Jetpack/kernel/nvidia/drivers/net/wireless/bcmdhd/include/sbchipc.h

3647 lines
130 KiB
C
Raw Normal View History

/*
* SiliconBackplane Chipcommon core hardware definitions.
*
* The chipcommon core provides chip identification, SB control,
* JTAG, 0/1/2 UARTs, clock frequency control, a watchdog interrupt timer,
* GPIO interface, extbus, and support for serial and parallel flashes.
*
* $Id: sbchipc.h 474281 2014-04-30 18:24:55Z $
*
* Copyright (C) 1999-2015, Broadcom Corporation
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2 (the "GPL"),
* available at http://www.broadcom.com/licenses/GPLv2.php, with the
* following added to such license:
*
* As a special exception, the copyright holders of this software give you
* permission to link this software with independent modules, and to copy and
* distribute the resulting executable under terms of your choice, provided that
* you also meet, for each linked independent module, the terms and conditions of
* the license of that module. An independent module is a module which is not
* derived from this software. The special exception does not apply to any
* modifications of the software.
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a license
* other than the GPL, without Broadcom's express prior written consent.
*/
#ifndef _SBCHIPC_H
#define _SBCHIPC_H
#if !defined(_LANGUAGE_ASSEMBLY) && !defined(__ASSEMBLY__)
/* cpp contortions to concatenate w/arg prescan */
#ifndef PAD
#define _PADLINE(line) pad ## line
#define _XSTR(line) _PADLINE(line)
#define PAD _XSTR(__LINE__)
#endif /* PAD */
/**
* In chipcommon rev 49 the pmu registers have been moved from chipc to the pmu core if the
* 'AOBPresent' bit of 'CoreCapabilitiesExt' is set. If this field is set, the traditional chipc to
* [pmu|gci|sreng] register interface is deprecated and removed. These register blocks would instead
* be assigned their respective chipc-specific address space and connected to the Always On
* Backplane via the APB interface.
*/
typedef volatile struct {
uint32 PAD[384];
uint32 pmucontrol; /* 0x600 */
uint32 pmucapabilities;
uint32 pmustatus;
uint32 res_state;
uint32 res_pending;
uint32 pmutimer;
uint32 min_res_mask;
uint32 max_res_mask;
uint32 res_table_sel;
uint32 res_dep_mask;
uint32 res_updn_timer;
uint32 res_timer;
uint32 clkstretch;
uint32 pmuwatchdog;
uint32 gpiosel; /* 0x638, rev >= 1 */
uint32 gpioenable; /* 0x63c, rev >= 1 */
uint32 res_req_timer_sel;
uint32 res_req_timer;
uint32 res_req_mask;
uint32 PAD;
uint32 chipcontrol_addr; /* 0x650 */
uint32 chipcontrol_data; /* 0x654 */
uint32 regcontrol_addr;
uint32 regcontrol_data;
uint32 pllcontrol_addr;
uint32 pllcontrol_data;
uint32 pmustrapopt; /* 0x668, corerev >= 28 */
uint32 pmu_xtalfreq; /* 0x66C, pmurev >= 10 */
uint32 retention_ctl; /* 0x670 */
uint32 PAD[3];
uint32 retention_grpidx; /* 0x680 */
uint32 retention_grpctl; /* 0x684 */
uint32 PAD[20];
uint32 pmucontrol_ext; /* 0x6d8 */
uint32 slowclkperiod; /* 0x6dc */
uint32 PAD[8];
uint32 pmuintmask0; /* 0x700 */
uint32 pmuintmask1; /* 0x704 */
uint32 PAD[14];
uint32 pmuintstatus; /* 0x740 */
} pmuregs_t;
typedef struct eci_prerev35 {
uint32 eci_output;
uint32 eci_control;
uint32 eci_inputlo;
uint32 eci_inputmi;
uint32 eci_inputhi;
uint32 eci_inputintpolaritylo;
uint32 eci_inputintpolaritymi;
uint32 eci_inputintpolarityhi;
uint32 eci_intmasklo;
uint32 eci_intmaskmi;
uint32 eci_intmaskhi;
uint32 eci_eventlo;
uint32 eci_eventmi;
uint32 eci_eventhi;
uint32 eci_eventmasklo;
uint32 eci_eventmaskmi;
uint32 eci_eventmaskhi;
uint32 PAD[3];
} eci_prerev35_t;
typedef struct eci_rev35 {
uint32 eci_outputlo;
uint32 eci_outputhi;
uint32 eci_controllo;
uint32 eci_controlhi;
uint32 eci_inputlo;
uint32 eci_inputhi;
uint32 eci_inputintpolaritylo;
uint32 eci_inputintpolarityhi;
uint32 eci_intmasklo;
uint32 eci_intmaskhi;
uint32 eci_eventlo;
uint32 eci_eventhi;
uint32 eci_eventmasklo;
uint32 eci_eventmaskhi;
uint32 eci_auxtx;
uint32 eci_auxrx;
uint32 eci_datatag;
uint32 eci_uartescvalue;
uint32 eci_autobaudctr;
uint32 eci_uartfifolevel;
} eci_rev35_t;
typedef struct flash_config {
uint32 PAD[19];
/* Flash struct configuration registers (0x18c) for BCM4706 (corerev = 31) */
uint32 flashstrconfig;
} flash_config_t;
typedef volatile struct {
uint32 chipid; /* 0x0 */
uint32 capabilities;
uint32 corecontrol; /* corerev >= 1 */
uint32 bist;
/* OTP */
uint32 otpstatus; /* 0x10, corerev >= 10 */
uint32 otpcontrol;
uint32 otpprog;
uint32 otplayout; /* corerev >= 23 */
/* Interrupt control */
uint32 intstatus; /* 0x20 */
uint32 intmask;
/* Chip specific regs */
uint32 chipcontrol; /* 0x28, rev >= 11 */
uint32 chipstatus; /* 0x2c, rev >= 11 */
/* Jtag Master */
uint32 jtagcmd; /* 0x30, rev >= 10 */
uint32 jtagir;
uint32 jtagdr;
uint32 jtagctrl;
/* serial flash interface registers */
uint32 flashcontrol; /* 0x40 */
uint32 flashaddress;
uint32 flashdata;
uint32 otplayoutextension; /* rev >= 35 */
/* Silicon backplane configuration broadcast control */
uint32 broadcastaddress; /* 0x50 */
uint32 broadcastdata;
/* gpio - cleared only by power-on-reset */
uint32 gpiopullup; /* 0x58, corerev >= 20 */
uint32 gpiopulldown; /* 0x5c, corerev >= 20 */
uint32 gpioin; /* 0x60 */
uint32 gpioout; /* 0x64 */
uint32 gpioouten; /* 0x68 */
uint32 gpiocontrol; /* 0x6C */
uint32 gpiointpolarity; /* 0x70 */
uint32 gpiointmask; /* 0x74 */
/* GPIO events corerev >= 11 */
uint32 gpioevent;
uint32 gpioeventintmask;
/* Watchdog timer */
uint32 watchdog; /* 0x80 */
/* GPIO events corerev >= 11 */
uint32 gpioeventintpolarity;
/* GPIO based LED powersave registers corerev >= 16 */
uint32 gpiotimerval; /* 0x88 */
uint32 gpiotimeroutmask;
/* clock control */
uint32 clockcontrol_n; /* 0x90 */
uint32 clockcontrol_sb; /* aka m0 */
uint32 clockcontrol_pci; /* aka m1 */
uint32 clockcontrol_m2; /* mii/uart/mipsref */
uint32 clockcontrol_m3; /* cpu */
uint32 clkdiv; /* corerev >= 3 */
uint32 gpiodebugsel; /* corerev >= 28 */
uint32 capabilities_ext; /* 0xac */
/* pll delay registers (corerev >= 4) */
uint32 pll_on_delay; /* 0xb0 */
uint32 fref_sel_delay;
uint32 slow_clk_ctl; /* 5 < corerev < 10 */
uint32 PAD;
/* Instaclock registers (corerev >= 10) */
uint32 system_clk_ctl; /* 0xc0 */
uint32 clkstatestretch;
uint32 PAD[2];
/* Indirect backplane access (corerev >= 22) */
uint32 bp_addrlow; /* 0xd0 */
uint32 bp_addrhigh;
uint32 bp_data;
uint32 PAD;
uint32 bp_indaccess;
/* SPI registers, corerev >= 37 */
uint32 gsioctrl;
uint32 gsioaddress;
uint32 gsiodata;
/* More clock dividers (corerev >= 32) */
uint32 clkdiv2;
/* FAB ID (corerev >= 40) */
uint32 otpcontrol1;
uint32 fabid; /* 0xf8 */
/* In AI chips, pointer to erom */
uint32 eromptr; /* 0xfc */
/* ExtBus control registers (corerev >= 3) */
uint32 pcmcia_config; /* 0x100 */
uint32 pcmcia_memwait;
uint32 pcmcia_attrwait;
uint32 pcmcia_iowait;
uint32 ide_config;
uint32 ide_memwait;
uint32 ide_attrwait;
uint32 ide_iowait;
uint32 prog_config;
uint32 prog_waitcount;
uint32 flash_config;
uint32 flash_waitcount;
uint32 SECI_config; /* 0x130 SECI configuration */
uint32 SECI_status;
uint32 SECI_statusmask;
uint32 SECI_rxnibchanged;
uint32 PAD[20];
/* SROM interface (corerev >= 32) */
uint32 sromcontrol; /* 0x190 */
uint32 sromaddress;
uint32 sromdata;
uint32 PAD[1]; /* 0x19C */
/* NAND flash registers for BCM4706 (corerev = 31) */
uint32 nflashctrl; /* 0x1a0 */
uint32 nflashconf;
uint32 nflashcoladdr;
uint32 nflashrowaddr;
uint32 nflashdata;
uint32 nflashwaitcnt0; /* 0x1b4 */
uint32 PAD[2];
uint32 seci_uart_data; /* 0x1C0 */
uint32 seci_uart_bauddiv;
uint32 seci_uart_fcr;
uint32 seci_uart_lcr;
uint32 seci_uart_mcr;
uint32 seci_uart_lsr;
uint32 seci_uart_msr;
uint32 seci_uart_baudadj;
/* Clock control and hardware workarounds (corerev >= 20) */
uint32 clk_ctl_st; /* 0x1e0 */
uint32 hw_war;
uint32 PAD[70];
/* UARTs */
uint8 uart0data; /* 0x300 */
uint8 uart0imr;
uint8 uart0fcr;
uint8 uart0lcr;
uint8 uart0mcr;
uint8 uart0lsr;
uint8 uart0msr;
uint8 uart0scratch;
uint8 PAD[248]; /* corerev >= 1 */
uint8 uart1data; /* 0x400 */
uint8 uart1imr;
uint8 uart1fcr;
uint8 uart1lcr;
uint8 uart1mcr;
uint8 uart1lsr;
uint8 uart1msr;
uint8 uart1scratch; /* 0x407 */
uint32 PAD[62];
/* save/restore, corerev >= 48 */
uint32 sr_capability; /* 0x500 */
uint32 sr_control0; /* 0x504 */
uint32 sr_control1; /* 0x508 */
uint32 gpio_control; /* 0x50C */
uint32 PAD[60];
/* PMU registers (corerev >= 20) */
/* Note: all timers driven by ILP clock are updated asynchronously to HT/ALP.
* The CPU must read them twice, compare, and retry if different.
*/
uint32 pmucontrol; /* 0x600 */
uint32 pmucapabilities;
uint32 pmustatus;
uint32 res_state;
uint32 res_pending;
uint32 pmutimer;
uint32 min_res_mask;
uint32 max_res_mask;
uint32 res_table_sel;
uint32 res_dep_mask;
uint32 res_updn_timer;
uint32 res_timer;
uint32 clkstretch;
uint32 pmuwatchdog;
uint32 gpiosel; /* 0x638, rev >= 1 */
uint32 gpioenable; /* 0x63c, rev >= 1 */
uint32 res_req_timer_sel;
uint32 res_req_timer;
uint32 res_req_mask;
uint32 PAD;
uint32 chipcontrol_addr; /* 0x650 */
uint32 chipcontrol_data; /* 0x654 */
uint32 regcontrol_addr;
uint32 regcontrol_data;
uint32 pllcontrol_addr;
uint32 pllcontrol_data;
uint32 pmustrapopt; /* 0x668, corerev >= 28 */
uint32 pmu_xtalfreq; /* 0x66C, pmurev >= 10 */
uint32 retention_ctl; /* 0x670 */
uint32 PAD[3];
uint32 retention_grpidx; /* 0x680 */
uint32 retention_grpctl; /* 0x684 */
uint32 PAD[20];
uint32 pmucontrol_ext; /* 0x6d8 */
uint32 slowclkperiod; /* 0x6dc */
uint32 PAD[8];
uint32 pmuintmask0; /* 0x700 */
uint32 pmuintmask1; /* 0x704 */
uint32 PAD[14];
uint32 pmuintstatus; /* 0x740 */
uint32 PAD[47];
uint16 sromotp[512]; /* 0x800 */
#ifdef NFLASH_SUPPORT
/* Nand flash MLC controller registers (corerev >= 38) */
uint32 nand_revision; /* 0xC00 */
uint32 nand_cmd_start;
uint32 nand_cmd_addr_x;
uint32 nand_cmd_addr;
uint32 nand_cmd_end_addr;
uint32 nand_cs_nand_select;
uint32 nand_cs_nand_xor;
uint32 PAD;
uint32 nand_spare_rd0;
uint32 nand_spare_rd4;
uint32 nand_spare_rd8;
uint32 nand_spare_rd12;
uint32 nand_spare_wr0;
uint32 nand_spare_wr4;
uint32 nand_spare_wr8;
uint32 nand_spare_wr12;
uint32 nand_acc_control;
uint32 PAD;
uint32 nand_config;
uint32 PAD;
uint32 nand_timing_1;
uint32 nand_timing_2;
uint32 nand_semaphore;
uint32 PAD;
uint32 nand_devid;
uint32 nand_devid_x;
uint32 nand_block_lock_status;
uint32 nand_intfc_status;
uint32 nand_ecc_corr_addr_x;
uint32 nand_ecc_corr_addr;
uint32 nand_ecc_unc_addr_x;
uint32 nand_ecc_unc_addr;
uint32 nand_read_error_count;
uint32 nand_corr_stat_threshold;
uint32 PAD[2];
uint32 nand_read_addr_x;
uint32 nand_read_addr;
uint32 nand_page_program_addr_x;
uint32 nand_page_program_addr;
uint32 nand_copy_back_addr_x;
uint32 nand_copy_back_addr;
uint32 nand_block_erase_addr_x;
uint32 nand_block_erase_addr;
uint32 nand_inv_read_addr_x;
uint32 nand_inv_read_addr;
uint32 PAD[2];
uint32 nand_blk_wr_protect;
uint32 PAD[3];
uint32 nand_acc_control_cs1;
uint32 nand_config_cs1;
uint32 nand_timing_1_cs1;
uint32 nand_timing_2_cs1;
uint32 PAD[20];
uint32 nand_spare_rd16;
uint32 nand_spare_rd20;
uint32 nand_spare_rd24;
uint32 nand_spare_rd28;
uint32 nand_cache_addr;
uint32 nand_cache_data;
uint32 nand_ctrl_config;
uint32 nand_ctrl_status;
#endif /* NFLASH_SUPPORT */
uint32 gci_corecaps0; /* GCI starting at 0xC00 */
uint32 gci_corecaps1;
uint32 gci_corecaps2;
uint32 gci_corectrl;
uint32 gci_corestat; /* 0xC10 */
uint32 gci_intstat; /* 0xC14 */
uint32 gci_intmask; /* 0xC18 */
uint32 gci_wakemask; /* 0xC1C */
uint32 gci_levelintstat; /* 0xC20 */
uint32 gci_eventintstat; /* 0xC24 */
uint32 PAD[6];
uint32 gci_indirect_addr; /* 0xC40 */
uint32 gci_gpioctl; /* 0xC44 */
uint32 gci_gpiostatus;
uint32 gci_gpiomask; /* 0xC4C */
uint32 PAD;
uint32 gci_miscctl; /* 0xC54 */
uint32 gci_gpiointmask;
uint32 gci_gpiowakemask;
uint32 gci_input[32]; /* C60 */
uint32 gci_event[32]; /* CE0 */
uint32 gci_output[4]; /* D60 */
uint32 gci_control_0; /* 0xD70 */
uint32 gci_control_1; /* 0xD74 */
uint32 gci_intpolreg; /* 0xD78 */
uint32 gci_levelintmask; /* 0xD7C */
uint32 gci_eventintmask; /* 0xD80 */
uint32 PAD[3];
uint32 gci_inbandlevelintmask; /* 0xD90 */
uint32 gci_inbandeventintmask; /* 0xD94 */
uint32 PAD[2];
uint32 gci_seciauxtx; /* 0xDA0 */
uint32 gci_seciauxrx; /* 0xDA4 */
uint32 gci_secitx_datatag; /* 0xDA8 */
uint32 gci_secirx_datatag; /* 0xDAC */
uint32 gci_secitx_datamask; /* 0xDB0 */
uint32 gci_seciusef0tx_reg; /* 0xDB4 */
uint32 gci_secif0tx_offset; /* 0xDB8 */
uint32 gci_secif0rx_offset; /* 0xDBC */
uint32 gci_secif1tx_offset; /* 0xDC0 */
uint32 gci_rxfifo_common_ctrl; /* 0xDC4 */
uint32 gci_rxfifoctrl; /* 0xDC8 */
uint32 gci_uartreadid; /* DCC */
uint32 gci_uartescval; /* DD0 */
uint32 PAD;
uint32 gci_secififolevel; /* DD8 */
uint32 gci_seciuartdata; /* DDC */
uint32 gci_secibauddiv; /* DE0 */
uint32 gci_secifcr; /* DE4 */
uint32 gci_secilcr; /* DE8 */
uint32 gci_secimcr; /* DEC */
uint32 gci_secilsr; /* DF0 */
uint32 gci_secimsr; /* DF4 */
uint32 gci_baudadj; /* DF8 */
uint32 PAD;
uint32 gci_chipctrl; /* 0xE00 */
uint32 gci_chipsts; /* 0xE04 */
uint32 gci_gpioout; /* 0xE08 */
uint32 gci_gpioout_read; /* 0xE0C */
uint32 gci_mpwaketx; /* 0xE10 */
uint32 gci_mpwakedetect; /* 0xE14 */
uint32 gci_seciin_ctrl; /* 0xE18 */
uint32 gci_seciout_ctrl; /* 0xE1C */
uint32 gci_seciin_auxfifo_en; /* 0xE20 */
uint32 gci_seciout_txen_txbr; /* 0xE24 */
uint32 gci_seciin_rxbrstatus; /* 0xE28 */
uint32 gci_seciin_rxerrstatus; /* 0xE2C */
uint32 gci_seciin_fcstatus; /* 0xE30 */
uint32 gci_seciout_txstatus; /* 0xE34 */
uint32 gci_seciout_txbrstatus; /* 0xE38 */
} chipcregs_t;
#endif /* !_LANGUAGE_ASSEMBLY && !__ASSEMBLY__ */
#define CC_CHIPID 0
#define CC_CAPABILITIES 4
#define CC_CHIPST 0x2c
#define CC_EROMPTR 0xfc
#define CC_OTPST 0x10
#define CC_INTSTATUS 0x20
#define CC_INTMASK 0x24
#define CC_JTAGCMD 0x30
#define CC_JTAGIR 0x34
#define CC_JTAGDR 0x38
#define CC_JTAGCTRL 0x3c
#define CC_GPIOPU 0x58
#define CC_GPIOPD 0x5c
#define CC_GPIOIN 0x60
#define CC_GPIOOUT 0x64
#define CC_GPIOOUTEN 0x68
#define CC_GPIOCTRL 0x6c
#define CC_GPIOPOL 0x70
#define CC_GPIOINTM 0x74
#define CC_GPIOEVENT 0x78
#define CC_GPIOEVENTMASK 0x7c
#define CC_WATCHDOG 0x80
#define CC_GPIOEVENTPOL 0x84
#define CC_CLKC_N 0x90
#define CC_CLKC_M0 0x94
#define CC_CLKC_M1 0x98
#define CC_CLKC_M2 0x9c
#define CC_CLKC_M3 0xa0
#define CC_CLKDIV 0xa4
#define CC_SYS_CLK_CTL 0xc0
#define CC_CLK_CTL_ST SI_CLK_CTL_ST
#define PMU_CTL 0x600
#define PMU_CAP 0x604
#define PMU_ST 0x608
#define PMU_RES_STATE 0x60c
#define PMU_RES_PENDING 0x610
#define PMU_TIMER 0x614
#define PMU_MIN_RES_MASK 0x618
#define PMU_MAX_RES_MASK 0x61c
#define CC_CHIPCTL_ADDR 0x650
#define CC_CHIPCTL_DATA 0x654
#define PMU_REG_CONTROL_ADDR 0x658
#define PMU_REG_CONTROL_DATA 0x65C
#define PMU_PLL_CONTROL_ADDR 0x660
#define PMU_PLL_CONTROL_DATA 0x664
#define CC_SROM_CTRL 0x190
