019-11-04 02:25:49 -04:00
|
|
|
|
|
|
|
# spi devices
|
|
|
|
SPIDEV icm20602 SPI3 DEVID1 IMU_CS MODE3 1*MHZ 8*MHZ
|
|
|
|
SPIDEV spl06 SPI1 DEVID1 BARO_CS MODE3 1*MHZ 1*MHZ
|
|
|
|
SPIDEV imu2 SPI2 DEVID1 EXT_CS MODE3 1*MHZ 8*MHZ
|
|
|
|
SPIDEV sdcard SPI4 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
|
|
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
|
|
# external compass types
|
|
|
|
define ALLOW_ARM_NO_COMPASS
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
|
|
|
|
# one main IMU
|
|
|
|
IMU Invensense SPI:icm20602 ROTATION_PITCH_180_YAW_90
|
|
|
|
|
|
|
|
# optional 2nd IMU, support any invensense part, board
|
|
|
|
# may come with a ICM20601 IMU in a plastic case, called
|
|
|
|
# "gyro box"
|
|
|
|
IMU Invensense SPI:imu2 ROTATION_YAW_90
|
|
|
|
|
|
|
|
# also support newer Invensense IMUs
|
|
|
|
IMU Invensensev2 SPI:imu2 ROTATION_YAW_90
|
|
|
|
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 3
|
|
|
|
|
|
|
|
# one BARO, multiple possible choices for different
|
2020-12-23 22:02:11 -04:00
|
|
|
# board variants
|
2019-11-04 02:25:49 -04:00
|
|
|
BARO SPL06 SPI:spl06
|
|
|
|
|
|
|
|
# dummy for testing
|
|
|
|
# BARO Dummy
|
|
|
|
|
|
|
|
# FAT filesystem on microSD
|
|
|
|
define HAL_OS_FATFS_IO 1
|