#define CC_SROM_OTP 0x800 /* SROM/OTP address space */
#define CC_GCI_INDIRECT_ADDR_REG 0xC40
#define CC_GCI_CHIP_CTRL_REG 0xE00
#define CC_GCI_CC_OFFSET_2 2
#define CC_GCI_CC_OFFSET_5 5
#define CC_SWD_CTRL 0x380
#define CC_SWD_REQACK 0x384
#define CC_SWD_DATA 0x388
#define CHIPCTRLREG0 0x0
#define CHIPCTRLREG1 0x1
#define CHIPCTRLREG2 0x2
#define CHIPCTRLREG3 0x3
#define CHIPCTRLREG4 0x4
#define CHIPCTRLREG5 0x5
#define CHIPCTRLREG6 0x6
#define REGCTRLREG4 0x4
#define REGCTRLREG5 0x5
#define REGCTRLREG6 0x6
#define MINRESMASKREG 0x618
#define MAXRESMASKREG 0x61c
#define CHIPCTRLADDR 0x650
#define CHIPCTRLDATA 0x654
#define RSRCTABLEADDR 0x620
#define PMU_RES_DEP_MASK 0x624
#define RSRCUPDWNTIME 0x628
#define PMUREG_RESREQ_MASK 0x68c
#define EXT_LPO_AVAIL 0x100
#define LPO_SEL (1 << 0)
#define CC_EXT_LPO_PU 0x200000
#define GC_EXT_LPO_PU 0x2
#define CC_INT_LPO_PU 0x100000
#define GC_INT_LPO_PU 0x1
#define EXT_LPO_SEL 0x8
#define INT_LPO_SEL 0x4
#define ENABLE_FINE_CBUCK_CTRL (1 << 30)
#define REGCTRL5_PWM_AUTO_CTRL_MASK 0x007e0000
#define REGCTRL5_PWM_AUTO_CTRL_SHIFT 17
#define REGCTRL6_PWM_AUTO_CTRL_MASK 0x3fff0000
#define REGCTRL6_PWM_AUTO_CTRL_SHIFT 16
#ifdef SR_DEBUG
#define SUBCORE_POWER_ON 0x0001
#define PHY_POWER_ON 0x0010
#define VDDM_POWER_ON 0x0100
#define MEMLPLDO_POWER_ON 0x1000
#define SUBCORE_POWER_ON_CHK 0x00040000
#define PHY_POWER_ON_CHK 0x00080000
#define VDDM_POWER_ON_CHK 0x00100000
#define MEMLPLDO_POWER_ON_CHK 0x00200000
#endif /* SR_DEBUG */
#ifdef NFLASH_SUPPORT
/* NAND flash support */
#define CC_NAND_REVISION 0xC00
#define CC_NAND_CMD_START 0xC04
#define CC_NAND_CMD_ADDR 0xC0C
#define CC_NAND_SPARE_RD_0 0xC20
#define CC_NAND_SPARE_RD_4 0xC24
#define CC_NAND_SPARE_RD_8 0xC28
#define CC_NAND_SPARE_RD_C 0xC2C
#define CC_NAND_CONFIG 0xC48
#define CC_NAND_DEVID 0xC60
#define CC_NAND_DEVID_EXT 0xC64
#define CC_NAND_INTFC_STATUS 0xC6C
#endif /* NFLASH_SUPPORT */
/* chipid */
#define CID_ID_MASK 0x0000ffff /* Chip Id mask */
#define CID_REV_MASK 0x000f0000 /* Chip Revision mask */
#define CID_REV_SHIFT 16 /* Chip Revision shift */
#define CID_PKG_MASK 0x00f00000 /* Package Option mask */
#define CID_PKG_SHIFT 20 /* Package Option shift */
#define CID_CC_MASK 0x0f000000 /* CoreCount (corerev >= 4) */
#define CID_CC_SHIFT 24
#define CID_TYPE_MASK 0xf0000000 /* Chip Type */
#define CID_TYPE_SHIFT 28
/* capabilities */
#define CC_CAP_UARTS_MASK 0x00000003 /* Number of UARTs */
#define CC_CAP_MIPSEB 0x00000004 /* MIPS is in big-endian mode */
#define CC_CAP_UCLKSEL 0x00000018 /* UARTs clock select */
#define CC_CAP_UINTCLK 0x00000008 /* UARTs are driven by internal divided clock */
#define CC_CAP_UARTGPIO 0x00000020 /* UARTs own GPIOs 15:12 */
#define CC_CAP_EXTBUS_MASK 0x000000c0 /* External bus mask */
#define CC_CAP_EXTBUS_NONE 0x00000000 /* No ExtBus present */
#define CC_CAP_EXTBUS_FULL 0x00000040 /* ExtBus: PCMCIA, IDE & Prog */
#define CC_CAP_EXTBUS_PROG 0x00000080 /* ExtBus: ProgIf only */
#define CC_CAP_FLASH_MASK 0x00000700 /* Type of flash */
#define CC_CAP_PLL_MASK 0x00038000 /* Type of PLL */
#define CC_CAP_PWR_CTL 0x00040000 /* Power control */
#define CC_CAP_OTPSIZE 0x00380000 /* OTP Size (0 = none) */
#define CC_CAP_OTPSIZE_SHIFT 19 /* OTP Size shift */
#define CC_CAP_OTPSIZE_BASE 5 /* OTP Size base */
#define CC_CAP_JTAGP 0x00400000 /* JTAG Master Present */
#define CC_CAP_ROM 0x00800000 /* Internal boot rom active */
#define CC_CAP_BKPLN64 0x08000000 /* 64-bit backplane */
#define CC_CAP_PMU 0x10000000 /* PMU Present, rev >= 20 */
#define CC_CAP_ECI 0x20000000 /* ECI Present, rev >= 21 */
#define CC_CAP_SROM 0x40000000 /* Srom Present, rev >= 32 */
#define CC_CAP_NFLASH 0x80000000 /* Nand flash present, rev >= 35 */
#define CC_CAP2_SECI 0x00000001 /* SECI Present, rev >= 36 */
#define CC_CAP2_GSIO 0x00000002 /* GSIO (spi/i2c) present, rev >= 37 */
/* capabilities extension */
#define CC_CAP_EXT_SECI_PRESENT 0x00000001 /* SECI present */
#define CC_CAP_EXT_GSIO_PRESENT 0x00000002 /* GSIO present */
#define CC_CAP_EXT_GCI_PRESENT 0x00000004 /* GCI present */
#define CC_CAP_EXT_AOB_PRESENT 0x00000040 /* AOB present */
/* WL Channel Info to BT via GCI - bits 40 - 47 */
#define GCI_WL_CHN_INFO_MASK (0xFF00)
/* PLL type */
#define PLL_NONE 0x00000000
#define PLL_TYPE1 0x00010000 /* 48MHz base, 3 dividers */
#define PLL_TYPE2 0x00020000 /* 48MHz, 4 dividers */
#define PLL_TYPE3 0x00030000 /* 25MHz, 2 dividers */
#define PLL_TYPE4 0x00008000 /* 48MHz, 4 dividers */
#define PLL_TYPE5 0x00018000 /* 25MHz, 4 dividers */
#define PLL_TYPE6 0x00028000 /* 100/200 or 120/240 only */
#define PLL_TYPE7 0x00038000 /* 25MHz, 4 dividers */
/* ILP clock */
#define ILP_CLOCK 32000
/* ALP clock on pre-PMU chips */
#define ALP_CLOCK 20000000
#ifdef CFG_SIM
#define NS_ALP_CLOCK 84922
#define NS_SLOW_ALP_CLOCK 84922
#define NS_CPU_CLOCK 534500
#define NS_SLOW_CPU_CLOCK 534500
#define NS_SI_CLOCK 271750
#define NS_SLOW_SI_CLOCK 271750
#define NS_FAST_MEM_CLOCK 271750
#define NS_MEM_CLOCK 271750
#define NS_SLOW_MEM_CLOCK 271750
#else
#define NS_ALP_CLOCK 125000000
#define NS_SLOW_ALP_CLOCK 100000000
#define NS_CPU_CLOCK 1000000000
#define NS_SLOW_CPU_CLOCK 800000000
#define NS_SI_CLOCK 250000000
#define NS_SLOW_SI_CLOCK 200000000
#define NS_FAST_MEM_CLOCK 800000000
#define NS_MEM_CLOCK 533000000
#define NS_SLOW_MEM_CLOCK 400000000
#endif /* CFG_SIM */
/* HT clock */
#define HT_CLOCK 80000000
/* corecontrol */
#define CC_UARTCLKO 0x00000001 /* Drive UART with internal clock */
#define CC_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
#define CC_ASYNCGPIO 0x00000004 /* 1=generate GPIO interrupt without backplane clock */
#define CC_UARTCLKEN 0x00000008 /* enable UART Clock (corerev > = 21 */
/* 4321 chipcontrol */
#define CHIPCTRL_4321A0_DEFAULT 0x3a4
#define CHIPCTRL_4321A1_DEFAULT 0x0a4
#define CHIPCTRL_4321_PLL_DOWN 0x800000 /* serdes PLL down override */
/* Fields in the otpstatus register in rev >= 21 */
#define OTPS_OL_MASK 0x000000ff
#define OTPS_OL_MFG 0x00000001 /* manuf row is locked */
#define OTPS_OL_OR1 0x00000002 /* otp redundancy row 1 is locked */
#define OTPS_OL_OR2 0x00000004 /* otp redundancy row 2 is locked */
#define OTPS_OL_GU 0x00000008 /* general use region is locked */
#define OTPS_GUP_MASK 0x00000f00
#define OTPS_GUP_SHIFT 8
#define OTPS_GUP_HW 0x00000100 /* h/w subregion is programmed */
#define OTPS_GUP_SW 0x00000200 /* s/w subregion is programmed */
#define OTPS_GUP_CI 0x00000400 /* chipid/pkgopt subregion is programmed */
#define OTPS_GUP_FUSE 0x00000800 /* fuse subregion is programmed */
#define OTPS_READY 0x00001000
#define OTPS_RV(x) (1 << (16 + (x))) /* redundancy entry valid */
#define OTPS_RV_MASK 0x0fff0000
#define OTPS_PROGOK 0x40000000
/* Fields in the otpcontrol register in rev >= 21 */
#define OTPC_PROGSEL 0x00000001
#define OTPC_PCOUNT_MASK 0x0000000e
#define OTPC_PCOUNT_SHIFT 1
#define OTPC_VSEL_MASK 0x000000f0
#define OTPC_VSEL_SHIFT 4
#define OTPC_TMM_MASK 0x00000700
#define OTPC_TMM_SHIFT 8
#define OTPC_ODM 0x00000800
#define OTPC_PROGEN 0x80000000
/* Fields in the 40nm otpcontrol register in rev >= 40 */
#define OTPC_40NM_PROGSEL_SHIFT 0
#define OTPC_40NM_PCOUNT_SHIFT 1
#define OTPC_40NM_PCOUNT_WR 0xA
#define OTPC_40NM_PCOUNT_V1X 0xB
#define OTPC_40NM_REGCSEL_SHIFT 5
#define OTPC_40NM_REGCSEL_DEF 0x4
#define OTPC_40NM_PROGIN_SHIFT 8
#define OTPC_40NM_R2X_SHIFT 10
#define OTPC_40NM_ODM_SHIFT 11
#define OTPC_40NM_DF_SHIFT 15
#define OTPC_40NM_VSEL_SHIFT 16
#define OTPC_40NM_VSEL_WR 0xA
#define OTPC_40NM_VSEL_V1X 0xA
#define OTPC_40NM_VSEL_R1X 0x5
#define OTPC_40NM_COFAIL_SHIFT 30
#define OTPC1_CPCSEL_SHIFT 0
#define OTPC1_CPCSEL_DEF 6
#define OTPC1_TM_SHIFT 8
#define OTPC1_TM_WR 0x84
#define OTPC1_TM_V1X 0x84
#define OTPC1_TM_R1X 0x4
#define OTPC1_CLK_EN_MASK 0x00020000
#define OTPC1_CLK_DIV_MASK 0x00FC0000
/* Fields in otpprog in rev >= 21 and HND OTP */
#define OTPP_COL_MASK 0x000000ff
#define OTPP_COL_SHIFT 0
#define OTPP_ROW_MASK 0x0000ff00
#define OTPP_ROW_MASK9 0x0001ff00 /* for ccrev >= 49 */
#define OTPP_ROW_SHIFT 8
#define OTPP_OC_MASK 0x0f000000
#define OTPP_OC_SHIFT 24
#define OTPP_READERR 0x10000000
#define OTPP_VALUE_MASK 0x20000000
#define OTPP_VALUE_SHIFT 29
#define OTPP_START_BUSY 0x80000000
#define OTPP_READ 0x40000000 /* HND OTP */
/* Fields in otplayout register */
#define OTPL_HWRGN_OFF_MASK 0x00000FFF
#define OTPL_HWRGN_OFF_SHIFT 0
#define OTPL_WRAP_REVID_MASK 0x00F80000
#define OTPL_WRAP_REVID_SHIFT 19
#define OTPL_WRAP_TYPE_MASK 0x00070000
#define OTPL_WRAP_TYPE_SHIFT 16
#define OTPL_WRAP_TYPE_65NM 0
#define OTPL_WRAP_TYPE_40NM 1
#define OTPL_ROW_SIZE_MASK 0x0000F000
#define OTPL_ROW_SIZE_SHIFT 12
/* otplayout reg corerev >= 36 */
#define OTP_CISFORMAT_NEW 0x80000000
/* Opcodes for OTPP_OC field */
#define OTPPOC_READ 0
#define OTPPOC_BIT_PROG 1
#define OTPPOC_VERIFY 3
#define OTPPOC_INIT 4
#define OTPPOC_SET 5
#define OTPPOC_RESET 6
#define OTPPOC_OCST 7
#define OTPPOC_ROW_LOCK 8
#define OTPPOC_PRESCN_TEST 9
/* Opcodes for OTPP_OC field (40NM) */
#define OTPPOC_READ_40NM 0
#define OTPPOC_PROG_ENABLE_40NM 1
#define OTPPOC_PROG_DISABLE_40NM 2
#define OTPPOC_VERIFY_40NM 3
#define OTPPOC_WORD_VERIFY_1_40NM 4
#define OTPPOC_ROW_LOCK_40NM 5
#define OTPPOC_STBY_40NM 6
#define OTPPOC_WAKEUP_40NM 7
#define OTPPOC_WORD_VERIFY_0_40NM 8
#define OTPPOC_PRESCN_TEST_40NM 9
#define OTPPOC_BIT_PROG_40NM 10
#define OTPPOC_WORDPROG_40NM 11
#define OTPPOC_BURNIN_40NM 12
#define OTPPOC_AUTORELOAD_40NM 13
#define OTPPOC_OVST_READ_40NM 14
#define OTPPOC_OVST_PROG_40NM 15
/* Fields in otplayoutextension */
#define OTPLAYOUTEXT_FUSE_MASK 0x3FF
/* Jtagm characteristics that appeared at a given corerev */
#define JTAGM_CREV_OLD 10 /* Old command set, 16bit max IR */
#define JTAGM_CREV_IRP 22 /* Able to do pause-ir */
#define JTAGM_CREV_RTI 28 /* Able to do return-to-idle */
/* jtagcmd */
#define JCMD_START 0x80000000
#define JCMD_BUSY 0x80000000
#define JCMD_STATE_MASK 0x60000000
#define JCMD_STATE_TLR 0x00000000 /* Test-logic-reset */
#define JCMD_STATE_PIR 0x20000000 /* Pause IR */
#define JCMD_STATE_PDR 0x40000000 /* Pause DR */
#define JCMD_STATE_RTI 0x60000000 /* Run-test-idle */
#define JCMD0_ACC_MASK 0x0000f000
#define JCMD0_ACC_IRDR 0x00000000
#define JCMD0_ACC_DR 0x00001000
#define JCMD0_ACC_IR 0x00002000
#define JCMD0_ACC_RESET 0x00003000
#define JCMD0_ACC_IRPDR 0x00004000
#define JCMD0_ACC_PDR 0x00005000
#define JCMD0_IRW_MASK 0x00000f00
#define JCMD_ACC_MASK 0x000f0000 /* Changes for corerev 11 */
#define JCMD_ACC_IRDR 0x00000000
#define JCMD_ACC_DR 0x00010000
#define JCMD_ACC_IR 0x00020000
#define JCMD_ACC_RESET 0x00030000
#define JCMD_ACC_IRPDR 0x00040000
#define JCMD_ACC_PDR 0x00050000
#define JCMD_ACC_PIR 0x00060000
#define JCMD_ACC_IRDR_I 0x00070000 /* rev 28: return to run-test-idle */
#define JCMD_ACC_DR_I 0x00080000 /* rev 28: return to run-test-idle */
#define JCMD_IRW_MASK 0x00001f00
#define JCMD_IRW_SHIFT 8
#define JCMD_DRW_MASK 0x0000003f
/* jtagctrl */
#define JCTRL_FORCE_CLK 4 /* Force clock */
#define JCTRL_EXT_EN 2 /* Enable external targets */
#define JCTRL_EN 1 /* Enable Jtag master */
#define JCTRL_TAPSEL_BIT 0x00000008 /* JtagMasterCtrl tap_sel bit */
/* Fields in clkdiv */
#define CLKD_SFLASH 0x0f000000
#define CLKD_SFLASH_SHIFT 24
#define CLKD_OTP 0x000f0000
#define CLKD_OTP_SHIFT 16
#define CLKD_JTAG 0x00000f00
#define CLKD_JTAG_SHIFT 8
#define CLKD_UART 0x000000ff
#define CLKD2_SROM 0x00000003
/* intstatus/intmask */
#define CI_GPIO 0x00000001 /* gpio intr */
#define CI_EI 0x00000002 /* extif intr (corerev >= 3) */
#define CI_TEMP 0x00000004 /* temp. ctrl intr (corerev >= 15) */
#define CI_SIRQ 0x00000008 /* serial IRQ intr (corerev >= 15) */
#define CI_ECI 0x00000010 /* eci intr (corerev >= 21) */
#define CI_PMU 0x00000020 /* pmu intr (corerev >= 21) */
#define CI_UART 0x00000040 /* uart intr (corerev >= 21) */
#define CI_WDRESET 0x80000000 /* watchdog reset occurred */
/* slow_clk_ctl */
#define SCC_SS_MASK 0x00000007 /* slow clock source mask */
#define SCC_SS_LPO 0x00000000 /* source of slow clock is LPO */
#define SCC_SS_XTAL 0x00000001 /* source of slow clock is crystal */
#define SCC_SS_PCI 0x00000002 /* source of slow clock is PCI */
#define SCC_LF 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */
#define SCC_LP 0x00000400 /* LPOPowerDown, 1: LPO is disabled,
* 0: LPO is enabled
*/
#define SCC_FS 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock,
* 0: power logic control
*/
#define SCC_IP 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors
* PLL clock disable requests from core
*/
#define SCC_XC 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't
* disable crystal when appropriate
*/
#define SCC_XP 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */
#define SCC_CD_MASK 0xffff0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */
#define SCC_CD_SHIFT 16
/* system_clk_ctl */
#define SYCC_IE 0x00000001 /* ILPen: Enable Idle Low Power */
#define SYCC_AE 0x00000002 /* ALPen: Enable Active Low Power */
#define SYCC_FP 0x00000004 /* ForcePLLOn */
#define SYCC_AR 0x00000008 /* Force ALP (or HT if ALPen is not set */
#define SYCC_HR 0x00000010 /* Force HT */
#define SYCC_CD_MASK 0xffff0000 /* ClkDiv (ILP = 1/(4 * (divisor + 1)) */
#define SYCC_CD_SHIFT 16
/* Indirect backplane access */
#define BPIA_BYTEEN 0x0000000f
#define BPIA_SZ1 0x00000001
#define BPIA_SZ2 0x00000003
#define BPIA_SZ4 0x00000007
#define BPIA_SZ8 0x0000000f
#define BPIA_WRITE 0x00000100
#define BPIA_START 0x00000200
#define BPIA_BUSY 0x00000200
#define BPIA_ERROR 0x00000400
/* pcmcia/prog/flash_config */
#define CF_EN 0x00000001 /* enable */
#define CF_EM_MASK 0x0000000e /* mode */
#define CF_EM_SHIFT 1
#define CF_EM_FLASH 0 /* flash/asynchronous mode */
#define CF_EM_SYNC 2 /* synchronous mode */
#define CF_EM_PCMCIA 4 /* pcmcia mode */
#define CF_DS 0x00000010 /* destsize: 0=8bit, 1=16bit */
#define CF_BS 0x00000020 /* byteswap */
#define CF_CD_MASK 0x000000c0 /* clock divider */
#define CF_CD_SHIFT 6
#define CF_CD_DIV2 0x00000000 /* backplane/2 */
#define CF_CD_DIV3 0x00000040 /* backplane/3 */
#define CF_CD_DIV4 0x00000080 /* backplane/4 */
#define CF_CE 0x00000100 /* clock enable */
#define CF_SB 0x00000200 /* size/bytestrobe (synch only) */
/* pcmcia_memwait */
#define PM_W0_MASK 0x0000003f /* waitcount0 */
#define PM_W1_MASK 0x00001f00 /* waitcount1 */
#define PM_W1_SHIFT 8
#define PM_W2_MASK 0x001f0000 /* waitcount2 */
#define PM_W2_SHIFT 16
#define PM_W3_MASK 0x1f000000 /* waitcount3 */
#define PM_W3_SHIFT 24
/* pcmcia_attrwait */
#define PA_W0_MASK 0x0000003f /* waitcount0 */
#define PA_W1_MASK 0x00001f00 /* waitcount1 */
#define PA_W1_SHIFT 8
#define PA_W2_MASK 0x001f0000 /* waitcount2 */
#define PA_W2_SHIFT 16
#define PA_W3_MASK 0x1f000000 /* waitcount3 */
#define PA_W3_SHIFT 24
/* pcmcia_iowait */
#define PI_W0_MASK 0x0000003f /* waitcount0 */
#define PI_W1_MASK 0x00001f00 /* waitcount1 */
#define PI_W1_SHIFT 8
#define PI_W2_MASK 0x001f0000 /* waitcount2 */
#define PI_W2_SHIFT 16
#define PI_W3_MASK 0x1f000000 /* waitcount3 */
#define PI_W3_SHIFT 24
/* prog_waitcount */
#define PW_W0_MASK 0x0000001f /* waitcount0 */
#define PW_W1_MASK 0x00001f00 /* waitcount1 */
#define PW_W1_SHIFT 8
#define PW_W2_MASK 0x001f0000 /* waitcount2 */
#define PW_W2_SHIFT 16
#define PW_W3_MASK 0x1f000000 /* waitcount3 */
#define PW_W3_SHIFT 24
#define PW_W0 0x0000000c
#define PW_W1 0x00000a00
#define PW_W2 0x00020000
#define PW_W3 0x01000000
/* flash_waitcount */
#define FW_W0_MASK 0x0000003f /* waitcount0 */
#define FW_W1_MASK 0x00001f00 /* waitcount1 */
#define FW_W1_SHIFT 8
#define FW_W2_MASK 0x001f0000 /* waitcount2 */
#define FW_W2_SHIFT 16
#define FW_W3_MASK 0x1f000000 /* waitcount3 */
#define FW_W3_SHIFT 24
/* When Srom support present, fields in sromcontrol */
#define SRC_START 0x80000000
#define SRC_BUSY 0x80000000
#define SRC_OPCODE 0x60000000
#define SRC_OP_READ 0x00000000
#define SRC_OP_WRITE 0x20000000
#define SRC_OP_WRDIS 0x40000000
#define SRC_OP_WREN 0x60000000
#define SRC_OTPSEL 0x00000010
#define SRC_OTPPRESENT 0x00000020
#define SRC_LOCK 0x00000008
#define SRC_SIZE_MASK 0x00000006
#define SRC_SIZE_1K 0x00000000
#define SRC_SIZE_4K 0x00000002
#define SRC_SIZE_16K 0x00000004
#define SRC_SIZE_SHIFT 1
#define SRC_PRESENT 0x00000001
/* Fields in pmucontrol */
#define PCTL_ILP_DIV_MASK 0xffff0000
#define PCTL_ILP_DIV_SHIFT 16
#define PCTL_LQ_REQ_EN 0x00008000
#define PCTL_PLL_PLLCTL_UPD 0x00000400 /* rev 2 */
#define PCTL_NOILP_ON_WAIT 0x00000200 /* rev 1 */
#define PCTL_HT_REQ_EN 0x00000100
#define PCTL_ALP_REQ_EN 0x00000080
#define PCTL_XTALFREQ_MASK 0x0000007c
#define PCTL_XTALFREQ_SHIFT 2
#define PCTL_ILP_DIV_EN 0x00000002
#define PCTL_LPO_SEL 0x00000001
/* Retention Control */
#define PMU_RCTL_CLK_DIV_SHIFT 0
#define PMU_RCTL_CHAIN_LEN_SHIFT 12
#define PMU_RCTL_MACPHY_DISABLE_SHIFT 26
#define PMU_RCTL_MACPHY_DISABLE_MASK (1 << 26)
#define PMU_RCTL_LOGIC_DISABLE_SHIFT 27
#define PMU_RCTL_LOGIC_DISABLE_MASK (1 << 27)
#define PMU_RCTL_MEMSLP_LOG_SHIFT 28
#define PMU_RCTL_MEMSLP_LOG_MASK (1 << 28)
#define PMU_RCTL_MEMRETSLP_LOG_SHIFT 29
#define PMU_RCTL_MEMRETSLP_LOG_MASK (1 << 29)
/* Retention Group Control */
#define PMU_RCTLGRP_CHAIN_LEN_SHIFT 0
#define PMU_RCTLGRP_RMODE_ENABLE_SHIFT 14
#define PMU_RCTLGRP_RMODE_ENABLE_MASK (1 << 14)
#define PMU_RCTLGRP_DFT_ENABLE_SHIFT 15
#define PMU_RCTLGRP_DFT_ENABLE_MASK (1 << 15)
#define PMU_RCTLGRP_NSRST_DISABLE_SHIFT 16
#define PMU_RCTLGRP_NSRST_DISABLE_MASK (1 << 16)
/* Retention Group Control special for 4334 */
#define PMU4334_RCTLGRP_CHAIN_LEN_GRP0 338
#define PMU4334_RCTLGRP_CHAIN_LEN_GRP1 315
/* Retention Group Control special for 43341 */
#define PMU43341_RCTLGRP_CHAIN_LEN_GRP0 366
#define PMU43341_RCTLGRP_CHAIN_LEN_GRP1 330
/* Fields in clkstretch */
#define CSTRETCH_HT 0xffff0000
#define CSTRETCH_ALP 0x0000ffff
/* gpiotimerval */
#define GPIO_ONTIME_SHIFT 16
/* clockcontrol_n */
#define CN_N1_MASK 0x3f /* n1 control */
#define CN_N2_MASK 0x3f00 /* n2 control */
#define CN_N2_SHIFT 8
#define CN_PLLC_MASK 0xf0000 /* pll control */
#define CN_PLLC_SHIFT 16
/* clockcontrol_sb/pci/uart */
#define CC_M1_MASK 0x3f /* m1 control */
#define CC_M2_MASK 0x3f00 /* m2 control */
#define CC_M2_SHIFT 8
#define CC_M3_MASK 0x3f0000 /* m3 control */
#define CC_M3_SHIFT 16
#define CC_MC_MASK 0x1f000000 /* mux control */
#define CC_MC_SHIFT 24
/* N3M Clock control magic field values */
#define CC_F6_2 0x02 /* A factor of 2 in */
#define CC_F6_3 0x03 /* 6-bit fields like */
#define CC_F6_4 0x05 /* N1, M1 or M3 */
#define CC_F6_5 0x09
#define CC_F6_6 0x11
#define CC_F6_7 0x21
#define CC_F5_BIAS 5 /* 5-bit fields get this added */
#define CC_MC_BYPASS 0x08
#define CC_MC_M1 0x04
#define CC_MC_M1M2 0x02
#define CC_MC_M1M2M3 0x01
#define CC_MC_M1M3 0x11
/* Type 2 Clock control magic field values */
#define CC_T2_BIAS 2 /* n1, n2, m1 & m3 bias */
#define CC_T2M2_BIAS 3 /* m2 bias */
#define CC_T2MC_M1BYP 1
#define CC_T2MC_M2BYP 2
#define CC_T2MC_M3BYP 4
/* Type 6 Clock control magic field values */
#define CC_T6_MMASK 1 /* bits of interest in m */
#define CC_T6_M0 120000000 /* sb clock for m = 0 */
#define CC_T6_M1 100000000 /* sb clock for m = 1 */
#define SB2MIPS_T6(sb) (2 * (sb))
/* Common clock base */
#define CC_CLOCK_BASE1 24000000 /* Half the clock freq */
#define CC_CLOCK_BASE2 12500000 /* Alternate crystal on some PLLs */
/* Clock control values for 200MHz in 5350 */
#define CLKC_5350_N 0x0311
#define CLKC_5350_M 0x04020009
/* Flash types in the chipcommon capabilities register */
#define FLASH_NONE 0x000 /* No flash */
#define SFLASH_ST 0x100 /* ST serial flash */
#define SFLASH_AT 0x200 /* Atmel serial flash */
#define NFLASH 0x300
#define PFLASH 0x700 /* Parallel flash */
#define QSPIFLASH_ST 0x800
#define QSPIFLASH_AT 0x900
/* Bits in the ExtBus config registers */
#define CC_CFG_EN 0x0001 /* Enable */
#define CC_CFG_EM_MASK 0x000e /* Extif Mode */
#define CC_CFG_EM_ASYNC 0x0000 /* Async/Parallel flash */
#define CC_CFG_EM_SYNC 0x0002 /* Synchronous */
#define CC_CFG_EM_PCMCIA 0x0004 /* PCMCIA */
#define CC_CFG_EM_IDE 0x0006 /* IDE */
#define CC_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */
#define CC_CFG_CD_MASK 0x00e0 /* Sync: Clock divisor, rev >= 20 */
#define CC_CFG_CE 0x0100 /* Sync: Clock enable, rev >= 20 */
#define CC_CFG_SB 0x0200 /* Sync: Size/Bytestrobe, rev >= 20 */
#define CC_CFG_IS 0x0400 /* Extif Sync Clk Select, rev >= 20 */
/* ExtBus address space */
#define CC_EB_BASE 0x1a000000 /* Chipc ExtBus base address */
#define CC_EB_PCMCIA_MEM 0x1a000000 /* PCMCIA 0 memory base address */
#define CC_EB_PCMCIA_IO 0x1a200000 /* PCMCIA 0 I/O base address */
#define CC_EB_PCMCIA_CFG 0x1a400000 /* PCMCIA 0 config base address */
#define CC_EB_IDE 0x1a800000 /* IDE memory base */
#define CC_EB_PCMCIA1_MEM 0x1a800000 /* PCMCIA 1 memory base address */
#define CC_EB_PCMCIA1_IO 0x1aa00000 /* PCMCIA 1 I/O base address */
#define CC_EB_PCMCIA1_CFG 0x1ac00000 /* PCMCIA 1 config base address */
#define CC_EB_PROGIF 0x1b000000 /* ProgIF Async/Sync base address */
/* Start/busy bit in flashcontrol */
#define SFLASH_OPCODE 0x000000ff
#define SFLASH_ACTION 0x00000700
#define SFLASH_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */
#define SFLASH_START 0x80000000
#define SFLASH_BUSY SFLASH_START
/* flashcontrol action codes */
#define SFLASH_ACT_OPONLY 0x0000 /* Issue opcode only */
#define SFLASH_ACT_OP1D 0x0100 /* opcode + 1 data byte */
#define SFLASH_ACT_OP3A 0x0200 /* opcode + 3 addr bytes */
#define SFLASH_ACT_OP3A1D 0x0300 /* opcode + 3 addr & 1 data bytes */
#define SFLASH_ACT_OP3A4D 0x0400 /* opcode + 3 addr & 4 data bytes */
#define SFLASH_ACT_OP3A4X4D 0x0500 /* opcode + 3 addr, 4 don't care & 4 data bytes */
#define SFLASH_ACT_OP3A1X4D 0x0700 /* opcode + 3 addr, 1 don't care & 4 data bytes */
/* flashcontrol action+opcodes for ST flashes */
#define SFLASH_ST_WREN 0x0006 /* Write Enable */
#define SFLASH_ST_WRDIS 0x0004 /* Write Disable */
#define SFLASH_ST_RDSR 0x0105 /* Read Status Register */
#define SFLASH_ST_WRSR 0x0101 /* Write Status Register */
#define SFLASH_ST_READ 0x0303 /* Read Data Bytes */
#define SFLASH_ST_PP 0x0302 /* Page Program */
#define SFLASH_ST_SE 0x02d8 /* Sector Erase */
#define SFLASH_ST_BE 0x00c7 /* Bulk Erase */
#define SFLASH_ST_DP 0x00b9 /* Deep Power-down */
#define SFLASH_ST_RES 0x03ab /* Read Electronic Signature */
#define SFLASH_ST_CSA 0x1000 /* Keep chip select asserted */
#define SFLASH_ST_SSE 0x0220 /* Sub-sector Erase */
#define SFLASH_MXIC_RDID 0x0390 /* Read Manufacture ID */
#define SFLASH_MXIC_MFID 0xc2 /* MXIC Manufacture ID */
/* Status register bits for ST flashes */
#define SFLASH_ST_WIP 0x01 /* Write In Progress */
#define SFLASH_ST_WEL 0x02 /* Write Enable Latch */
#define SFLASH_ST_BP_MASK 0x1c /* Block Protect */
#define SFLASH_ST_BP_SHIFT 2
#define SFLASH_ST_SRWD 0x80 /* Status Register Write Disable */
/* flashcontrol action+opcodes for Atmel flashes */
#define SFLASH_AT_READ 0x07e8
#define SFLASH_AT_PAGE_READ 0x07d2
#define SFLASH_AT_BUF1_READ
#define SFLASH_AT_BUF2_READ
#define SFLASH_AT_STATUS 0x01d7
#define SFLASH_AT_BUF1_WRITE 0x0384
#define SFLASH_AT_BUF2_WRITE 0x0387
#define SFLASH_AT_BUF1_ERASE_PROGRAM 0x0283
#define SFLASH_AT_BUF2_ERASE_PROGRAM 0x0286
#define SFLASH_AT_BUF1_PROGRAM 0x0288
#define SFLASH_AT_BUF2_PROGRAM 0x0289
#define SFLASH_AT_PAGE_ERASE 0x0281
#define SFLASH_AT_BLOCK_ERASE 0x0250
#define SFLASH_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382
#define SFLASH_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385
#define SFLASH_AT_BUF1_LOAD 0x0253
#define SFLASH_AT_BUF2_LOAD 0x0255
#define SFLASH_AT_BUF1_COMPARE 0x0260
#define SFLASH_AT_BUF2_COMPARE 0x0261
#define SFLASH_AT_BUF1_REPROGRAM 0x0258
#define SFLASH_AT_BUF2_REPROGRAM 0x0259
/* Status register bits for Atmel flashes */
#define SFLASH_AT_READY 0x80
#define SFLASH_AT_MISMATCH 0x40
#define SFLASH_AT_ID_MASK 0x38
#define SFLASH_AT_ID_SHIFT 3
/* SPI register bits, corerev >= 37 */
#define GSIO_START 0x80000000
#define GSIO_BUSY GSIO_START
/*
* These are the UART port assignments, expressed as offsets from the base
* register. These assignments should hold for any serial port based on
* a 8250, 16450, or 16550(A).
*/
#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
#define UART_IER 1 /* In/Out: Interrupt Enable Register (DLAB=0) */
#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */
#define UART_IIR 2 /* In: Interrupt Identity Register */
#define UART_FCR 2 /* Out: FIFO Control Register */
#define UART_LCR 3 /* Out: Line Control Register */
#define UART_MCR 4 /* Out: Modem Control Register */
#define UART_LSR 5 /* In: Line Status Register */
#define UART_MSR 6 /* In: Modem Status Register */
#define UART_SCR 7 /* I/O: Scratch Register */
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
#define UART_LCR_WLEN8 0x03 /* Word length: 8 bits */
#define UART_MCR_OUT2 0x08 /* MCR GPIO out 2 */
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART_LSR_RX_FIFO 0x80 /* Receive FIFO error */
#define UART_LSR_TDHR 0x40 /* Data-hold-register empty */
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
#define UART_LSR_BREAK 0x10 /* Break interrupt */
#define UART_LSR_FRAMING 0x08 /* Framing error */
#define UART_LSR_PARITY 0x04 /* Parity error */
#define UART_LSR_OVERRUN 0x02 /* Overrun error */
#define UART_LSR_RXRDY 0x01 /* Receiver ready */
#define UART_FCR_FIFO_ENABLE 1 /* FIFO control register bit controlling FIFO enable/disable */
/* Interrupt Identity Register (IIR) bits */
#define UART_IIR_FIFO_MASK 0xc0 /* IIR FIFO disable/enabled mask */
#define UART_IIR_INT_MASK 0xf /* IIR interrupt ID source */
#define UART_IIR_MDM_CHG 0x0 /* Modem status changed */
#define UART_IIR_NOINT 0x1 /* No interrupt pending */
#define UART_IIR_THRE 0x2 /* THR empty */
#define UART_IIR_RCVD_DATA 0x4 /* Received data available */
#define UART_IIR_RCVR_STATUS 0x6 /* Receiver status */
#define UART_IIR_CHAR_TIME 0xc /* Character time */
/* Interrupt Enable Register (IER) bits */
#define UART_IER_PTIME 128 /* Programmable THRE Interrupt Mode Enable */
#define UART_IER_EDSSI 8 /* enable modem status interrupt */
#define UART_IER_ELSI 4 /* enable receiver line status interrupt */
#define UART_IER_ETBEI 2 /* enable transmitter holding register empty interrupt */
#define UART_IER_ERBFI 1 /* enable data available interrupt */
/* pmustatus */
#define PST_SLOW_WR_PENDING 0x0400
#define PST_EXTLPOAVAIL 0x0100
#define PST_WDRESET 0x0080
#define PST_INTPEND 0x0040
#define PST_SBCLKST 0x0030
#define PST_SBCLKST_ILP 0x0010
#define PST_SBCLKST_ALP 0x0020
#define PST_SBCLKST_HT 0x0030
#define PST_ALPAVAIL 0x0008
#define PST_HTAVAIL 0x0004
#define PST_RESINIT 0x0003
/* pmucapabilities */
#define PCAP_REV_MASK 0x000000ff
#define PCAP_RC_MASK 0x00001f00
#define PCAP_RC_SHIFT 8
#define PCAP_TC_MASK 0x0001e000
#define PCAP_TC_SHIFT 13
#define PCAP_PC_MASK 0x001e0000
#define PCAP_PC_SHIFT 17
#define PCAP_VC_MASK 0x01e00000
#define PCAP_VC_SHIFT 21
#define PCAP_CC_MASK 0x1e000000
#define PCAP_CC_SHIFT 25
#define PCAP5_PC_MASK 0x003e0000 /* PMU corerev >= 5 */
#define PCAP5_PC_SHIFT 17
#define PCAP5_VC_MASK 0x07c00000
#define PCAP5_VC_SHIFT 22
#define PCAP5_CC_MASK 0xf8000000
#define PCAP5_CC_SHIFT 27
/* PMU Resource Request Timer registers */
/* This is based on PmuRev0 */
#define PRRT_TIME_MASK 0x03ff
#define PRRT_INTEN 0x0400
#define PRRT_REQ_ACTIVE 0x0800
#define PRRT_ALP_REQ 0x1000
#define PRRT_HT_REQ 0x2000
#define PRRT_HQ_REQ 0x4000
/* bit 0 of the PMU interrupt vector is asserted if this mask is enabled */
#define RSRC_INTR_MASK_TIMER_INT_0 1
/* PMU resource bit position */
#define PMURES_BIT(bit) (1 << (bit))
/* PMU resource number limit */
#define PMURES_MAX_RESNUM 30
/* PMU chip control0 register */
#define PMU_CHIPCTL0 0
#define PMU43143_CC0_SDIO_DRSTR_OVR (1 << 31) /* sdio drive strength override enable */
/* clock req types */
#define PMU_CC1_CLKREQ_TYPE_SHIFT 19
#define PMU_CC1_CLKREQ_TYPE_MASK (1 << PMU_CC1_CLKREQ_TYPE_SHIFT)
#define CLKREQ_TYPE_CONFIG_OPENDRAIN 0
#define CLKREQ_TYPE_CONFIG_PUSHPULL 1
/* PMU chip control1 register */
#define PMU_CHIPCTL1 1
#define PMU_CC1_RXC_DLL_BYPASS 0x00010000
#define PMU_CC1_ENABLE_BBPLL_PWR_DOWN 0x00000010
#define PMU_CC1_IF_TYPE_MASK 0x00000030
#define PMU_CC1_IF_TYPE_RMII 0x00000000
#define PMU_CC1_IF_TYPE_MII 0x00000010
#define PMU_CC1_IF_TYPE_RGMII 0x00000020
#define PMU_CC1_SW_TYPE_MASK 0x000000c0
#define PMU_CC1_SW_TYPE_EPHY 0x00000000
#define PMU_CC1_SW_TYPE_EPHYMII 0x00000040
#define PMU_CC1_SW_TYPE_EPHYRMII 0x00000080
#define PMU_CC1_SW_TYPE_RGMII 0x000000c0
/* PMU chip control2 register */
#define PMU_CHIPCTL2 2
#define PMU_CC2_FORCE_SUBCORE_PWR_SWITCH_ON (1 << 18)
#define PMU_CC2_FORCE_PHY_PWR_SWITCH_ON (1 << 19)
#define PMU_CC2_FORCE_VDDM_PWR_SWITCH_ON (1 << 20)
#define PMU_CC2_FORCE_MEMLPLDO_PWR_SWITCH_ON (1 << 21)
/* PMU chip control3 register */
#define PMU_CHIPCTL3 3
#define PMU_CC3_ENABLE_SDIO_WAKEUP_SHIFT 19
#define PMU_CC3_ENABLE_RF_SHIFT 22
#define PMU_CC3_RF_DISABLE_IVALUE_SHIFT 23
/* PMU chip control5 register */
#define PMU_CHIPCTL5 5
/* PMU chip control6 register */
#define PMU_CHIPCTL6 6
#define PMU_CC6_ENABLE_CLKREQ_WAKEUP (1 << 4)
#define PMU_CC6_ENABLE_PMU_WAKEUP_ALP (1 << 6)
/* PMU chip control7 register */
#define PMU_CHIPCTL7 7
#define PMU_CC7_ENABLE_L2REFCLKPAD_PWRDWN (1 << 25)
#define PMU_CC7_ENABLE_MDIO_RESET_WAR (1 << 27)
/* PMU corerev and chip specific PLL controls.
* PMU<rev>_PLL<num>_XX where <rev> is PMU corerev and <num> is an arbitrary number
* to differentiate different PLLs controlled by the same PMU rev.
*/
/* pllcontrol registers */
/* PDIV, div_phy, div_arm, div_adc, dith_sel, ioff, kpd_scale, lsb_sel, mash_sel, lf_c & lf_r */
#define PMU0_PLL0_PLLCTL0 0
#define PMU0_PLL0_PC0_PDIV_MASK 1
#define PMU0_PLL0_PC0_PDIV_FREQ 25000
#define PMU0_PLL0_PC0_DIV_ARM_MASK 0x00000038
#define PMU0_PLL0_PC0_DIV_ARM_SHIFT 3
#define PMU0_PLL0_PC0_DIV_ARM_BASE 8
/* PC0_DIV_ARM for PLLOUT_ARM */
#define PMU0_PLL0_PC0_DIV_ARM_110MHZ 0
#define PMU0_PLL0_PC0_DIV_ARM_97_7MHZ 1
#define PMU0_PLL0_PC0_DIV_ARM_88MHZ 2
#define PMU0_PLL0_PC0_DIV_ARM_80MHZ 3 /* Default */
#define PMU0_PLL0_PC0_DIV_ARM_73_3MHZ 4
#define PMU0_PLL0_PC0_DIV_ARM_67_7MHZ 5
#define PMU0_PLL0_PC0_DIV_ARM_62_9MHZ 6
#define PMU0_PLL0_PC0_DIV_ARM_58_6MHZ 7
/* Wildcard base, stop_mod, en_lf_tp, en_cal & lf_r2 */
#define PMU0_PLL0_PLLCTL1 1
#define PMU0_PLL0_PC1_WILD_INT_MASK 0xf0000000
#define PMU0_PLL0_PC1_WILD_INT_SHIFT 28
#define PMU0_PLL0_PC1_WILD_FRAC_MASK 0x0fffff00
#define PMU0_PLL0_PC1_WILD_FRAC_SHIFT 8
#define PMU0_PLL0_PC1_STOP_MOD 0x00000040
/* Wildcard base, vco_calvar, vco_swc, vco_var_selref, vso_ical & vco_sel_avdd */
#define PMU0_PLL0_PLLCTL2 2
#define PMU0_PLL0_PC2_WILD_INT_MASK 0xf
#define PMU0_PLL0_PC2_WILD_INT_SHIFT 4
/* pllcontrol registers */
/* ndiv_pwrdn, pwrdn_ch<x>, refcomp_pwrdn, dly_ch<x>, p1div, p2div, _bypass_sdmod */
#define PMU1_PLL0_PLLCTL0 0
#define PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000
#define PMU1_PLL0_PC0_P1DIV_SHIFT 20
#define PMU1_PLL0_PC0_P2DIV_MASK 0x0f000000
#define PMU1_PLL0_PC0_P2DIV_SHIFT 24
/* m<x>div */
#define PMU1_PLL0_PLLCTL1 1
#define PMU1_PLL0_PC1_M1DIV_MASK 0x000000ff
#define PMU1_PLL0_PC1_M1DIV_SHIFT 0
#define PMU1_PLL0_PC1_M2DIV_MASK 0x0000ff00
#define PMU1_PLL0_PC1_M2DIV_SHIFT 8
#define PMU1_PLL0_PC1_M3DIV_MASK 0x00ff0000
#define PMU1_PLL0_PC1_M3DIV_SHIFT 16
#define PMU1_PLL0_PC1_M4DIV_MASK 0xff000000
#define PMU1_PLL0_PC1_M4DIV_SHIFT 24
#define PMU1_PLL0_PC1_M4DIV_BY_9 9
#define PMU1_PLL0_PC1_M4DIV_BY_18 0x12
#define PMU1_PLL0_PC1_M4DIV_BY_36 0x24
#define PMU1_PLL0_PC1_M4DIV_BY_60 0x3C
#define DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT 8
#define DOT11MAC_880MHZ_CLK_DIVISOR_MASK (0xFF << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT)
#define DOT11MAC_880MHZ_CLK_DIVISOR_VAL (0xE << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT)
/* m<x>div, ndiv_dither_mfb, ndiv_mode, ndiv_int */
#define PMU1_PLL0_PLLCTL2 2
#define PMU1_PLL0_PC2_M5DIV_MASK 0x000000ff
#define PMU1_PLL0_PC2_M5DIV_SHIFT 0
#define PMU1_PLL0_PC2_M5DIV_BY_12 0xc
#define PMU1_PLL0_PC2_M5DIV_BY_18 0x12
#define PMU1_PLL0_PC2_M5DIV_BY_36 0x24
#define PMU1_PLL0_PC2_M6DIV_MASK 0x0000ff00
#define PMU1_PLL0_PC2_M6DIV_SHIFT 8
#define PMU1_PLL0_PC2_M6DIV_BY_18 0x12
#define PMU1_PLL0_PC2_M6DIV_BY_36 0x24
#define PMU1_PLL0_PC2_NDIV_MODE_MASK 0x000e0000
#define PMU1_PLL0_PC2_NDIV_MODE_SHIFT 17
#define PMU1_PLL0_PC2_NDIV_MODE_MASH 1
#define PMU1_PLL0_PC2_NDIV_MODE_MFB 2 /* recommended for 4319 */
#define PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000
#define PMU1_PLL0_PC2_NDIV_INT_SHIFT 20
/* ndiv_frac */
#define PMU1_PLL0_PLLCTL3 3
#define PMU1_PLL0_PC3_NDIV_FRAC_MASK 0x00ffffff
#define PMU1_PLL0_PC3_NDIV_FRAC_SHIFT 0
/* pll_ctrl */
#define PMU1_PLL0_PLLCTL4 4
/* pll_ctrl, vco_rng, clkdrive_ch<x> */
#define PMU1_PLL0_PLLCTL5 5
#define PMU1_PLL0_PC5_CLK_DRV_MASK 0xffffff00
#define PMU1_PLL0_PC5_CLK_DRV_SHIFT 8
#define PMU1_PLL0_PLLCTL6 6
#define PMU1_PLL0_PLLCTL7 7
#define PMU1_PLL0_PLLCTL8 8
#define PMU1_PLLCTL8_OPENLOOP_MASK 0x2
/* PMU rev 2 control words */
#define PMU2_PHY_PLL_PLLCTL 4
#define PMU2_SI_PLL_PLLCTL 10
/* PMU rev 2 */
/* pllcontrol registers */
/* ndiv_pwrdn, pwrdn_ch<x>, refcomp_pwrdn, dly_ch<x>, p1div, p2div, _bypass_sdmod */
#define PMU2_PLL_PLLCTL0 0
#define PMU2_PLL_PC0_P1DIV_MASK 0x00f00000
#define PMU2_PLL_PC0_P1DIV_SHIFT 20
#define PMU2_PLL_PC0_P2DIV_MASK 0x0f000000
#define PMU2_PLL_PC0_P2DIV_SHIFT 24
/* m<x>div */
#define PMU2_PLL_PLLCTL1 1
#define PMU2_PLL_PC1_M1DIV_MASK 0x000000ff
#define PMU2_PLL_PC1_M1DIV_SHIFT 0
#define PMU2_PLL_PC1_M2DIV_MASK 0x0000ff00
#define PMU2_PLL_PC1_M2DIV_SHIFT 8
#define PMU2_PLL_PC1_M3DIV_MASK 0x00ff0000
#define PMU2_PLL_PC1_M3DIV_SHIFT 16
#define PMU2_PLL_PC1_M4DIV_MASK 0xff000000
#define PMU2_PLL_PC1_M4DIV_SHIFT 24
/* m<x>div, ndiv_dither_mfb, ndiv_mode, ndiv_int */
#define PMU2_PLL_PLLCTL2 2
#define PMU2_PLL_PC2_M5DIV_MASK 0x000000ff
#define PMU2_PLL_PC2_M5DIV_SHIFT 0
#define PMU2_PLL_PC2_M6DIV_MASK 0x0000ff00
#define PMU2_PLL_PC2_M6DIV_SHIFT 8
#define PMU2_PLL_PC2_NDIV_MODE_MASK 0x000e0000
#define PMU2_PLL_PC2_NDIV_MODE_SHIFT 17
#define PMU2_PLL_PC2_NDIV_INT_MASK 0x1ff00000
#define PMU2_PLL_PC2_NDIV_INT_SHIFT 20
/* ndiv_frac */
#define PMU2_PLL_PLLCTL3 3
#define PMU2_PLL_PC3_NDIV_FRAC_MASK 0x00ffffff
#define PMU2_PLL_PC3_NDIV_FRAC_SHIFT 0
/* pll_ctrl */
#define PMU2_PLL_PLLCTL4 4
/* pll_ctrl, vco_rng, clkdrive_ch<x> */
#define PMU2_PLL_PLLCTL5 5
#define PMU2_PLL_PC5_CLKDRIVE_CH1_MASK 0x00000f00
#define PMU2_PLL_PC5_CLKDRIVE_CH1_SHIFT 8
#define PMU2_PLL_PC5_CLKDRIVE_CH2_MASK 0x0000f000
#define PMU2_PLL_PC5_CLKDRIVE_CH2_SHIFT 12
#define PMU2_PLL_PC5_CLKDRIVE_CH3_MASK 0x000f0000
#define PMU2_PLL_PC5_CLKDRIVE_CH3_SHIFT 16
#define PMU2_PLL_PC5_CLKDRIVE_CH4_MASK 0x00f00000
#define PMU2_PLL_PC5_CLKDRIVE_CH4_SHIFT 20
#define PMU2_PLL_PC5_CLKDRIVE_CH5_MASK 0x0f000000
#define PMU2_PLL_PC5_CLKDRIVE_CH5_SHIFT 24
#define PMU2_PLL_PC5_CLKDRIVE_CH6_MASK 0xf0000000
#define PMU2_PLL_PC5_CLKDRIVE_CH6_SHIFT 28
/* PMU rev 5 (& 6) */
#define PMU5_PLL_P1P2_OFF 0
#define PMU5_PLL_P1_MASK 0x0f000000
#define PMU5_PLL_P1_SHIFT 24
#define PMU5_PLL_P2_MASK 0x00f00000
#define PMU5_PLL_P2_SHIFT 20
#define PMU5_PLL_M14_OFF 1
#define PMU5_PLL_MDIV_MASK 0x000000ff
#define PMU5_PLL_MDIV_WIDTH 8
#define PMU5_PLL_NM5_OFF 2
#define PMU5_PLL_NDIV_MASK 0xfff00000
#define PMU5_PLL_NDIV_SHIFT 20
#define PMU5_PLL_NDIV_MODE_MASK 0x000e0000
#define PMU5_PLL_NDIV_MODE_SHIFT 17
#define PMU5_PLL_FMAB_OFF 3
#define PMU5_PLL_MRAT_MASK 0xf0000000
#define PMU5_PLL_MRAT_SHIFT 28
#define PMU5_PLL_ABRAT_MASK 0x08000000
#define PMU5_PLL_ABRAT_SHIFT 27
#define PMU5_PLL_FDIV_MASK 0x07ffffff
#define PMU5_PLL_PLLCTL_OFF 4
#define PMU5_PLL_PCHI_OFF 5
#define PMU5_PLL_PCHI_MASK 0x0000003f
/* pmu XtalFreqRatio */
#define PMU_XTALFREQ_REG_ILPCTR_MASK 0x00001FFF
#define PMU_XTALFREQ_REG_MEASURE_MASK 0x80000000
#define PMU_XTALFREQ_REG_MEASURE_SHIFT 31
/* Divider allocation in 4716/47162/5356/5357 */
#define PMU5_MAINPLL_CPU 1
#define PMU5_MAINPLL_MEM 2
#define PMU5_MAINPLL_SI 3
/* 4706 PMU */
#define PMU4706_MAINPLL_PLL0 0
#define PMU6_4706_PROCPLL_OFF 4 /* The CPU PLL */
#define PMU6_4706_PROC_P2DIV_MASK 0x000f0000
#define PMU6_4706_PROC_P2DIV_SHIFT 16
#define PMU6_4706_PROC_P1DIV_MASK 0x0000f000
#define PMU6_4706_PROC_P1DIV_SHIFT 12
#define PMU6_4706_PROC_NDIV_INT_MASK 0x00000ff8
#define PMU6_4706_PROC_NDIV_INT_SHIFT 3
#define PMU6_4706_PROC_NDIV_MODE_MASK 0x00000007
#define PMU6_4706_PROC_NDIV_MODE_SHIFT 0
#define PMU7_PLL_PLLCTL7 7
#define PMU7_PLL_CTL7_M4DIV_MASK 0xff000000
#define PMU7_PLL_CTL7_M4DIV_SHIFT 24
#define PMU7_PLL_CTL7_M4DIV_BY_6 6
#define PMU7_PLL_CTL7_M4DIV_BY_12 0xc
#define PMU7_PLL_CTL7_M4DIV_BY_24 0x18
#define PMU7_PLL_PLLCTL8 8
#define PMU7_PLL_CTL8_M5DIV_MASK 0x000000ff
#define PMU7_PLL_CTL8_M5DIV_SHIFT 0
#define PMU7_PLL_CTL8_M5DIV_BY_8 8
#define PMU7_PLL_CTL8_M5DIV_BY_12 0xc
#define PMU7_PLL_CTL8_M5DIV_BY_24 0x18
#define PMU7_PLL_CTL8_M6DIV_MASK 0x0000ff00
#define PMU7_PLL_CTL8_M6DIV_SHIFT 8
#define PMU7_PLL_CTL8_M6DIV_BY_12 0xc
#define PMU7_PLL_CTL8_M6DIV_BY_24 0x18
#define PMU7_PLL_PLLCTL11 11
#define PMU7_PLL_PLLCTL11_MASK 0xffffff00
#define PMU7_PLL_PLLCTL11_VAL 0x22222200
/* PMU rev 15 */
#define PMU15_PLL_PLLCTL0 0
#define PMU15_PLL_PC0_CLKSEL_MASK 0x00000003
#define PMU15_PLL_PC0_CLKSEL_SHIFT 0
#define PMU15_PLL_PC0_FREQTGT_MASK 0x003FFFFC
#define PMU15_PLL_PC0_FREQTGT_SHIFT 2
#define PMU15_PLL_PC0_PRESCALE_MASK 0x00C00000
#define PMU15_PLL_PC0_PRESCALE_SHIFT 22
#define PMU15_PLL_PC0_KPCTRL_MASK 0x07000000
#define PMU15_PLL_PC0_KPCTRL_SHIFT 24
#define PMU15_PLL_PC0_FCNTCTRL_MASK 0x38000000
#define PMU15_PLL_PC0_FCNTCTRL_SHIFT 27
#define PMU15_PLL_PC0_FDCMODE_MASK 0x40000000
#define PMU15_PLL_PC0_FDCMODE_SHIFT 30
#define PMU15_PLL_PC0_CTRLBIAS_MASK 0x80000000
#define PMU15_PLL_PC0_CTRLBIAS_SHIFT 31
#define PMU15_PLL_PLLCTL1 1
#define PMU15_PLL_PC1_BIAS_CTLM_MASK 0x00000060
#define PMU15_PLL_PC1_BIAS_CTLM_SHIFT 5
#define PMU15_PLL_PC1_BIAS_CTLM_RST_MASK 0x00000040
#define PMU15_PLL_PC1_BIAS_CTLM_RST_SHIFT 6
#define PMU15_PLL_PC1_BIAS_SS_DIVR_MASK 0x0001FF80
#define PMU15_PLL_PC1_BIAS_SS_DIVR_SHIFT 7
#define PMU15_PLL_PC1_BIAS_SS_RSTVAL_MASK 0x03FE0000
#define PMU15_PLL_PC1_BIAS_SS_RSTVAL_SHIFT 17
#define PMU15_PLL_PC1_BIAS_INTG_BW_MASK 0x0C000000
#define PMU15_PLL_PC1_BIAS_INTG_BW_SHIFT 26
#define PMU15_PLL_PC1_BIAS_INTG_BYP_MASK 0x10000000
#define PMU15_PLL_PC1_BIAS_INTG_BYP_SHIFT 28
#define PMU15_PLL_PC1_OPENLP_EN_MASK 0x40000000
#define PMU15_PLL_PC1_OPENLP_EN_SHIFT 30
#define PMU15_PLL_PLLCTL2 2
#define PMU15_PLL_PC2_CTEN_MASK 0x00000001
#define PMU15_PLL_PC2_CTEN_SHIFT 0
#define PMU15_PLL_PLLCTL3 3
#define PMU15_PLL_PC3_DITHER_EN_MASK 0x00000001
#define PMU15_PLL_PC3_DITHER_EN_SHIFT 0
#define PMU15_PLL_PC3_DCOCTLSP_MASK 0xFE000000
#define PMU15_PLL_PC3_DCOCTLSP_SHIFT 25
#define PMU15_PLL_PC3_DCOCTLSP_DIV2EN_MASK 0x01
#define PMU15_PLL_PC3_DCOCTLSP_DIV2EN_SHIFT 0
#define PMU15_PLL_PC3_DCOCTLSP_CH0EN_MASK 0x02
#define PMU15_PLL_PC3_DCOCTLSP_CH0EN_SHIFT 1
#define PMU15_PLL_PC3_DCOCTLSP_CH1EN_MASK 0x04
#define PMU15_PLL_PC3_DCOCTLSP_CH1EN_SHIFT 2
#define PMU15_PLL_PC3_DCOCTLSP_CH0SEL_MASK 0x18
#define PMU15_PLL_PC3_DCOCTLSP_CH0SEL_SHIFT 3
#define PMU15_PLL_PC3_DCOCTLSP_CH1SEL_MASK 0x60
#define PMU15_PLL_PC3_DCOCTLSP_CH1SEL_SHIFT 5
#define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV1 0
#define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV2 1
#define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV3 2
#define PMU15_PLL_PC3_DCOCTLSP_CHSEL_OUTP_DIV5 3
#define PMU15_PLL_PLLCTL4 4
#define PMU15_PLL_PC4_FLLCLK1_DIV_MASK 0x00000007
#define PMU15_PLL_PC4_FLLCLK1_DIV_SHIFT 0
#define PMU15_PLL_PC4_FLLCLK2_DIV_MASK 0x00000038
#define PMU15_PLL_PC4_FLLCLK2_DIV_SHIFT 3
#define PMU15_PLL_PC4_FLLCLK3_DIV_MASK 0x000001C0
#define PMU15_PLL_PC4_FLLCLK3_DIV_SHIFT 6
#define PMU15_PLL_PC4_DBGMODE_MASK 0x00000E00
#define PMU15_PLL_PC4_DBGMODE_SHIFT 9
#define PMU15_PLL_PC4_FLL480_CTLSP_LK_MASK 0x00001000
#define PMU15_PLL_PC4_FLL480_CTLSP_LK_SHIFT 12
#define PMU15_PLL_PC4_FLL480_CTLSP_MASK 0x000FE000
#define PMU15_PLL_PC4_FLL480_CTLSP_SHIFT 13
#define PMU15_PLL_PC4_DINPOL_MASK 0x00100000
#define PMU15_PLL_PC4_DINPOL_SHIFT 20
#define PMU15_PLL_PC4_CLKOUT_PD_MASK 0x00200000
#define PMU15_PLL_PC4_CLKOUT_PD_SHIFT 21
#define PMU15_PLL_PC4_CLKDIV2_PD_MASK 0x00400000
#define PMU15_PLL_PC4_CLKDIV2_PD_SHIFT 22
#define PMU15_PLL_PC4_CLKDIV4_PD_MASK 0x00800000
#define PMU15_PLL_PC4_CLKDIV4_PD_SHIFT 23
#define PMU15_PLL_PC4_CLKDIV8_PD_MASK 0x01000000
#define PMU15_PLL_PC4_CLKDIV8_PD_SHIFT 24
#define PMU15_PLL_PC4_CLKDIV16_PD_MASK 0x02000000
#define PMU15_PLL_PC4_CLKDIV16_PD_SHIFT 25
#define PMU15_PLL_PC4_TEST_EN_MASK 0x04000000
#define PMU15_PLL_PC4_TEST_EN_SHIFT 26
#define PMU15_PLL_PLLCTL5 5
#define PMU15_PLL_PC5_FREQTGT_MASK 0x000FFFFF
#define PMU15_PLL_PC5_FREQTGT_SHIFT 0
#define PMU15_PLL_PC5_DCOCTLSP_MASK 0x07F00000
#define PMU15_PLL_PC5_DCOCTLSP_SHIFT 20
#define PMU15_PLL_PC5_PRESCALE_MASK 0x18000000
#define PMU15_PLL_PC5_PRESCALE_SHIFT 27
#define PMU15_PLL_PLLCTL6 6
#define PMU15_PLL_PC6_FREQTGT_MASK 0x000FFFFF
#define PMU15_PLL_PC6_FREQTGT_SHIFT 0
#define PMU15_PLL_PC6_DCOCTLSP_MASK 0x07F00000
#define PMU15_PLL_PC6_DCOCTLSP_SHIFT 20
#define PMU15_PLL_PC6_PRESCALE_MASK 0x18000000
#define PMU15_PLL_PC6_PRESCALE_SHIFT 27
#define PMU15_FREQTGT_480_DEFAULT 0x19AB1
#define PMU15_FREQTGT_492_DEFAULT 0x1A4F5
#define PMU15_ARM_96MHZ 96000000 /* 96 Mhz */
#define PMU15_ARM_98MHZ 98400000 /* 98.4 Mhz */
#define PMU15_ARM_97MHZ 97000000 /* 97 Mhz */
#define PMU17_PLLCTL2_NDIVTYPE_MASK 0x00000070
#define PMU17_PLLCTL2_NDIVTYPE_SHIFT 4
#define PMU17_PLLCTL2_NDIV_MODE_INT 0
#define PMU17_PLLCTL2_NDIV_MODE_INT1B8 1
#define PMU17_PLLCTL2_NDIV_MODE_MASH111 2
#define PMU17_PLLCTL2_NDIV_MODE_MASH111B8 3
#define PMU17_PLLCTL0_BBPLL_PWRDWN 0
#define PMU17_PLLCTL0_BBPLL_DRST 3
#define PMU17_PLLCTL0_BBPLL_DISBL_CLK 8
/* PLL usage in 4716/47162 */
#define PMU4716_MAINPLL_PLL0 12
/* PLL usage in 4335 */
#define PMU4335_PLL0_PC2_P1DIV_MASK 0x000f0000
#define PMU4335_PLL0_PC2_P1DIV_SHIFT 16
#define PMU4335_PLL0_PC2_NDIV_INT_MASK 0xff800000
#define PMU4335_PLL0_PC2_NDIV_INT_SHIFT 23
#define PMU4335_PLL0_PC1_MDIV2_MASK 0x0000ff00
#define PMU4335_PLL0_PC1_MDIV2_SHIFT 8
/* PLL usage in 5356/5357 */
#define PMU5356_MAINPLL_PLL0 0
#define PMU5357_MAINPLL_PLL0 0
/* 4716/47162 resources */
#define RES4716_PROC_PLL_ON 0x00000040
#define RES4716_PROC_HT_AVAIL 0x00000080
/* 4716/4717/4718 Chip specific ChipControl register bits */
#define CCTRL_471X_I2S_PINS_ENABLE 0x0080 /* I2S pins off by default, shared w/ pflash */
/* 5357 Chip specific ChipControl register bits */
/* 2nd - 32-bit reg */
#define CCTRL_5357_I2S_PINS_ENABLE 0x00040000 /* I2S pins enable */
#define CCTRL_5357_I2CSPI_PINS_ENABLE 0x00080000 /* I2C/SPI pins enable */
/* 5354 resources */
#define RES5354_EXT_SWITCHER_PWM 0 /* 0x00001 */
#define RES5354_BB_SWITCHER_PWM 1 /* 0x00002 */
#define RES5354_BB_SWITCHER_BURST 2 /* 0x00004 */
#define RES5354_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */
#define RES5354_ILP_REQUEST 4 /* 0x00010 */
#define RES5354_RADIO_SWITCHER_PWM 5 /* 0x00020 */
#define RES5354_RADIO_SWITCHER_BURST 6 /* 0x00040 */
#define RES5354_ROM_SWITCH 7 /* 0x00080 */
#define RES5354_PA_REF_LDO 8 /* 0x00100 */
#define RES5354_RADIO_LDO 9 /* 0x00200 */
#define RES5354_AFE_LDO 10 /* 0x00400 */
#define RES5354_PLL_LDO 11 /* 0x00800 */
#define RES5354_BG_FILTBYP 12 /* 0x01000 */
#define RES5354_TX_FILTBYP 13 /* 0x02000 */
#define RES5354_RX_FILTBYP 14 /* 0x04000 */
#define RES5354_XTAL_PU 15 /* 0x08000 */
#define RES5354_XTAL_EN 16 /* 0x10000 */
#define RES5354_BB_PLL_FILTBYP 17 /* 0x20000 */
#define RES5354_RF_PLL_FILTBYP 18 /* 0x40000 */
#define RES5354_BB_PLL_PU 19 /* 0x80000 */
/* 5357 Chip specific ChipControl register bits */
#define CCTRL5357_EXTPA (1<<14) /* extPA in ChipControl 1, bit 14 */
#define CCTRL5357_ANT_MUX_2o3 (1<<15) /* 2o3 in ChipControl 1, bit 15 */
#define CCTRL5357_NFLASH (1<<16) /* Nandflash in ChipControl 1, bit 16 */
/* 43217 Chip specific ChipControl register bits */
#define CCTRL43217_EXTPA_C0 (1<<13) /* core0 extPA in ChipControl 1, bit 13 */
#define CCTRL43217_EXTPA_C1 (1<<8) /* core1 extPA in ChipControl 1, bit 8 */
/* 43228 Chip specific ChipControl register bits */
#define CCTRL43228_EXTPA_C0 (1<<14) /* core1 extPA in ChipControl 1, bit 14 */
#define CCTRL43228_EXTPA_C1 (1<<9) /* core0 extPA in ChipControl 1, bit 1 */
/* 4328 resources */
#define RES4328_EXT_SWITCHER_PWM 0 /* 0x00001 */
#define RES4328_BB_SWITCHER_PWM 1 /* 0x00002 */
#define RES4328_BB_SWITCHER_BURST 2 /* 0x00004 */
#define RES4328_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */
#define RES4328_ILP_REQUEST 4 /* 0x00010 */
#define RES4328_RADIO_SWITCHER_PWM 5 /* 0x00020 */
#define RES4328_RADIO_SWITCHER_BURST 6 /* 0x00040 */
#define RES4328_ROM_SWITCH 7 /* 0x00080 */
#define RES4328_PA_REF_LDO 8 /* 0x00100 */
#define RES4328_RADIO_LDO 9 /* 0x00200 */
#define RES4328_AFE_LDO 10 /* 0x00400 */
#define RES4328_PLL_LDO 11 /* 0x00800 */
#define RES4328_BG_FILTBYP 12 /* 0x01000 */
#define RES4328_TX_FILTBYP 13 /* 0x02000 */
#define RES4328_RX_FILTBYP 14 /* 0x04000 */
#define RES4328_XTAL_PU 15 /* 0x08000 */
#define RES4328_XTAL_EN 16 /* 0x10000 */
#define RES4328_BB_PLL_FILTBYP 17 /* 0x20000 */
#define RES4328_RF_PLL_FILTBYP 18 /* 0x40000 */
#define RES4328_BB_PLL_PU 19 /* 0x80000 */
/* 4325 A0/A1 resources */
#define RES4325_BUCK_BOOST_BURST 0 /* 0x00000001 */
#define RES4325_CBUCK_BURST 1 /* 0x00000002 */
#define RES4325_CBUCK_PWM 2 /* 0x00000004 */
#define RES4325_CLDO_CBUCK_BURST 3 /* 0x00000008 */
#define RES4325_CLDO_CBUCK_PWM 4 /* 0x00000010 */
#define RES4325_BUCK_BOOST_PWM 5 /* 0x00000020 */
#define RES4325_ILP_REQUEST 6 /* 0x00000040 */
#define RES4325_ABUCK_BURST 7 /* 0x00000080 */
#define RES4325_ABUCK_PWM 8 /* 0x00000100 */
#define RES4325_LNLDO1_PU 9 /* 0x00000200 */
#define RES4325_OTP_PU 10 /* 0x00000400 */
#define RES4325_LNLDO3_PU 11 /* 0x00000800 */
#define RES4325_LNLDO4_PU 12 /* 0x00001000 */
#define RES4325_XTAL_PU 13 /* 0x00002000 */
#define RES4325_ALP_AVAIL 14 /* 0x00004000 */
#define RES4325_RX_PWRSW_PU 15 /* 0x00008000 */
#define RES4325_TX_PWRSW_PU 16 /* 0x00010000 */
#define RES4325_RFPLL_PWRSW_PU 17 /* 0x00020000 */
#define RES4325_LOGEN_PWRSW_PU 18 /* 0x00040000 */
#define RES4325_AFE_PWRSW_PU 19 /* 0x00080000 */
#define RES4325_BBPLL_PWRSW_PU 20 /* 0x00100000 */
#define RES4325_HT_AVAIL 21 /* 0x00200000 */
/* 4325 B0/C0 resources */
#define RES4325B0_CBUCK_LPOM 1 /* 0x00000002 */
#define RES4325B0_CBUCK_BURST 2 /* 0x00000004 */
#define RES4325B0_CBUCK_PWM 3 /* 0x00000008 */
#define RES4325B0_CLDO_PU 4 /* 0x00000010 */
/* 4325 C1 resources */
#define RES4325C1_LNLDO2_PU 12 /* 0x00001000 */
/* 4325 chip-specific ChipStatus register bits */
#define CST4325_SPROM_OTP_SEL_MASK 0x00000003
#define CST4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
#define CST4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
#define CST4325_OTP_SEL 2 /* OTP is powered up, no SPROM */
#define CST4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
#define CST4325_SDIO_USB_MODE_MASK 0x00000004
#define CST4325_SDIO_USB_MODE_SHIFT 2
#define CST4325_RCAL_VALID_MASK 0x00000008
#define CST4325_RCAL_VALID_SHIFT 3
#define CST4325_RCAL_VALUE_MASK 0x000001f0
#define CST4325_RCAL_VALUE_SHIFT 4
#define CST4325_PMUTOP_2B_MASK 0x00000200 /* 1 for 2b, 0 for to 2a */
#define CST4325_PMUTOP_2B_SHIFT 9
#define RES4329_RESERVED0 0 /* 0x00000001 */
#define RES4329_CBUCK_LPOM 1 /* 0x00000002 */
#define RES4329_CBUCK_BURST 2 /* 0x00000004 */
#define RES4329_CBUCK_PWM 3 /* 0x00000008 */
#define RES4329_CLDO_PU 4 /* 0x00000010 */
#define RES4329_PALDO_PU 5 /* 0x00000020 */
#define RES4329_ILP_REQUEST 6 /* 0x00000040 */
#define RES4329_RESERVED7 7 /* 0x00000080 */
#define RES4329_RESERVED8 8 /* 0x00000100 */
#define RES4329_LNLDO1_PU 9 /* 0x00000200 */
#define RES4329_OTP_PU 10 /* 0x00000400 */
#define RES4329_RESERVED11 11 /* 0x00000800 */
#define RES4329_LNLDO2_PU 12 /* 0x00001000 */
#define RES4329_XTAL_PU 13 /* 0x00002000 */
#define RES4329_ALP_AVAIL 14 /* 0x00004000 */
#define RES4329_RX_PWRSW_PU 15 /* 0x00008000 */
#define RES4329_TX_PWRSW_PU 16 /* 0x00010000 */
#define RES4329_RFPLL_PWRSW_PU 17 /* 0x00020000 */
#define RES4329_LOGEN_PWRSW_PU 18 /* 0x00040000 */
#define RES4329_AFE_PWRSW_PU 19 /* 0x00080000 */
#define RES4329_BBPLL_PWRSW_PU 20 /* 0x00100000 */
#define RES4329_HT_AVAIL 21 /* 0x00200000 */
#define CST4329_SPROM_OTP_SEL_MASK 0x00000003
#define CST4329_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
#define CST4329_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
#define CST4329_OTP_SEL 2 /* OTP is powered up, no SPROM */
#define CST4329_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
#define CST4329_SPI_SDIO_MODE_MASK 0x00000004
#define CST4329_SPI_SDIO_MODE_SHIFT 2
/* 4312 chip-specific ChipStatus register bits */
#define CST4312_SPROM_OTP_SEL_MASK 0x00000003
#define CST4312_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
#define CST4312_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
#define CST4312_OTP_SEL 2 /* OTP is powered up, no SPROM */
#define CST4312_OTP_BAD 3 /* OTP is broken, SPROM is present */
/* 4312 resources (all PMU chips with little memory constraint) */
#define RES4312_SWITCHER_BURST 0 /* 0x00000001 */
#define RES4312_SWITCHER_PWM 1 /* 0x00000002 */
#define RES4312_PA_REF_LDO 2 /* 0x00000004 */
#define RES4312_CORE_LDO_BURST 3 /* 0x00000008 */
#define RES4312_CORE_LDO_PWM 4 /* 0x00000010 */
#define RES4312_RADIO_LDO 5 /* 0x00000020 */
#define RES4312_ILP_REQUEST 6 /* 0x00000040 */
#define RES4312_BG_FILTBYP 7 /* 0x00000080 */
#define RES4312_TX_FILTBYP 8 /* 0x00000100 */
#define RES4312_RX_FILTBYP 9 /* 0x00000200 */
#define RES4312_XTAL_PU 10 /* 0x00000400 */
#define RES4312_ALP_AVAIL 11 /* 0x00000800 */
#define RES4312_BB_PLL_FILTBYP 12 /* 0x00001000 */
#define RES4312_RF_PLL_FILTBYP 13 /* 0x00002000 */
#define RES4312_HT_AVAIL 14 /* 0x00004000 */
/* 4322 resources */
#define RES4322_RF_LDO 0
#define RES4322_ILP_REQUEST 1
#define RES4322_XTAL_PU 2
#define RES4322_ALP_AVAIL 3
#define RES4322_SI_PLL_ON 4
#define RES4322_HT_SI_AVAIL 5
#define RES4322_PHY_PLL_ON 6
#define RES4322_HT_PHY_AVAIL 7
#define RES4322_OTP_PU 8
/* 4322 chip-specific ChipStatus register bits */
#define CST4322_XTAL_FREQ_20_40MHZ 0x00000020
#define CST4322_SPROM_OTP_SEL_MASK 0x000000c0
#define CST4322_SPROM_OTP_SEL_SHIFT 6
#define CST4322_NO_SPROM_OTP 0 /* no OTP, no SPROM */
#define CST4322_SPROM_PRESENT 1 /* SPROM is present */
#define CST4322_OTP_PRESENT 2 /* OTP is present */
#define CST4322_PCI_OR_USB 0x00000100
#define CST4322_BOOT_MASK 0x00000600
#define CST4322_BOOT_SHIFT 9
#define CST4322_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */
#define CST4322_BOOT_FROM_ROM 1 /* boot from ROM */
#define CST4322_BOOT_FROM_FLASH 2 /* boot from FLASH */
#define CST4322_BOOT_FROM_INVALID 3
#define CST4322_ILP_DIV_EN 0x00000800
#define CST4322_FLASH_TYPE_MASK 0x00001000
#define CST4322_FLASH_TYPE_SHIFT 12
#define CST4322_FLASH_TYPE_SHIFT_ST 0 /* ST serial FLASH */
#define CST4322_FLASH_TYPE_SHIFT_ATMEL 1 /* ATMEL flash */
#define CST4322_ARM_TAP_SEL 0x00002000
#define CST4322_RES_INIT_MODE_MASK 0x0000c000
#define CST4322_RES_INIT_MODE_SHIFT 14
#define CST4322_RES_INIT_MODE_ILPAVAIL 0 /* resinitmode: ILP available */
#define CST4322_RES_INIT_MODE_ILPREQ 1 /* resinitmode: ILP request */
#define CST4322_RES_INIT_MODE_ALPAVAIL 2 /* resinitmode: ALP available */
#define CST4322_RES_INIT_MODE_HTAVAIL 3 /* resinitmode: HT available */
#define CST4322_PCIPLLCLK_GATING 0x00010000
#define CST4322_CLK_SWITCH_PCI_TO_ALP 0x00020000
#define CST4322_PCI_CARDBUS_MODE 0x00040000
/* 43224 chip-specific ChipControl register bits */
#define CCTRL43224_GPIO_TOGGLE 0x8000 /* gpio[3:0] pins as btcoex or s/w gpio */
#define CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */
#define CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */
/* 43236 resources */
#define RES43236_REGULATOR 0
#define RES43236_ILP_REQUEST 1
#define RES43236_XTAL_PU 2
#define RES43236_ALP_AVAIL 3
#define RES43236_SI_PLL_ON 4
#define RES43236_HT_SI_AVAIL 5
/* 43236 chip-specific ChipControl register bits */
#define CCTRL43236_BT_COEXIST (1<<0) /* 0 disable */
#define CCTRL43236_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */
#define CCTRL43236_EXT_LNA (1<<2) /* 0 disable */
#define CCTRL43236_ANT_MUX_2o3 (1<<3) /* 2o3 mux, chipcontrol bit 3 */
#define CCTRL43236_GSIO (1<<4) /* 0 disable */
/* 43236 Chip specific ChipStatus register bits */
#define CST43236_SFLASH_MASK 0x00000040
#define CST43236_OTP_SEL_MASK 0x00000080
#define CST43236_OTP_SEL_SHIFT 7
#define CST43236_HSIC_MASK 0x00000100 /* USB/HSIC */
#define CST43236_BP_CLK 0x00000200 /* 120/96Mbps */
#define CST43236_BOOT_MASK 0x00001800
#define CST43236_BOOT_SHIFT 11
#define CST43236_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */
#define CST43236_BOOT_FROM_ROM 1 /* boot from ROM */
#define CST43236_BOOT_FROM_FLASH 2 /* boot from FLASH */
#define CST43236_BOOT_FROM_INVALID 3
/* 43237 resources */
#define RES43237_REGULATOR 0
#define RES43237_ILP_REQUEST 1
#define RES43237_XTAL_PU 2
#define RES43237_ALP_AVAIL 3
#define RES43237_SI_PLL_ON 4
#define RES43237_HT_SI_AVAIL 5
/* 43237 chip-specific ChipControl register bits */
#define CCTRL43237_BT_COEXIST (1<<0) /* 0 disable */
#define CCTRL43237_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */
#define CCTRL43237_EXT_LNA (1<<2) /* 0 disable */
#define CCTRL43237_ANT_MUX_2o3 (1<<3) /* 2o3 mux, chipcontrol bit 3 */
#define CCTRL43237_GSIO (1<<4) /* 0 disable */
/* 43237 Chip specific ChipStatus register bits */
#define CST43237_SFLASH_MASK 0x00000040
#define CST43237_OTP_SEL_MASK 0x00000080
#define CST43237_OTP_SEL_SHIFT 7
#define CST43237_HSIC_MASK 0x00000100 /* USB/HSIC */
#define CST43237_BP_CLK 0x00000200 /* 120/96Mbps */
#define CST43237_BOOT_MASK 0x00001800
#define CST43237_BOOT_SHIFT 11
#define CST43237_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */
#define CST43237_BOOT_FROM_ROM 1 /* boot from ROM */
#define CST43237_BOOT_FROM_FLASH 2 /* boot from FLASH */
#define CST43237_BOOT_FROM_INVALID 3
/* 43239 resources */
#define RES43239_OTP_PU 9
#define RES43239_MACPHY_CLKAVAIL 23
#define RES43239_HT_AVAIL 24
/* 43239 Chip specific ChipStatus register bits */
#define CST43239_SPROM_MASK 0x00000002
#define CST43239_SFLASH_MASK 0x00000004
#define CST43239_RES_INIT_MODE_SHIFT 7
#define CST43239_RES_INIT_MODE_MASK 0x000001f0
#define CST43239_CHIPMODE_SDIOD(cs) ((cs) & (1 << 15)) /* SDIO || gSPI */
#define CST43239_CHIPMODE_USB20D(cs) (~(cs) & (1 << 15)) /* USB || USBDA */
#define CST43239_CHIPMODE_SDIO(cs) (((cs) & (1 << 0)) == 0) /* SDIO */
#define CST43239_CHIPMODE_GSPI(cs) (((cs) & (1 << 0)) == (1 << 0)) /* gSPI */
/* 4324 resources */
/* 43242 use same PMU as 4324 */
#define RES4324_LPLDO_PU 0
#define RES4324_RESET_PULLDN_DIS 1
#define RES4324_PMU_BG_PU 2
#define RES4324_HSIC_LDO_PU 3
#define RES4324_CBUCK_LPOM_PU 4
#define RES4324_CBUCK_PFM_PU 5
#define RES4324_CLDO_PU 6
#define RES4324_LPLDO2_LVM 7
#define RES4324_LNLDO1_PU 8
#define RES4324_LNLDO2_PU 9
#define RES4324_LDO3P3_PU 10
#define RES4324_OTP_PU 11
#define RES4324_XTAL_PU 12
#define RES4324_BBPLL_PU 13
#define RES4324_LQ_AVAIL 14
#define RES4324_WL_CORE_READY 17
#define RES4324_ILP_REQ 18
#define RES4324_ALP_AVAIL 19
#define RES4324_PALDO_PU 20
#define RES4324_RADIO_PU 21
#define RES4324_SR_CLK_STABLE 22
#define RES4324_SR_SAVE_RESTORE 23
#define RES4324_SR_PHY_PWRSW 24
#define RES4324_SR_PHY_PIC 25
#define RES4324_SR_SUBCORE_PWRSW 26
#define RES4324_SR_SUBCORE_PIC 27
#define RES4324_SR_MEM_PM0 28
#define RES4324_HT_AVAIL 29
#define RES4324_MACPHY_CLKAVAIL 30
/* 4324 Chip specific ChipStatus register bits */
#define CST4324_SPROM_MASK 0x00000080
#define CST4324_SFLASH_MASK 0x00400000
#define CST4324_RES_INIT_MODE_SHIFT 10
#define CST4324_RES_INIT_MODE_MASK 0x00000c00
#define CST4324_CHIPMODE_MASK 0x7
#define CST4324_CHIPMODE_SDIOD(cs) ((~(cs)) & (1 << 2)) /* SDIO || gSPI */
#define CST4324_CHIPMODE_USB20D(cs) (((cs) & CST4324_CHIPMODE_MASK) == 0x6) /* USB || USBDA */
/* 43242 Chip specific ChipStatus register bits */
#define CST43242_SFLASH_MASK 0x00000008
#define CST43242_SR_HALT (1<<25)
#define CST43242_SR_CHIP_STATUS_2 27 /* bit 27 */
/* 4331 resources */
#define RES4331_REGULATOR 0
#define RES4331_ILP_REQUEST 1
#define RES4331_XTAL_PU 2
#define RES4331_ALP_AVAIL 3
#define RES4331_SI_PLL_ON 4
#define RES4331_HT_SI_AVAIL 5
/* 4331 chip-specific ChipControl register bits */
#define CCTRL4331_BT_COEXIST (1<<0) /* 0 disable */
#define CCTRL4331_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */
#define CCTRL4331_EXT_LNA_G (1<<2) /* 0 disable */
#define CCTRL4331_SPROM_GPIO13_15 (1<<3) /* sprom/gpio13-15 mux */
#define CCTRL4331_EXTPA_EN (1<<4) /* 0 ext pa disable, 1 ext pa enabled */
#define CCTRL4331_GPIOCLK_ON_SPROMCS (1<<5) /* set drive out GPIO_CLK on sprom_cs pin */
#define CCTRL4331_PCIE_MDIO_ON_SPROMCS (1<<6) /* use sprom_cs pin as PCIE mdio interface */
#define CCTRL4331_EXTPA_ON_GPIO2_5 (1<<7) /* aband extpa will be at gpio2/5 and sprom_dout */
#define CCTRL4331_OVR_PIPEAUXCLKEN (1<<8) /* override core control on pipe_AuxClkEnable */
#define CCTRL4331_OVR_PIPEAUXPWRDOWN (1<<9) /* override core control on pipe_AuxPowerDown */
#define CCTRL4331_PCIE_AUXCLKEN (1<<10) /* pcie_auxclkenable */
#define CCTRL4331_PCIE_PIPE_PLLDOWN (1<<11) /* pcie_pipe_pllpowerdown */
#define CCTRL4331_EXTPA_EN2 (1<<12) /* 0 ext pa disable, 1 ext pa enabled */
#define CCTRL4331_EXT_LNA_A (1<<13) /* 0 disable */
#define CCTRL4331_BT_SHD0_ON_GPIO4 (1<<16) /* enable bt_shd0 at gpio4 */
#define CCTRL4331_BT_SHD1_ON_GPIO5 (1<<17) /* enable bt_shd1 at gpio5 */
#define CCTRL4331_EXTPA_ANA_EN (1<<24) /* 0 ext pa disable, 1 ext pa enabled */
/* 4331 Chip specific ChipStatus register bits */
#define CST4331_XTAL_FREQ 0x00000001 /* crystal frequency 20/40Mhz */
#define CST4331_SPROM_OTP_SEL_MASK 0x00000006
#define CST4331_SPROM_OTP_SEL_SHIFT 1
#define CST4331_SPROM_PRESENT 0x00000002
#define CST4331_OTP_PRESENT 0x00000004
#define CST4331_LDO_RF 0x00000008
#define CST4331_LDO_PAR 0x00000010
/* 4315 resource */
#define RES4315_CBUCK_LPOM 1 /* 0x00000002 */
#define RES4315_CBUCK_BURST 2 /* 0x00000004 */
#define RES4315_CBUCK_PWM 3 /* 0x00000008 */
#define RES4315_CLDO_PU 4 /* 0x00000010 */
#define RES4315_PALDO_PU 5 /* 0x00000020 */
#define RES4315_ILP_REQUEST 6 /* 0x00000040 */
#define RES4315_LNLDO1_PU 9 /* 0x00000200 */
#define RES4315_OTP_PU 10 /* 0x00000400 */
#define RES4315_LNLDO2_PU 12 /* 0x00001000 */
#define RES4315_XTAL_PU 13 /* 0x00002000 */
#define RES4315_ALP_AVAIL 14 /* 0x00004000 */
#define RES4315_RX_PWRSW_PU 15 /* 0x00008000 */
#define RES4315_TX_PWRSW_PU 16 /* 0x00010000 */
#define RES4315_RFPLL_PWRSW_PU 17 /* 0x00020000 */
#define RES4315_LOGEN_PWRSW_PU 18 /* 0x00040000 */
#define RES4315_AFE_PWRSW_PU 19 /* 0x00080000 */
#define RES4315_BBPLL_PWRSW_PU 20 /* 0x00100000 */
#define RES4315_HT_AVAIL 21 /* 0x00200000 */
/* 4315 chip-specific ChipStatus register bits */
#define CST4315_SPROM_OTP_SEL_MASK 0x00000003 /* gpio [7:6], SDIO CIS selection */
#define CST4315_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */
#define CST4315_SPROM_SEL 0x00000001 /* use SPROM, OTP is powered up */
#define CST4315_OTP_SEL 0x00000002 /* use OTP, OTP is powered up */
#define CST4315_OTP_PWRDN 0x00000003 /* use SPROM, OTP is powered down */
#define CST4315_SDIO_MODE 0x00000004 /* gpio [8], sdio/usb mode */
#define CST4315_RCAL_VALID 0x00000008
#define CST4315_RCAL_VALUE_MASK 0x000001f0
#define CST4315_RCAL_VALUE_SHIFT 4
#define CST4315_PALDO_EXTPNP 0x00000200 /* PALDO is configured with external PNP */
#define CST4315_CBUCK_MODE_MASK 0x00000c00
#define CST4315_CBUCK_MODE_BURST 0x00000400
#define CST4315_CBUCK_MODE_LPBURST 0x00000c00
/* 4319 resources */
#define RES4319_CBUCK_LPOM 1 /* 0x00000002 */
#define RES4319_CBUCK_BURST 2 /* 0x00000004 */
#define RES4319_CBUCK_PWM 3 /* 0x00000008 */
#define RES4319_CLDO_PU 4 /* 0x00000010 */
#define RES4319_PALDO_PU 5 /* 0x00000020 */
#define RES4319_ILP_REQUEST 6 /* 0x00000040 */
#define RES4319_LNLDO1_PU 9 /* 0x00000200 */
#define RES4319_OTP_PU 10 /* 0x00000400 */
#define RES4319_LNLDO2_PU 12 /* 0x00001000 */
#define RES4319_XTAL_PU 13 /* 0x00002000 */
#define RES4319_ALP_AVAIL 14 /* 0x00004000 */
#define RES4319_RX_PWRSW_PU 15 /* 0x00008000 */
#define RES4319_TX_PWRSW_PU 16 /* 0x00010000 */
#define RES4319_RFPLL_PWRSW_PU 17 /* 0x00020000 */
#define RES4319_LOGEN_PWRSW_PU 18 /* 0x00040000 */
#define RES4319_AFE_PWRSW_PU 19 /* 0x00080000 */
#define RES4319_BBPLL_PWRSW_PU 20 /* 0x00100000 */
#define RES4319_HT_AVAIL 21 /* 0x00200000 */
/* 4319 chip-specific ChipStatus register bits */
#define CST4319_SPI_CPULESSUSB 0x00000001
#define CST4319_SPI_CLK_POL 0x00000002
#define CST4319_SPI_CLK_PH 0x00000008
#define CST4319_SPROM_OTP_SEL_MASK 0x000000c0 /* gpio [7:6], SDIO CIS selection */
#define CST4319_SPROM_OTP_SEL_SHIFT 6
#define CST4319_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */
#define CST4319_SPROM_SEL 0x00000040 /* use SPROM, OTP is powered up */
#define CST4319_OTP_SEL 0x00000080 /* use OTP, OTP is powered up */
#define CST4319_OTP_PWRDN 0x000000c0 /* use SPROM, OTP is powered down */
#define CST4319_SDIO_USB_MODE 0x00000100 /* gpio [8], sdio/usb mode */
#define CST4319_REMAP_SEL_MASK 0x00000600
#define CST4319_ILPDIV_EN 0x00000800
#define CST4319_XTAL_PD_POL 0x00001000
#define CST4319_LPO_SEL 0x00002000
#define CST4319_RES_INIT_MODE 0x0000c000
#define CST4319_PALDO_EXTPNP 0x00010000 /* PALDO is configured with external PNP */
#define CST4319_CBUCK_MODE_MASK 0x00060000
#define CST4319_CBUCK_MODE_BURST 0x00020000
#define CST4319_CBUCK_MODE_LPBURST 0x00060000
#define CST4319_RCAL_VALID 0x01000000
#define CST4319_RCAL_VALUE_MASK 0x3e000000
#define CST4319_RCAL_VALUE_SHIFT 25
#define PMU1_PLL0_CHIPCTL0 0
#define PMU1_PLL0_CHIPCTL1 1
#define PMU1_PLL0_CHIPCTL2 2
#define CCTL_4319USB_XTAL_SEL_MASK 0x00180000
#define CCTL_4319USB_XTAL_SEL_SHIFT 19
#define CCTL_4319USB_48MHZ_PLL_SEL 1
#define CCTL_4319USB_24MHZ_PLL_SEL 2
/* PMU resources for 4336 */
#define RES4336_CBUCK_LPOM 0
#define RES4336_CBUCK_BURST 1
#define RES4336_CBUCK_LP_PWM 2
#define RES4336_CBUCK_PWM 3
#define RES4336_CLDO_PU 4
#define RES4336_DIS_INT_RESET_PD 5
#define RES4336_ILP_REQUEST 6
#define RES4336_LNLDO_PU 7
#define RES4336_LDO3P3_PU 8
#define RES4336_OTP_PU 9
#define RES4336_XTAL_PU 10
#define RES4336_ALP_AVAIL 11
#define RES4336_RADIO_PU 12
#define RES4336_BG_PU 13
#define RES4336_VREG1p4_PU_PU 14
#define RES4336_AFE_PWRSW_PU 15
#define RES4336_RX_PWRSW_PU 16
#define RES4336_TX_PWRSW_PU 17
#define RES4336_BB_PWRSW_PU 18
#define RES4336_SYNTH_PWRSW_PU 19
#define RES4336_MISC_PWRSW_PU 20
#define RES4336_LOGEN_PWRSW_PU 21
#define RES4336_BBPLL_PWRSW_PU 22
#define RES4336_MACPHY_CLKAVAIL 23
#define RES4336_HT_AVAIL 24
#define RES4336_RSVD 25
/* 4336 chip-specific ChipStatus register bits */
#define CST4336_SPI_MODE_MASK 0x00000001
#define CST4336_SPROM_PRESENT 0x00000002
#define CST4336_OTP_PRESENT 0x00000004
#define CST4336_ARMREMAP_0 0x00000008
#define CST4336_ILPDIV_EN_MASK 0x00000010
#define CST4336_ILPDIV_EN_SHIFT 4
#define CST4336_XTAL_PD_POL_MASK 0x00000020
#define CST4336_XTAL_PD_POL_SHIFT 5
#define CST4336_LPO_SEL_MASK 0x00000040
#define CST4336_LPO_SEL_SHIFT 6
#define CST4336_RES_INIT_MODE_MASK 0x00000180
#define CST4336_RES_INIT_MODE_SHIFT 7
#define CST4336_CBUCK_MODE_MASK 0x00000600
#define CST4336_CBUCK_MODE_SHIFT 9
/* 4336 Chip specific PMU ChipControl register bits */
#define PCTL_4336_SERIAL_ENAB (1 << 24)
/* 4330 resources */
#define RES4330_CBUCK_LPOM 0
#define RES4330_CBUCK_BURST 1
#define RES4330_CBUCK_LP_PWM 2
#define RES4330_CBUCK_PWM 3
#define RES4330_CLDO_PU 4
#define RES4330_DIS_INT_RESET_PD 5
#define RES4330_ILP_REQUEST 6
#define RES4330_LNLDO_PU 7
#define RES4330_LDO3P3_PU 8
#define RES4330_OTP_PU 9
#define RES4330_XTAL_PU 10
#define RES4330_ALP_AVAIL 11
#define RES4330_RADIO_PU 12
#define RES4330_BG_PU 13
#define RES4330_VREG1p4_PU_PU 14
#define RES4330_AFE_PWRSW_PU 15
#define RES4330_RX_PWRSW_PU 16
#define RES4330_TX_PWRSW_PU 17
#define RES4330_BB_PWRSW_PU 18
#define RES4330_SYNTH_PWRSW_PU 19
#define RES4330_MISC_PWRSW_PU 20
#define RES4330_LOGEN_PWRSW_PU 21
#define RES4330_BBPLL_PWRSW_PU 22
#define RES4330_MACPHY_CLKAVAIL 23
#define RES4330_HT_AVAIL 24
#define RES4330_5gRX_PWRSW_PU 25
#define RES4330_5gTX_PWRSW_PU 26
#define RES4330_5g_LOGEN_PWRSW_PU 27
/* 4330 chip-specific ChipStatus register bits */
#define CST4330_CHIPMODE_SDIOD(cs) (((cs) & 0x7) < 6) /* SDIO || gSPI */
#define CST4330_CHIPMODE_USB20D(cs) (((cs) & 0x7) >= 6) /* USB || USBDA */
#define CST4330_CHIPMODE_SDIO(cs) (((cs) & 0x4) == 0) /* SDIO */
#define CST4330_CHIPMODE_GSPI(cs) (((cs) & 0x6) == 4) /* gSPI */
#define CST4330_CHIPMODE_USB(cs) (((cs) & 0x7) == 6) /* USB packet-oriented */
#define CST4330_CHIPMODE_USBDA(cs) (((cs) & 0x7) == 7) /* USB Direct Access */
#define CST4330_OTP_PRESENT 0x00000010
#define CST4330_LPO_AUTODET_EN 0x00000020
#define CST4330_ARMREMAP_0 0x00000040
#define CST4330_SPROM_PRESENT 0x00000080 /* takes priority over OTP if both set */
#define CST4330_ILPDIV_EN 0x00000100
#define CST4330_LPO_SEL 0x00000200
#define CST4330_RES_INIT_MODE_SHIFT 10
#define CST4330_RES_INIT_MODE_MASK 0x00000c00
#define CST4330_CBUCK_MODE_SHIFT 12
#define CST4330_CBUCK_MODE_MASK 0x00003000
#define CST4330_CBUCK_POWER_OK 0x00004000
#define CST4330_BB_PLL_LOCKED 0x00008000
#define SOCDEVRAM_BP_ADDR 0x1E000000
#define SOCDEVRAM_ARM_ADDR 0x00800000
/* 4330 Chip specific PMU ChipControl register bits */
#define PCTL_4330_SERIAL_ENAB (1 << 24)
/* 4330 Chip specific ChipControl register bits */
#define CCTRL_4330_GPIO_SEL 0x00000001 /* 1=select GPIOs to be muxed out */
#define CCTRL_4330_ERCX_SEL 0x00000002 /* 1=select ERCX BT coex to be muxed out */
#define CCTRL_4330_SDIO_HOST_WAKE 0x00000004 /* SDIO: 1=configure GPIO0 for host wake */
#define CCTRL_4330_JTAG_DISABLE 0x00000008 /* 1=disable JTAG interface on mux'd pins */
#define PMU_VREG0_ADDR 0
#define PMU_VREG0_DISABLE_PULLD_BT_SHIFT 2
#define PMU_VREG0_DISABLE_PULLD_WL_SHIFT 3
#define PMU_VREG4_ADDR 4
#define PMU_VREG4_CLDO_PWM_SHIFT 4
#define PMU_VREG4_CLDO_PWM_MASK 0x7
#define PMU_VREG4_LPLDO1_SHIFT 15
#define PMU_VREG4_LPLDO1_MASK 0x7
#define PMU_VREG4_LPLDO1_1p20V 0
#define PMU_VREG4_LPLDO1_1p15V 1
#define PMU_VREG4_LPLDO1_1p10V 2
#define PMU_VREG4_LPLDO1_1p25V 3
#define PMU_VREG4_LPLDO1_1p05V 4
#define PMU_VREG4_LPLDO1_1p00V 5
#define PMU_VREG4_LPLDO1_0p95V 6
#define PMU_VREG4_LPLDO1_0p90V 7
/* 4350/4345 VREG4 settings */
#define PMU4350_VREG4_LPLDO1_1p10V 0
#define PMU4350_VREG4_LPLDO1_1p15V 1
#define PMU4350_VREG4_LPLDO1_1p21V 2
#define PMU4350_VREG4_LPLDO1_1p24V 3
#define PMU4350_VREG4_LPLDO1_0p90V 4
#define PMU4350_VREG4_LPLDO1_0p96V 5
#define PMU4350_VREG4_LPLDO1_1p01V 6
#define PMU4350_VREG4_LPLDO1_1p04V 7
#define PMU_VREG4_LPLDO2_LVM_SHIFT 18
#define PMU_VREG4_LPLDO2_LVM_MASK 0x7
#define PMU_VREG4_LPLDO2_HVM_SHIFT 21
#define PMU_VREG4_LPLDO2_HVM_MASK 0x7
#define PMU_VREG4_LPLDO2_LVM_HVM_MASK 0x3f
#define PMU_VREG4_LPLDO2_1p00V 0
#define PMU_VREG4_LPLDO2_1p15V 1
#define PMU_VREG4_LPLDO2_1p20V 2
#define PMU_VREG4_LPLDO2_1p10V 3
#define PMU_VREG4_LPLDO2_0p90V 4 /* 4 - 7 is 0.90V */
#define PMU_VREG4_HSICLDO_BYPASS_SHIFT 27
#define PMU_VREG4_HSICLDO_BYPASS_MASK 0x1
#define PMU_VREG5_ADDR 5
#define PMU_VREG5_HSICAVDD_PD_SHIFT 6
#define PMU_VREG5_HSICAVDD_PD_MASK 0x1
#define PMU_VREG5_HSICDVDD_PD_SHIFT 11
#define PMU_VREG5_HSICDVDD_PD_MASK 0x1
/* 4334 resources */
#define RES4334_LPLDO_PU 0
#define RES4334_RESET_PULLDN_DIS 1
#define RES4334_PMU_BG_PU 2
#define RES4334_HSIC_LDO_PU 3
#define RES4334_CBUCK_LPOM_PU 4
#define RES4334_CBUCK_PFM_PU 5
#define RES4334_CLDO_PU 6
#define RES4334_LPLDO2_LVM 7
#define RES4334_LNLDO_PU 8
#define RES4334_LDO3P3_PU 9
#define RES4334_OTP_PU 10
#define RES4334_XTAL_PU 11
#define RES4334_WL_PWRSW_PU 12
#define RES4334_LQ_AVAIL 13
#define RES4334_LOGIC_RET 14
#define RES4334_MEM_SLEEP 15
#define RES4334_MACPHY_RET 16
#define RES4334_WL_CORE_READY 17
#define RES4334_ILP_REQ 18
#define RES4334_ALP_AVAIL 19
#define RES4334_MISC_PWRSW_PU 20
#define RES4334_SYNTH_PWRSW_PU 21
#define RES4334_RX_PWRSW_PU 22
#define RES4334_RADIO_PU 23
#define RES4334_WL_PMU_PU 24
#define RES4334_VCO_LDO_PU 25
#define RES4334_AFE_LDO_PU 26
#define RES4334_RX_LDO_PU 27
#define RES4334_TX_LDO_PU 28
#define RES4334_HT_AVAIL 29
#define RES4334_MACPHY_CLK_AVAIL 30
/* 4334 chip-specific ChipStatus register bits */
#define CST4334_CHIPMODE_MASK 7
#define CST4334_SDIO_MODE 0x00000000
#define CST4334_SPI_MODE 0x00000004
#define CST4334_HSIC_MODE 0x00000006
#define CST4334_BLUSB_MODE 0x00000007
#define CST4334_CHIPMODE_HSIC(cs) (((cs) & CST4334_CHIPMODE_MASK) == CST4334_HSIC_MODE)
#define CST4334_OTP_PRESENT 0x00000010
#define CST4334_LPO_AUTODET_EN 0x00000020
#define CST4334_ARMREMAP_0 0x00000040
#define CST4334_SPROM_PRESENT 0x00000080
#define CST4334_ILPDIV_EN_MASK 0x00000100
#define CST4334_ILPDIV_EN_SHIFT 8
#define CST4334_LPO_SEL_MASK 0x00000200
#define CST4334_LPO_SEL_SHIFT 9
#define CST4334_RES_INIT_MODE_MASK 0x00000C00
#define CST4334_RES_INIT_MODE_SHIFT 10
/* 4334 Chip specific PMU ChipControl register bits */
#define PCTL_4334_GPIO3_ENAB (1 << 3)
/* 4334 Chip control */
#define CCTRL4334_PMU_WAKEUP_GPIO1 (1 << 0)
#define CCTRL4334_PMU_WAKEUP_HSIC (1 << 1)
#define CCTRL4334_PMU_WAKEUP_AOS (1 << 2)
#define CCTRL4334_HSIC_WAKE_MODE (1 << 3)
#define CCTRL4334_HSIC_INBAND_GPIO1 (1 << 4)
#define CCTRL4334_HSIC_LDO_PU (1 << 23)
/* 4334 Chip control 3 */
#define CCTRL4334_BLOCK_EXTRNL_WAKE (1 << 4)
#define CCTRL4334_SAVERESTORE_FIX (1 << 5)
/* 43341 Chip control 3 */
#define CCTRL43341_BLOCK_EXTRNL_WAKE (1 << 13)
#define CCTRL43341_SAVERESTORE_FIX (1 << 14)
#define CCTRL43341_BT_ISO_SEL (1 << 16)
/* 4334 Chip specific ChipControl1 register bits */
#define CCTRL1_4334_GPIO_SEL (1 << 0) /* 1=select GPIOs to be muxed out */
#define CCTRL1_4334_ERCX_SEL (1 << 1) /* 1=select ERCX BT coex to be muxed out */
#define CCTRL1_4334_SDIO_HOST_WAKE (1 << 2) /* SDIO: 1=configure GPIO0 for host wake */
#define CCTRL1_4334_JTAG_DISABLE (1 << 3) /* 1=disable JTAG interface on mux'd pins */
#define CCTRL1_4334_UART_ON_4_5 (1 << 28) /* 1=UART_TX/UART_RX muxed on GPIO_4/5 (4334B0/1) */
/* 4324 Chip specific ChipControl1 register bits */
#define CCTRL1_4324_GPIO_SEL (1 << 0) /* 1=select GPIOs to be muxed out */
#define CCTRL1_4324_SDIO_HOST_WAKE (1 << 2) /* SDIO: 1=configure GPIO0 for host wake */
/* 43143 chip-specific ChipStatus register bits based on Confluence documentation */
/* register contains strap values sampled during POR */
#define CST43143_REMAP_TO_ROM (3 << 0) /* 00=Boot SRAM, 01=Boot ROM, 10=Boot SFLASH */
#define CST43143_SDIO_EN (1 << 2) /* 0 = USB Enab, SDIO pins are GPIO or I2S */
#define CST43143_SDIO_ISO (1 << 3) /* 1 = SDIO isolated */
#define CST43143_USB_CPU_LESS (1 << 4) /* 1 = CPULess mode Enabled */
#define CST43143_CBUCK_MODE (3 << 6) /* Indicates what controller mode CBUCK is in */
#define CST43143_POK_CBUCK (1 << 8) /* 1 = 1.2V CBUCK voltage ready */
#define CST43143_PMU_OVRSPIKE (1 << 9)
#define CST43143_PMU_OVRTEMP (0xF << 10)
#define CST43143_SR_FLL_CAL_DONE (1 << 14)
#define CST43143_USB_PLL_LOCKDET (1 << 15)
#define CST43143_PMU_PLL_LOCKDET (1 << 16)
#define CST43143_CHIPMODE_SDIOD(cs) (((cs) & CST43143_SDIO_EN) != 0) /* SDIO */
/* 43143 Chip specific ChipControl register bits */
/* 00: SECI is disabled (JATG functional), 01: 2 wire, 10: 4 wire */
#define CCTRL_43143_SECI (1<<0)
#define CCTRL_43143_BT_LEGACY (1<<1)
#define CCTRL_43143_I2S_MODE (1<<2) /* 0: SDIO enabled */
#define CCTRL_43143_I2S_MASTER (1<<3) /* 0: I2S MCLK input disabled */
#define CCTRL_43143_I2S_FULL (1<<4) /* 0: I2S SDIN and SPDIF_TX inputs disabled */
#define CCTRL_43143_GSIO (1<<5) /* 0: sFlash enabled */
#define CCTRL_43143_RF_SWCTRL_MASK (7<<6) /* 0: disabled */
#define CCTRL_43143_RF_SWCTRL_0 (1<<6)
#define CCTRL_43143_RF_SWCTRL_1 (2<<6)
#define CCTRL_43143_RF_SWCTRL_2 (4<<6)
#define CCTRL_43143_RF_XSWCTRL (1<<9) /* 0: UART enabled */
#define CCTRL_43143_HOST_WAKE0 (1<<11) /* 1: SDIO separate interrupt output from GPIO4 */
#define CCTRL_43143_HOST_WAKE1 (1<<12) /* 1: SDIO separate interrupt output from GPIO16 */
/* 43143 resources, based on pmu_params.xls V1.19 */
#define RES43143_EXT_SWITCHER_PWM 0 /* 0x00001 */
#define RES43143_XTAL_PU 1 /* 0x00002 */
#define RES43143_ILP_REQUEST 2 /* 0x00004 */
#define RES43143_ALP_AVAIL 3 /* 0x00008 */
#define RES43143_WL_CORE_READY 4 /* 0x00010 */
#define RES43143_BBPLL_PWRSW_PU 5 /* 0x00020 */
#define RES43143_HT_AVAIL 6 /* 0x00040 */
#define RES43143_RADIO_PU 7 /* 0x00080 */
#define RES43143_MACPHY_CLK_AVAIL 8 /* 0x00100 */
#define RES43143_OTP_PU 9 /* 0x00200 */
#define RES43143_LQ_AVAIL 10 /* 0x00400 */
#define PMU43143_XTAL_CORE_SIZE_MASK 0x3F
/* 4313 resources */
#define RES4313_BB_PU_RSRC 0
#define RES4313_ILP_REQ_RSRC 1
#define RES4313_XTAL_PU_RSRC 2
#define RES4313_ALP_AVAIL_RSRC 3
#define RES4313_RADIO_PU_RSRC 4
#define RES4313_BG_PU_RSRC 5
#define RES4313_VREG1P4_PU_RSRC 6
#define RES4313_AFE_PWRSW_RSRC 7
#define RES4313_RX_PWRSW_RSRC 8
#define RES4313_TX_PWRSW_RSRC 9
#define RES4313_BB_PWRSW_RSRC 10
#define RES4313_SYNTH_PWRSW_RSRC 11
#define RES4313_MISC_PWRSW_RSRC 12
#define RES4313_BB_PLL_PWRSW_RSRC 13
#define RES4313_HT_AVAIL_RSRC 14
#define RES4313_MACPHY_CLK_AVAIL_RSRC 15
/* 4313 chip-specific ChipStatus register bits */
#define CST4313_SPROM_PRESENT 1
#define CST4313_OTP_PRESENT 2
#define CST4313_SPROM_OTP_SEL_MASK 0x00000002
#define CST4313_SPROM_OTP_SEL_SHIFT 0
/* 4313 Chip specific ChipControl register bits */
#define CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */
/* PMU respources for 4314 */
#define RES4314_LPLDO_PU 0
#define RES4314_PMU_SLEEP_DIS 1
#define RES4314_PMU_BG_PU 2
#define RES4314_CBUCK_LPOM_PU 3
#define RES4314_CBUCK_PFM_PU 4
#define RES4314_CLDO_PU 5
#define RES4314_LPLDO2_LVM 6
#define RES4314_WL_PMU_PU 7
#define RES4314_LNLDO_PU 8
#define RES4314_LDO3P3_PU 9
#define RES4314_OTP_PU 10
#define RES4314_XTAL_PU 11
#define RES4314_WL_PWRSW_PU 12
#define RES4314_LQ_AVAIL 13
#define RES4314_LOGIC_RET 14
#define RES4314_MEM_SLEEP 15
#define RES4314_MACPHY_RET 16
#define RES4314_WL_CORE_READY 17
#define RES4314_ILP_REQ 18
#define RES4314_ALP_AVAIL 19
#define RES4314_MISC_PWRSW_PU 20
#define RES4314_SYNTH_PWRSW_PU 21
#define RES4314_RX_PWRSW_PU 22
#define RES4314_RADIO_PU 23
#define RES4314_VCO_LDO_PU 24
#define RES4314_AFE_LDO_PU 25
#define RES4314_RX_LDO_PU 26
#define RES4314_TX_LDO_PU 27
#define RES4314_HT_AVAIL 28
#define RES4314_MACPHY_CLK_AVAIL 29
/* 4314 chip-specific ChipStatus register bits */
#define CST4314_OTP_ENABLED 0x00200000
/* 43228 resources */
#define RES43228_NOT_USED 0
#define RES43228_ILP_REQUEST 1
#define RES43228_XTAL_PU 2
#define RES43228_ALP_AVAIL 3
#define RES43228_PLL_EN 4
#define RES43228_HT_PHY_AVAIL 5
/* 43228 chipstatus reg bits */
#define CST43228_ILP_DIV_EN 0x1
#define CST43228_OTP_PRESENT 0x2
#define CST43228_SERDES_REFCLK_PADSEL 0x4
#define CST43228_SDIO_MODE 0x8
#define CST43228_SDIO_OTP_PRESENT 0x10
#define CST43228_SDIO_RESET 0x20
/* 4706 chipstatus reg bits */
#define CST4706_PKG_OPTION (1<<0) /* 0: full-featured package 1: low-cost package */
#define CST4706_SFLASH_PRESENT (1<<1) /* 0: parallel, 1: serial flash is present */
#define CST4706_SFLASH_TYPE (1<<2) /* 0: 8b-p/ST-s flash, 1: 16b-p/Atmal-s flash */
#define CST4706_MIPS_BENDIAN (1<<3) /* 0: little, 1: big endian */
#define CST4706_PCIE1_DISABLE (1<<5) /* PCIE1 enable strap pin */
/* 4706 flashstrconfig reg bits */
#define FLSTRCF4706_MASK 0x000000ff
#define FLSTRCF4706_SF1 0x00000001 /* 2nd serial flash present */
#define FLSTRCF4706_PF1 0x00000002 /* 2nd parallel flash present */
#define FLSTRCF4706_SF1_TYPE 0x00000004 /* 2nd serial flash type : 0 : ST, 1 : Atmel */
#define FLSTRCF4706_NF1 0x00000008 /* 2nd NAND flash present */
#define FLSTRCF4706_1ST_MADDR_SEG_MASK 0x000000f0 /* Valid value mask */
#define FLSTRCF4706_1ST_MADDR_SEG_4MB 0x00000010 /* 4MB */
#define FLSTRCF4706_1ST_MADDR_SEG_8MB 0x00000020 /* 8MB */
#define FLSTRCF4706_1ST_MADDR_SEG_16MB 0x00000030 /* 16MB */
#define FLSTRCF4706_1ST_MADDR_SEG_32MB 0x00000040 /* 32MB */
#define FLSTRCF4706_1ST_MADDR_SEG_64MB 0x00000050 /* 64MB */
#define FLSTRCF4706_1ST_MADDR_SEG_128MB 0x00000060 /* 128MB */
#define FLSTRCF4706_1ST_MADDR_SEG_256MB 0x00000070 /* 256MB */
/* 4360 Chip specific ChipControl register bits */
#define CCTRL4360_I2C_MODE (1 << 0)
#define CCTRL4360_UART_MODE (1 << 1)
#define CCTRL4360_SECI_MODE (1 << 2)
#define CCTRL4360_BTSWCTRL_MODE (1 << 3)
#define CCTRL4360_DISCRETE_FEMCTRL_MODE (1 << 4)
#define CCTRL4360_DIGITAL_PACTRL_MODE (1 << 5)
#define CCTRL4360_BTSWCTRL_AND_DIGPA_PRESENT (1 << 6)
#define CCTRL4360_EXTRA_GPIO_MODE (1 << 7)
#define CCTRL4360_EXTRA_FEMCTRL_MODE (1 << 8)
#define CCTRL4360_BT_LGCY_MODE (1 << 9)
#define CCTRL4360_CORE2FEMCTRL4_ON (1 << 21)
#define CCTRL4360_SECI_ON_GPIO01 (1 << 24)
/* 4360 Chip specific Regulator Control register bits */
#define RCTRL4360_RFLDO_PWR_DOWN (1 << 1)
/* 4360 PMU resources and chip status bits */
#define RES4360_REGULATOR 0
#define RES4360_ILP_AVAIL 1
#define RES4360_ILP_REQ 2
#define RES4360_XTAL_LDO_PU 3
#define RES4360_XTAL_PU 4
#define RES4360_ALP_AVAIL 5
#define RES4360_BBPLLPWRSW_PU 6
#define RES4360_HT_AVAIL 7
#define RES4360_OTP_PU 8
#define CST4360_XTAL_40MZ 0x00000001
#define CST4360_SFLASH 0x00000002
#define CST4360_SPROM_PRESENT 0x00000004
#define CST4360_SFLASH_TYPE 0x00000004
#define CST4360_OTP_ENABLED 0x00000008
#define CST4360_REMAP_ROM 0x00000010
#define CST4360_RSRC_INIT_MODE_MASK 0x00000060
#define CST4360_RSRC_INIT_MODE_SHIFT 5
#define CST4360_ILP_DIVEN 0x00000080
#define CST4360_MODE_USB 0x00000100
#define CST4360_SPROM_SIZE_MASK 0x00000600
#define CST4360_SPROM_SIZE_SHIFT 9
#define CST4360_BBPLL_LOCK 0x00000800
#define CST4360_AVBBPLL_LOCK 0x00001000
#define CST4360_USBBBPLL_LOCK 0x00002000
#define CST4360_RSRC_INIT_MODE(cs) ((cs & CST4360_RSRC_INIT_MODE_MASK) >> \
CST4360_RSRC_INIT_MODE_SHIFT)
#define CCTRL_4360_UART_SEL 0x2
#define CST4360_RSRC_INIT_MODE(cs) ((cs & CST4360_RSRC_INIT_MODE_MASK) >> \
CST4360_RSRC_INIT_MODE_SHIFT)
/* 43602 PMU resources based on pmu_params.xls version v0.95 */
#define RES43602_LPLDO_PU 0
#define RES43602_REGULATOR 1
#define RES43602_PMU_SLEEP 2
#define RES43602_RSVD_3 3
#define RES43602_XTALLDO_PU 4
#define RES43602_SERDES_PU 5
#define RES43602_BBPLL_PWRSW_PU 6
#define RES43602_SR_CLK_START 7
#define RES43602_SR_PHY_PWRSW 8
#define RES43602_SR_SUBCORE_PWRSW 9
#define RES43602_XTAL_PU 10
#define RES43602_PERST_OVR 11
#define RES43602_SR_CLK_STABLE 12
#define RES43602_SR_SAVE_RESTORE 13
#define RES43602_SR_SLEEP 14
#define RES43602_LQ_START 15
#define RES43602_LQ_AVAIL 16
#define RES43602_WL_CORE_RDY 17
#define RES43602_ILP_REQ 18
#define RES43602_ALP_AVAIL 19
#define RES43602_RADIO_PU 20
#define RES43602_RFLDO_PU 21
#define RES43602_HT_START 22
#define RES43602_HT_AVAIL 23
#define RES43602_MACPHY_CLKAVAIL 24
#define RES43602_PARLDO_PU 25
#define RES43602_RSVD_26 26
/* 43602 chip status bits */
#define CST43602_SPROM_PRESENT (1<<1)
#define CST43602_SPROM_SIZE (1<<10) /* 0 = 16K, 1 = 4K */
#define CST43602_BBPLL_LOCK (1<<11)
#define CST43602_RF_LDO_OUT_OK (1<<15) /* RF LDO output OK */
#define PMU43602_CC1_GPIO12_OVRD (1<<28) /* GPIO12 override */
#define PMU43602_CC2_PCIE_CLKREQ_L_WAKE_EN (1<<1) /* creates gated_pcie_wake, pmu_wakeup logic */
#define PMU43602_CC2_PCIE_PERST_L_WAKE_EN (1<<2) /* creates gated_pcie_wake, pmu_wakeup logic */
#define PMU43602_CC2_ENABLE_L2REFCLKPAD_PWRDWN (1<<3)
#define PMU43602_CC2_PMU_WAKE_ALP_AVAIL_EN (1<<5) /* enable pmu_wakeup to request for ALP_AVAIL */
#define PMU43602_CC2_PERST_L_EXTEND_EN (1<<9) /* extend perst_l until rsc PERST_OVR comes up */
#define PMU43602_CC2_FORCE_EXT_LPO (1<<19) /* 1=ext LPO clock is the final LPO clock */
#define PMU43602_CC2_XTAL32_SEL (1<<30) /* 0=ext_clock, 1=xtal */
#define CC_SR1_43602_SR_ASM_ADDR (0x0)
/* PLL CTL register values for open loop, used during S/R operation */
#define PMU43602_PLL_CTL6_VAL 0x68000528
#define PMU43602_PLL_CTL7_VAL 0x6
#define PMU43602_CC3_ARMCR4_DBG_CLK (1 << 29)
/* 4349 related */
#define RES4349_LPLDO_PU 0
#define RES4349_BG_PU 1
#define RES4349_PMU_SLEEP 2
#define RES4349_PALDO3P3_PU 3
#define RES4349_CBUCK_LPOM_PU 4
#define RES4349_CBUCK_PFM_PU 5
#define RES4349_COLD_START_WAIT 6
#define RES4349_RSVD_7 7
#define RES4349_LNLDO_PU 8
#define RES4349_XTALLDO_PU 9
#define RES4349_LDO3P3_PU 10
#define RES4349_OTP_PU 11
#define RES4349_XTAL_PU 12
#define RES4349_SR_CLK_START 13
#define RES4349_LQ_AVAIL 14
#define RES4349_LQ_START 15
#define RES4349_PERST_OVR 16
#define RES4349_WL_CORE_RDY 17
#define RES4349_ILP_REQ 18
#define RES4349_ALP_AVAIL 19
#define RES4349_MINI_PMU 20
#define RES4349_RADIO_PU 21
#define RES4349_SR_CLK_STABLE 22
#define RES4349_SR_SAVE_RESTORE 23
#define RES4349_SR_PHY_PWRSW 24
#define RES4349_SR_VDDM_PWRSW 25
#define RES4349_SR_SUBCORE_PWRSW 26
#define RES4349_SR_SLEEP 27
#define RES4349_HT_START 28
#define RES4349_HT_AVAIL 29
#define RES4349_MACPHY_CLKAVAIL 30
#define CR4_4349_RAM_BASE (0x180000)
#define CC4_4349_SR_ASM_ADDR (0x48)
#define CST4349_CHIPMODE_SDIOD(cs) (((cs) & (1 << 6)) != 0) /* SDIO */
#define CST4349_CHIPMODE_PCIE(cs) (((cs) & (1 << 7)) != 0) /* PCIE */
#define CST4349_SPROM_PRESENT 0x00000010
/* 43430 PMU resources based on pmu_params.xls */
#define RES43430_LPLDO_PU 0
#define RES43430_BG_PU 1
#define RES43430_PMU_SLEEP 2
#define RES43430_RSVD_3 3
#define RES43430_CBUCK_LPOM_PU 4
#define RES43430_CBUCK_PFM_PU 5
#define RES43430_COLD_START_WAIT 6
#define RES43430_RSVD_7 7
#define RES43430_LNLDO_PU 8
#define RES43430_RSVD_9 9
#define RES43430_LDO3P3_PU 10
#define RES43430_OTP_PU 11
#define RES43430_XTAL_PU 12
#define RES43430_SR_CLK_START 13
#define RES43430_LQ_AVAIL 14
#define RES43430_LQ_START 15
#define RES43430_RSVD_16 16
#define RES43430_WL_CORE_RDY 17
#define RES43430_ILP_REQ 18
#define RES43430_ALP_AVAIL 19
#define RES43430_MINI_PMU 20
#define RES43430_RADIO_PU 21
#define RES43430_SR_CLK_STABLE 22
#define RES43430_SR_SAVE_RESTORE 23
#define RES43430_SR_PHY_PWRSW 24
#define RES43430_SR_VDDM_PWRSW 25
#define RES43430_SR_SUBCORE_PWRSW 26
#define RES43430_SR_SLEEP 27
#define RES43430_HT_START 28
#define RES43430_HT_AVAIL 29
#define RES43430_MACPHY_CLK_AVAIL 30
/* 43430 chip status bits */
#define CST43430_SDIO_MODE 0x00000001
#define CST43430_GSPI_MODE 0x00000002
#define CST43430_RSRC_INIT_MODE_0 0x00000080
#define CST43430_RSRC_INIT_MODE_1 0x00000100
#define CST43430_SEL0_SDIO 0x00000200
#define CST43430_SEL1_SDIO 0x00000400
#define CST43430_SEL2_SDIO 0x00000800
#define CST43430_BBPLL_LOCKED 0x00001000
#define CST43430_DBG_INST_DETECT 0x00004000
#define CST43430_CLB2WL_BT_READY 0x00020000
#define CST43430_JTAG_MODE 0x00100000
#define CST43430_HOST_IFACE 0x00400000
#define CST43430_TRIM_EN 0x00800000
#define CST43430_DIN_PACKAGE_OPTION 0x10000000
/* defines to detect active host interface in use */
#define CHIP_HOSTIF_PCIEMODE 0x1
#define CHIP_HOSTIF_USBMODE 0x2
#define CHIP_HOSTIF_SDIOMODE 0x4
#define CHIP_HOSTIF_PCIE(sih) (si_chip_hostif(sih) == CHIP_HOSTIF_PCIEMODE)
#define CHIP_HOSTIF_USB(sih) (si_chip_hostif(sih) == CHIP_HOSTIF_USBMODE)
#define CHIP_HOSTIF_SDIO(sih) (si_chip_hostif(sih) == CHIP_HOSTIF_SDIOMODE)
/* 4335 resources */
#define RES4335_LPLDO_PO 0
#define RES4335_PMU_BG_PU 1
#define RES4335_PMU_SLEEP 2
#define RES4335_RSVD_3 3
#define RES4335_CBUCK_LPOM_PU 4
#define RES4335_CBUCK_PFM_PU 5
#define RES4335_RSVD_6 6
#define RES4335_RSVD_7 7
#define RES4335_LNLDO_PU 8
#define RES4335_XTALLDO_PU 9
#define RES4335_LDO3P3_PU 10
#define RES4335_OTP_PU 11
#define RES4335_XTAL_PU 12
#define RES4335_SR_CLK_START 13
#define RES4335_LQ_AVAIL 14
#define RES4335_LQ_START 15
#define RES4335_RSVD_16 16
#define RES4335_WL_CORE_RDY 17
#define RES4335_ILP_REQ 18
#define RES4335_ALP_AVAIL 19
#define RES4335_MINI_PMU 20
#define RES4335_RADIO_PU 21
#define RES4335_SR_CLK_STABLE 22
#define RES4335_SR_SAVE_RESTORE 23
#define RES4335_SR_PHY_PWRSW 24
#define RES4335_SR_VDDM_PWRSW 25
#define RES4335_SR_SUBCORE_PWRSW 26
#define RES4335_SR_SLEEP 27
#define RES4335_HT_START 28
#define RES4335_HT_AVAIL 29
#define RES4335_MACPHY_CLKAVAIL 30
/* 4335 Chip specific ChipStatus register bits */
#define CST4335_SPROM_MASK 0x00000020
#define CST4335_SFLASH_MASK 0x00000040
#define CST4335_RES_INIT_MODE_SHIFT 7
#define CST4335_RES_INIT_MODE_MASK 0x00000180
#define CST4335_CHIPMODE_MASK 0xF
#define CST4335_CHIPMODE_SDIOD(cs) (((cs) & (1 << 0)) != 0) /* SDIO */
#define CST4335_CHIPMODE_GSPI(cs) (((cs) & (1 << 1)) != 0) /* gSPI */
#define CST4335_CHIPMODE_USB20D(cs) (((cs) & (1 << 2)) != 0) /* HSIC || USBDA */
#define CST4335_CHIPMODE_PCIE(cs) (((cs) & (1 << 3)) != 0) /* PCIE */
/* 4335 Chip specific ChipControl1 register bits */
#define CCTRL1_4335_GPIO_SEL (1 << 0) /* 1=select GPIOs to be muxed out */
#define CCTRL1_4335_SDIO_HOST_WAKE (1 << 2) /* SDIO: 1=configure GPIO0 for host wake */
/* 4335 Chip specific ChipControl2 register bits */
#define CCTRL2_4335_AOSBLOCK (1 << 30)
#define CCTRL2_4335_PMUWAKE (1 << 31)
#define PATCHTBL_SIZE (0x800)
#define CR4_4335_RAM_BASE (0x180000)
#define CR4_4345_RAM_BASE (0x1b0000)
#define CR4_4349_RAM_BASE (0x180000)
#define CR4_4350_RAM_BASE (0x180000)
#define CR4_4360_RAM_BASE (0x0)
#define CR4_43602_RAM_BASE (0x180000)
/* 4335 chip OTP present & OTP select bits. */
#define SPROM4335_OTP_SELECT 0x00000010
#define SPROM4335_OTP_PRESENT 0x00000020
/* 4335 GCI specific bits. */
#define CC4335_GCI_STRAP_OVERRIDE_SFLASH_PRESENT (1 << 24)
#define CC4335_GCI_STRAP_OVERRIDE_SFLASH_TYPE 25
#define CC4335_GCI_FUNC_SEL_PAD_SDIO 0x00707770
/* SFLASH clkdev specific bits. */
#define CC4335_SFLASH_CLKDIV_MASK 0x1F000000
#define CC4335_SFLASH_CLKDIV_SHIFT 25
/* 4335 OTP bits for SFLASH. */
#define CC4335_SROM_OTP_SFLASH 40
#define CC4335_SROM_OTP_SFLASH_PRESENT 0x1
#define CC4335_SROM_OTP_SFLASH_TYPE 0x2
#define CC4335_SROM_OTP_SFLASH_CLKDIV_MASK 0x003C
#define CC4335_SROM_OTP_SFLASH_CLKDIV_SHIFT 2
/* 4335 chip OTP present & OTP select bits. */
#define SPROM4335_OTP_SELECT 0x00000010
#define SPROM4335_OTP_PRESENT 0x00000020
/* 4335 GCI specific bits. */
#define CC4335_GCI_STRAP_OVERRIDE_SFLASH_PRESENT (1 << 24)
#define CC4335_GCI_STRAP_OVERRIDE_SFLASH_TYPE 25
#define CC4335_GCI_FUNC_SEL_PAD_SDIO 0x00707770
/* SFLASH clkdev specific bits. */
#define CC4335_SFLASH_CLKDIV_MASK 0x1F000000
#define CC4335_SFLASH_CLKDIV_SHIFT 25
/* 4335 OTP bits for SFLASH. */
#define CC4335_SROM_OTP_SFLASH 40
#define CC4335_SROM_OTP_SFLASH_PRESENT 0x1
#define CC4335_SROM_OTP_SFLASH_TYPE 0x2
#define CC4335_SROM_OTP_SFLASH_CLKDIV_MASK 0x003C
#define CC4335_SROM_OTP_SFLASH_CLKDIV_SHIFT 2
/* 4335 resources--END */
/* 4345 Chip specific ChipStatus register bits */
#define CST4345_SPROM_MASK 0x00000020
#define CST4345_SFLASH_MASK 0x00000040
#define CST4345_RES_INIT_MODE_SHIFT 7
#define CST4345_RES_INIT_MODE_MASK 0x00000180
#define CST4345_CHIPMODE_MASK 0x4000F
#define CST4345_CHIPMODE_SDIOD(cs) (((cs) & (1 << 0)) != 0) /* SDIO */
#define CST4345_CHIPMODE_GSPI(cs) (((cs) & (1 << 1)) != 0) /* gSPI */
#define CST4345_CHIPMODE_HSIC(cs) (((cs) & (1 << 2)) != 0) /* HSIC */
#define CST4345_CHIPMODE_PCIE(cs) (((cs) & (1 << 3)) != 0) /* PCIE */
#define CST4345_CHIPMODE_USB20D(cs) (((cs) & (1 << 18)) != 0) /* USBDA */
/* 4350 Chipcommon ChipStatus bits */
#define CST4350_SDIO_MODE 0x00000001
#define CST4350_HSIC20D_MODE 0x00000002
#define CST4350_BP_ON_HSIC_CLK 0x00000004
#define CST4350_PCIE_MODE 0x00000008
#define CST4350_USB20D_MODE 0x00000010
#define CST4350_USB30D_MODE 0x00000020
#define CST4350_SPROM_PRESENT 0x00000040
#define CST4350_RSRC_INIT_MODE_0 0x00000080
#define CST4350_RSRC_INIT_MODE_1 0x00000100
#define CST4350_SEL0_SDIO 0x00000200
#define CST4350_SEL1_SDIO 0x00000400
#define CST4350_SDIO_PAD_MODE 0x00000800
#define CST4350_BBPLL_LOCKED 0x00001000
#define CST4350_USBPLL_LOCKED 0x00002000
#define CST4350_LINE_STATE 0x0000C000
#define CST4350_SERDES_PIPE_PLLLOCK 0x00010000
#define CST4350_BT_READY 0x00020000
#define CST4350_SFLASH_PRESENT 0x00040000
#define CST4350_CPULESS_ENABLE 0x00080000
#define CST4350_STRAP_HOST_IFC_1 0x00100000
#define CST4350_STRAP_HOST_IFC_2 0x00200000
#define CST4350_STRAP_HOST_IFC_3 0x00400000
#define CST4350_RAW_SPROM_PRESENT 0x00800000
#define CST4350_APP_CLK_SWITCH_SEL_RDBACK 0x01000000
#define CST4350_RAW_RSRC_INIT_MODE_0 0x02000000
#define CST4350_SDIO_PAD_VDDIO 0x04000000
#define CST4350_GSPI_MODE 0x08000000
#define CST4350_PACKAGE_OPTION 0xF0000000
#define CST4350_PACKAGE_SHIFT 28
/* package option for 4350 */
#define CST4350_PACKAGE_WLCSP 0x0
#define CST4350_PACKAGE_PCIE 0x1
#define CST4350_PACKAGE_WLBGA 0x2
#define CST4350_PACKAGE_DBG 0x3
#define CST4350_PACKAGE_USB 0x4
#define CST4350_PACKAGE_USB_HSIC 0x4
#define CST4350_PKG_MODE(cs) ((cs & CST4350_PACKAGE_OPTION) >> CST4350_PACKAGE_SHIFT)
#define CST4350_PKG_WLCSP(cs) (CST4350_PKG_MODE(cs) == (CST4350_PACKAGE_WLCSP))
#define CST4350_PKG_PCIE(cs) (CST4350_PKG_MODE(cs) == (CST4350_PACKAGE_PCIE))
#define CST4350_PKG_WLBGA(cs) (CST4350_PKG_MODE(cs) == (CST4350_PACKAGE_WLBGA))
#define CST4350_PKG_USB(cs) (CST4350_PKG_MODE(cs) == (CST4350_PACKAGE_USB))
#define CST4350_PKG_USB_HSIC(cs) (CST4350_PKG_MODE(cs) == (CST4350_PACKAGE_USB_HSIC))
/* 4350C0 USB PACKAGE using raw_sprom_present to indicate 40mHz xtal */
#define CST4350_PKG_USB_40M(cs) (cs & CST4350_RAW_SPROM_PRESENT)
#define CST4350_CHIPMODE_SDIOD(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_SDIOD))
#define CST4350_CHIPMODE_USB20D(cs) ((CST4350_IFC_MODE(cs)) == (CST4350_IFC_MODE_USB20D))
#define CST4350_CHIPMODE_HSIC20D(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_HSIC20D))
#define CST4350_CHIPMODE_HSIC30D(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_HSIC30D))
#define CST4350_CHIPMODE_USB30D(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_USB30D))
#define CST4350_CHIPMODE_USB30D_WL(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_USB30D_WL))
#define CST4350_CHIPMODE_PCIE(cs) (CST4350_IFC_MODE(cs) == (CST4350_IFC_MODE_PCIE))
/* strap_host_ifc strap value */
#define CST4350_HOST_IFC_MASK 0x00700000
#define CST4350_HOST_IFC_SHIFT 20
/* host_ifc raw mode */
#define CST4350_IFC_MODE_SDIOD 0x0
#define CST4350_IFC_MODE_HSIC20D 0x1
#define CST4350_IFC_MODE_HSIC30D 0x2
#define CST4350_IFC_MODE_PCIE 0x3
#define CST4350_IFC_MODE_USB20D 0x4
#define CST4350_IFC_MODE_USB30D 0x5
#define CST4350_IFC_MODE_USB30D_WL 0x6
#define CST4350_IFC_MODE_USB30D_BT 0x7
#define CST4350_IFC_MODE(cs) ((cs & CST4350_HOST_IFC_MASK) >> CST4350_HOST_IFC_SHIFT)
/* 4350 PMU resources */
#define RES4350_LPLDO_PU 0
#define RES4350_PMU_BG_PU 1
#define RES4350_PMU_SLEEP 2
#define RES4350_RSVD_3 3
#define RES4350_CBUCK_LPOM_PU 4
#define RES4350_CBUCK_PFM_PU 5
#define RES4350_COLD_START_WAIT 6
#define RES4350_RSVD_7 7
#define RES4350_LNLDO_PU 8
#define RES4350_XTALLDO_PU 9
#define RES4350_LDO3P3_PU 10
#define RES4350_OTP_PU 11
#define RES4350_XTAL_PU 12
#define RES4350_SR_CLK_START 13
#define RES4350_LQ_AVAIL 14
#define RES4350_LQ_START 15
#define RES4350_PERST_OVR 16
#define RES4350_WL_CORE_RDY 17
#define RES4350_ILP_REQ 18
#define RES4350_ALP_AVAIL 19
#define RES4350_MINI_PMU 20
#define RES4350_RADIO_PU 21
#define RES4350_SR_CLK_STABLE 22
#define RES4350_SR_SAVE_RESTORE 23
#define RES4350_SR_PHY_PWRSW 24
#define RES4350_SR_VDDM_PWRSW 25
#define RES4350_SR_SUBCORE_PWRSW 26
#define RES4350_SR_SLEEP 27
#define RES4350_HT_START 28
#define RES4350_HT_AVAIL 29
#define RES4350_MACPHY_CLKAVAIL 30
#define MUXENAB4350_UART_MASK (0x0000000f)
#define MUXENAB4350_UART_SHIFT 0
#define MUXENAB4350_HOSTWAKE_MASK (0x000000f0) /* configure GPIO for SDIO host_wake */
#define MUXENAB4350_HOSTWAKE_SHIFT 4
/* 4350 GCI function sel values */
#define CC4350_FNSEL_HWDEF (0)
#define CC4350_FNSEL_SAMEASPIN (1)
#define CC4350_FNSEL_UART (2)
#define CC4350_FNSEL_SFLASH (3)
#define CC4350_FNSEL_SPROM (4)
#define CC4350_FNSEL_I2C (5)
#define CC4350_FNSEL_MISC0 (6)
#define CC4350_FNSEL_GCI (7)
#define CC4350_FNSEL_MISC1 (8)
#define CC4350_FNSEL_MISC2 (9)
#define CC4350_FNSEL_PWDOG (10)
#define CC4350_FNSEL_IND (12)
#define CC4350_FNSEL_PDN (13)
#define CC4350_FNSEL_PUP (14)
#define CC4350_FNSEL_TRISTATE (15)
#define CC4350C_FNSEL_UART (3)
/* 4350 GPIO */
#define CC4350_PIN_GPIO_00 (0)
#define CC4350_PIN_GPIO_01 (1)
#define CC4350_PIN_GPIO_02 (2)
#define CC4350_PIN_GPIO_03 (3)
#define CC4350_PIN_GPIO_04 (4)
#define CC4350_PIN_GPIO_05 (5)
#define CC4350_PIN_GPIO_06 (6)
#define CC4350_PIN_GPIO_07 (7)
#define CC4350_PIN_GPIO_08 (8)
#define CC4350_PIN_GPIO_09 (9)
#define CC4350_PIN_GPIO_10 (10)
#define CC4350_PIN_GPIO_11 (11)
#define CC4350_PIN_GPIO_12 (12)
#define CC4350_PIN_GPIO_13 (13)
#define CC4350_PIN_GPIO_14 (14)
#define CC4350_PIN_GPIO_15 (15)
#define CC4350_RSVD_16_SHIFT 16
#define CC2_4350_PHY_PWRSW_UPTIME_MASK (0xf << 0)
#define CC2_4350_PHY_PWRSW_UPTIME_SHIFT (0)
#define CC2_4350_VDDM_PWRSW_UPDELAY_MASK (0xf << 4)
#define CC2_4350_VDDM_PWRSW_UPDELAY_SHIFT (4)
#define CC2_4350_VDDM_PWRSW_UPTIME_MASK (0xf << 8)
#define CC2_4350_VDDM_PWRSW_UPTIME_SHIFT (8)
#define CC2_4350_SBC_PWRSW_DNDELAY_MASK (0x3 << 12)
#define CC2_4350_SBC_PWRSW_DNDELAY_SHIFT (12)
#define CC2_4350_PHY_PWRSW_DNDELAY_MASK (0x3 << 14)
#define CC2_4350_PHY_PWRSW_DNDELAY_SHIFT (14)
#define CC2_4350_VDDM_PWRSW_DNDELAY_MASK (0x3 << 16)
#define CC2_4350_VDDM_PWRSW_DNDELAY_SHIFT (16)
#define CC2_4350_VDDM_PWRSW_EN_MASK (1 << 20)
#define CC2_4350_VDDM_PWRSW_EN_SHIFT (20)
#define CC2_4350_MEMLPLDO_PWRSW_EN_MASK (1 << 21)
#define CC2_4350_MEMLPLDO_PWRSW_EN_SHIFT (21)
#define CC2_4350_SDIO_AOS_WAKEUP_MASK (1 << 24)
#define CC2_4350_SDIO_AOS_WAKEUP_SHIFT (24)
/* Applies to 4335/4350/4345 */
#define CC3_SR_CLK_SR_MEM_MASK (1 << 0)
#define CC3_SR_CLK_SR_MEM_SHIFT (0)
#define CC3_SR_BIT1_TBD_MASK (1 << 1)
#define CC3_SR_BIT1_TBD_SHIFT (1)
#define CC3_SR_ENGINE_ENABLE_MASK (1 << 2)
#define CC3_SR_ENGINE_ENABLE_SHIFT (2)
#define CC3_SR_BIT3_TBD_MASK (1 << 3)
#define CC3_SR_BIT3_TBD_SHIFT (3)
#define CC3_SR_MINDIV_FAST_CLK_MASK (0xF << 4)
#define CC3_SR_MINDIV_FAST_CLK_SHIFT (4)
#define CC3_SR_R23_SR2_RISE_EDGE_TRIG_MASK (1 << 8)
#define CC3_SR_R23_SR2_RISE_EDGE_TRIG_SHIFT (8)
#define CC3_SR_R23_SR2_FALL_EDGE_TRIG_MASK (1 << 9)
#define CC3_SR_R23_SR2_FALL_EDGE_TRIG_SHIFT (9)
#define CC3_SR_R23_SR_RISE_EDGE_TRIG_MASK (1 << 10)
#define CC3_SR_R23_SR_RISE_EDGE_TRIG_SHIFT (10)
#define CC3_SR_R23_SR_FALL_EDGE_TRIG_MASK (1 << 11)
#define CC3_SR_R23_SR_FALL_EDGE_TRIG_SHIFT (11)
#define CC3_SR_NUM_CLK_HIGH_MASK (0x7 << 12)
#define CC3_SR_NUM_CLK_HIGH_SHIFT (12)
#define CC3_SR_BIT15_TBD_MASK (1 << 15)
#define CC3_SR_BIT15_TBD_SHIFT (15)
#define CC3_SR_PHY_FUNC_PIC_MASK (1 << 16)
#define CC3_SR_PHY_FUNC_PIC_SHIFT (16)
#define CC3_SR_BIT17_19_TBD_MASK (0x7 << 17)
#define CC3_SR_BIT17_19_TBD_SHIFT (17)
#define CC3_SR_CHIP_TRIGGER_1_MASK (1 << 20)
#define CC3_SR_CHIP_TRIGGER_1_SHIFT (20)
#define CC3_SR_CHIP_TRIGGER_2_MASK (1 << 21)
#define CC3_SR_CHIP_TRIGGER_2_SHIFT (21)
#define CC3_SR_CHIP_TRIGGER_3_MASK (1 << 22)
#define CC3_SR_CHIP_TRIGGER_3_SHIFT (22)
#define CC3_SR_CHIP_TRIGGER_4_MASK (1 << 23)
#define CC3_SR_CHIP_TRIGGER_4_SHIFT (23)
#define CC3_SR_ALLOW_SBC_FUNC_PIC_MASK (1 << 24)
#define CC3_SR_ALLOW_SBC_FUNC_PIC_SHIFT (24)
#define CC3_SR_BIT25_26_TBD_MASK (0x3 << 25)
#define CC3_SR_BIT25_26_TBD_SHIFT (25)
#define CC3_SR_ALLOW_SBC_STBY_MASK (1 << 27)
#define CC3_SR_ALLOW_SBC_STBY_SHIFT (27)
#define CC3_SR_GPIO_MUX_MASK (0xF << 28)
#define CC3_SR_GPIO_MUX_SHIFT (28)
/* Applies to 4335/4350/4345 */
#define CC4_SR_INIT_ADDR_MASK (0x3FF0000)
#define CC4_4350_SR_ASM_ADDR (0x30)
#define CC4_4350_C0_SR_ASM_ADDR (0x0)
#define CC4_4335_SR_ASM_ADDR (0x48)
#define CC4_4345_SR_ASM_ADDR (0x48)
#define CC4_SR_INIT_ADDR_SHIFT (16)
#define CC4_4350_EN_SR_CLK_ALP_MASK (1 << 30)
#define CC4_4350_EN_SR_CLK_ALP_SHIFT (30)
#define CC4_4350_EN_SR_CLK_HT_MASK (1 << 31)
#define CC4_4350_EN_SR_CLK_HT_SHIFT (31)
#define VREG4_4350_MEMLPDO_PU_MASK (1 << 31)
#define VREG4_4350_MEMLPDO_PU_SHIFT 31
#define VREG6_4350_SR_EXT_CLKDIR_MASK (1 << 20)
#define VREG6_4350_SR_EXT_CLKDIR_SHIFT 20
#define VREG6_4350_SR_EXT_CLKDIV_MASK (0x3 << 21)
#define VREG6_4350_SR_EXT_CLKDIV_SHIFT 21
#define VREG6_4350_SR_EXT_CLKEN_MASK (1 << 23)
#define VREG6_4350_SR_EXT_CLKEN_SHIFT 23
#define CC5_4350_PMU_EN_ASSERT_MASK (1 << 13)
#define CC5_4350_PMU_EN_ASSERT_SHIFT (13)
#define CC6_4350_PCIE_CLKREQ_WAKEUP_MASK (1 << 4)
#define CC6_4350_PCIE_CLKREQ_WAKEUP_SHIFT (4)
#define CC6_4350_PMU_WAKEUP_ALPAVAIL_MASK (1 << 6)
#define CC6_4350_PMU_WAKEUP_ALPAVAIL_SHIFT (6)
#define CC6_4350_PMU_EN_EXT_PERST_MASK (1 << 17)
#define CC6_4350_PMU_EN_EXT_PERST_SHIFT (17)
#define CC6_4350_PMU_EN_WAKEUP_MASK (1 << 18)
#define CC6_4350_PMU_EN_WAKEUP_SHIFT (18)
#define CC7_4350_PMU_EN_ASSERT_L2_MASK (1 << 26)
#define CC7_4350_PMU_EN_ASSERT_L2_SHIFT (26)
#define CC7_4350_PMU_EN_MDIO_MASK (1 << 27)
#define CC7_4350_PMU_EN_MDIO_SHIFT (27)
#define CC6_4345_PMU_EN_PERST_DEASSERT_MASK (1 << 13)
#define CC6_4345_PMU_EN_PERST_DEASSERT_SHIF (13)
#define CC6_4345_PMU_EN_L2_DEASSERT_MASK (1 << 14)
#define CC6_4345_PMU_EN_L2_DEASSERT_SHIF (14)
#define CC6_4345_PMU_EN_ASSERT_L2_MASK (1 << 15)
#define CC6_4345_PMU_EN_ASSERT_L2_SHIFT (15)
#define CC6_4345_PMU_EN_MDIO_MASK (1 << 24)
#define CC6_4345_PMU_EN_MDIO_SHIFT (24)
/* GCI chipcontrol register indices */
#define CC_GCI_CHIPCTRL_00 (0)
#define CC_GCI_CHIPCTRL_01 (1)
#define CC_GCI_CHIPCTRL_02 (2)
#define CC_GCI_CHIPCTRL_03 (3)
#define CC_GCI_CHIPCTRL_04 (4)
#define CC_GCI_CHIPCTRL_05 (5)
#define CC_GCI_CHIPCTRL_06 (6)
#define CC_GCI_CHIPCTRL_07 (7)
#define CC_GCI_CHIPCTRL_08 (8)
#define CC_GCI_XTAL_BUFSTRG_NFC (0xff << 12)
#define CC_GCI_06_JTAG_SEL_SHIFT 4
#define CC_GCI_06_JTAG_SEL_MASK (1 << 4)
#define CC_GCI_NUMCHIPCTRLREGS(cap1) ((cap1 & 0xF00) >> 8)
/* 4345 PMU resources */
#define RES4345_LPLDO_PU 0
#define RES4345_PMU_BG_PU 1
#define RES4345_PMU_SLEEP 2
#define RES4345_HSICLDO_PU 3
#define RES4345_CBUCK_LPOM_PU 4
#define RES4345_CBUCK_PFM_PU 5
#define RES4345_COLD_START_WAIT 6
#define RES4345_RSVD_7 7
#define RES4345_LNLDO_PU 8
#define RES4345_XTALLDO_PU 9
#define RES4345_LDO3P3_PU 10
#define RES4345_OTP_PU 11
#define RES4345_XTAL_PU 12
#define RES4345_SR_CLK_START 13
#define RES4345_LQ_AVAIL 14
#define RES4345_LQ_START 15
#define RES4345_PERST_OVR 16
#define RES4345_WL_CORE_RDY 17
#define RES4345_ILP_REQ 18
#define RES4345_ALP_AVAIL 19
#define RES4345_MINI_PMU 20
#define RES4345_RADIO_PU 21
#define RES4345_SR_CLK_STABLE 22
#define RES4345_SR_SAVE_RESTORE 23
#define RES4345_SR_PHY_PWRSW 24
#define RES4345_SR_VDDM_PWRSW 25
#define RES4345_SR_SUBCORE_PWRSW 26
#define RES4345_SR_SLEEP 27
#define RES4345_HT_START 28
#define RES4345_HT_AVAIL 29
#define RES4345_MACPHY_CLK_AVAIL 30
/* 4335 pins
* note: only the values set as default/used are added here.
*/
#define CC4335_PIN_GPIO_00 (0)
#define CC4335_PIN_GPIO_01 (1)
#define CC4335_PIN_GPIO_02 (2)
#define CC4335_PIN_GPIO_03 (3)
#define CC4335_PIN_GPIO_04 (4)
#define CC4335_PIN_GPIO_05 (5)
#define CC4335_PIN_GPIO_06 (6)
#define CC4335_PIN_GPIO_07 (7)
#define CC4335_PIN_GPIO_08 (8)
#define CC4335_PIN_GPIO_09 (9)
#define CC4335_PIN_GPIO_10 (10)
#define CC4335_PIN_GPIO_11 (11)
#define CC4335_PIN_GPIO_12 (12)
#define CC4335_PIN_GPIO_13 (13)
#define CC4335_PIN_GPIO_14 (14)
#define CC4335_PIN_GPIO_15 (15)
#define CC4335_PIN_SDIO_CLK (16)
#define CC4335_PIN_SDIO_CMD (17)
#define CC4335_PIN_SDIO_DATA0 (18)
#define CC4335_PIN_SDIO_DATA1 (19)
#define CC4335_PIN_SDIO_DATA2 (20)
#define CC4335_PIN_SDIO_DATA3 (21)
#define CC4335_PIN_RF_SW_CTRL_6 (22)
#define CC4335_PIN_RF_SW_CTRL_7 (23)
#define CC4335_PIN_RF_SW_CTRL_8 (24)
#define CC4335_PIN_RF_SW_CTRL_9 (25)
/* Last GPIO Pad */
#define CC4335_PIN_GPIO_LAST (31)
/* 4335 GCI function sel values
*/
#define CC4335_FNSEL_HWDEF (0)
#define CC4335_FNSEL_SAMEASPIN (1)
#define CC4335_FNSEL_GPIO0 (2)
#define CC4335_FNSEL_GPIO1 (3)
#define CC4335_FNSEL_GCI0 (4)
#define CC4335_FNSEL_GCI1 (5)
#define CC4335_FNSEL_UART (6)
#define CC4335_FNSEL_SFLASH (7)
#define CC4335_FNSEL_SPROM (8)
#define CC4335_FNSEL_MISC0 (9)
#define CC4335_FNSEL_MISC1 (10)
#define CC4335_FNSEL_MISC2 (11)
#define CC4335_FNSEL_IND (12)
#define CC4335_FNSEL_PDN (13)
#define CC4335_FNSEL_PUP (14)
#define CC4335_FNSEL_TRI (15)
/* GCI Core Control Reg */
#define GCI_CORECTRL_SR_MASK (1 << 0) /* SECI block Reset */
#define GCI_CORECTRL_RSL_MASK (1 << 1) /* ResetSECILogic */
#define GCI_CORECTRL_ES_MASK (1 << 2) /* EnableSECI */
#define GCI_CORECTRL_FSL_MASK (1 << 3) /* Force SECI Out Low */
#define GCI_CORECTRL_SOM_MASK (7 << 4) /* SECI Op Mode */
#define GCI_CORECTRL_US_MASK (1 << 7) /* Update SECI */
#define GCI_CORECTRL_BOS_MASK (1 << 8) /* Break On Sleep */
/* 4345 pins
* note: only the values set as default/used are added here.
*/
#define CC4345_PIN_GPIO_00 (0)
#define CC4345_PIN_GPIO_01 (1)
#define CC4345_PIN_GPIO_02 (2)
#define CC4345_PIN_GPIO_03 (3)
#define CC4345_PIN_GPIO_04 (4)
#define CC4345_PIN_GPIO_05 (5)
#define CC4345_PIN_GPIO_06 (6)
#define CC4345_PIN_GPIO_07 (7)
#define CC4345_PIN_GPIO_08 (8)
#define CC4345_PIN_GPIO_09 (9)
#define CC4345_PIN_GPIO_10 (10)
#define CC4345_PIN_GPIO_11 (11)
#define CC4345_PIN_GPIO_12 (12)
#define CC4345_PIN_GPIO_13 (13)
#define CC4345_PIN_GPIO_14 (14)
#define CC4345_PIN_GPIO_15 (15)
#define CC4345_PIN_GPIO_16 (16)
#define CC4345_PIN_SDIO_CLK (17)
#define CC4345_PIN_SDIO_CMD (18)
#define CC4345_PIN_SDIO_DATA0 (19)
#define CC4345_PIN_SDIO_DATA1 (20)
#define CC4345_PIN_SDIO_DATA2 (21)
#define CC4345_PIN_SDIO_DATA3 (22)
#define CC4345_PIN_RF_SW_CTRL_0 (23)
#define CC4345_PIN_RF_SW_CTRL_1 (24)
#define CC4345_PIN_RF_SW_CTRL_2 (25)
#define CC4345_PIN_RF_SW_CTRL_3 (26)
#define CC4345_PIN_RF_SW_CTRL_4 (27)
#define CC4345_PIN_RF_SW_CTRL_5 (28)
#define CC4345_PIN_RF_SW_CTRL_6 (29)
#define CC4345_PIN_RF_SW_CTRL_7 (30)
#define CC4345_PIN_RF_SW_CTRL_8 (31)
#define CC4345_PIN_RF_SW_CTRL_9 (32)
/* 4345 GCI function sel values
*/
#define CC4345_FNSEL_HWDEF (0)
#define CC4345_FNSEL_SAMEASPIN (1)
#define CC4345_FNSEL_GPIO0 (2)
#define CC4345_FNSEL_GPIO1 (3)
#define CC4345_FNSEL_GCI0 (4)
#define CC4345_FNSEL_GCI1 (5)
#define CC4345_FNSEL_UART (6)
#define CC4345_FNSEL_SFLASH (7)
#define CC4345_FNSEL_SPROM (8)
#define CC4345_FNSEL_MISC0 (9)
#define CC4345_FNSEL_MISC1 (10)
#define CC4345_FNSEL_MISC2 (11)
#define CC4345_FNSEL_IND (12)
#define CC4345_FNSEL_PDN (13)
#define CC4345_FNSEL_PUP (14)
#define CC4345_FNSEL_TRI (15)
#define MUXENAB4345_UART_MASK (0x0000000f)
#define MUXENAB4345_UART_SHIFT 0
#define MUXENAB4345_HOSTWAKE_MASK (0x000000f0)
#define MUXENAB4345_HOSTWAKE_SHIFT 4
/* 4349 Group (4349, 4355, 4359) GCI AVS function sel values */
#define CC4349_GRP_GCI_AVS_CTRL_MASK (0xffe00000)
#define CC4349_GRP_GCI_AVS_CTRL_SHIFT (21)
#define CC4349_GRP_GCI_AVS_CTRL_ENAB (1 << 5)
/* 4345 GCI AVS function sel values */
#define CC4345_GCI_AVS_CTRL_MASK (0xfc)
#define CC4345_GCI_AVS_CTRL_SHIFT (2)
#define CC4345_GCI_AVS_CTRL_ENAB (1 << 5)
/* GCI GPIO for function sel GCI-0/GCI-1 */
#define CC_GCI_GPIO_0 (0)
#define CC_GCI_GPIO_1 (1)
#define CC_GCI_GPIO_2 (2)
#define CC_GCI_GPIO_3 (3)
#define CC_GCI_GPIO_4 (4)
#define CC_GCI_GPIO_5 (5)
#define CC_GCI_GPIO_6 (6)
#define CC_GCI_GPIO_7 (7)
#define CC_GCI_GPIO_8 (8)
#define CC_GCI_GPIO_9 (9)
#define CC_GCI_GPIO_10 (10)
#define CC_GCI_GPIO_11 (11)
#define CC_GCI_GPIO_12 (12)
#define CC_GCI_GPIO_13 (13)
#define CC_GCI_GPIO_14 (14)
#define CC_GCI_GPIO_15 (15)
/* indicates Invalid GPIO, e.g. when PAD GPIO doesn't map to GCI GPIO */
#define CC_GCI_GPIO_INVALID 0xFF
/* find the 4 bit mask given the bit position */
#define GCIMASK(pos) (((uint32)0xF) << pos)
/* get the value which can be used to directly OR with chipcontrol reg */
#define GCIPOSVAL(val, pos) ((((uint32)val) << pos) & GCIMASK(pos))
/* Extract nibble from a given position */
#define GCIGETNBL(val, pos) ((val >> pos) & 0xF)
/* find the 8 bit mask given the bit position */
#define GCIMASK_8B(pos) (((uint32)0xFF) << pos)
/* get the value which can be used to directly OR with chipcontrol reg */
#define GCIPOSVAL_8B(val, pos) ((((uint32)val) << pos) & GCIMASK_8B(pos))
/* Extract nibble from a given position */
#define GCIGETNBL_8B(val, pos) ((val >> pos) & 0xFF)
/* find the 4 bit mask given the bit position */
#define GCIMASK_4B(pos) (((uint32)0xF) << pos)
/* get the value which can be used to directly OR with chipcontrol reg */
#define GCIPOSVAL_4B(val, pos) ((((uint32)val) << pos) & GCIMASK_4B(pos))
/* Extract nibble from a given position */
#define GCIGETNBL_4B(val, pos) ((val >> pos) & 0xF)
/* 4335 GCI Intstatus(Mask)/WakeMask Register bits. */
#define GCI_INTSTATUS_RBI (1 << 0) /* Rx Break Interrupt */
#define GCI_INTSTATUS_UB (1 << 1) /* UART Break Interrupt */
#define GCI_INTSTATUS_SPE (1 << 2) /* SECI Parity Error Interrupt */
#define GCI_INTSTATUS_SFE (1 << 3) /* SECI Framing Error Interrupt */
#define GCI_INTSTATUS_SRITI (1 << 9) /* SECI Rx Idle Timer Interrupt */
#define GCI_INTSTATUS_STFF (1 << 10) /* SECI Tx FIFO Full Interrupt */
#define GCI_INTSTATUS_STFAE (1 << 11) /* SECI Tx FIFO Almost Empty Intr */
#define GCI_INTSTATUS_SRFAF (1 << 12) /* SECI Rx FIFO Almost Full */
#define GCI_INTSTATUS_SRFNE (1 << 14) /* SECI Rx FIFO Not Empty */
#define GCI_INTSTATUS_SRFOF (1 << 15) /* SECI Rx FIFO Not Empty Timeout */
#define GCI_INTSTATUS_GPIOINT (1 << 25) /* GCIGpioInt */
#define GCI_INTSTATUS_GPIOWAKE (1 << 26) /* GCIGpioWake */
/* 4335 GCI IntMask Register bits. */
#define GCI_INTMASK_RBI (1 << 0) /* Rx Break Interrupt */
#define GCI_INTMASK_UB (1 << 1) /* UART Break Interrupt */
#define GCI_INTMASK_SPE (1 << 2) /* SECI Parity Error Interrupt */
#define GCI_INTMASK_SFE (1 << 3) /* SECI Framing Error Interrupt */
#define GCI_INTMASK_SRITI (1 << 9) /* SECI Rx Idle Timer Interrupt */
#define GCI_INTMASK_STFF (1 << 10) /* SECI Tx FIFO Full Interrupt */
#define GCI_INTMASK_STFAE (1 << 11) /* SECI Tx FIFO Almost Empty Intr */
#define GCI_INTMASK_SRFAF (1 << 12) /* SECI Rx FIFO Almost Full */
#define GCI_INTMASK_SRFNE (1 << 14) /* SECI Rx FIFO Not Empty */
#define GCI_INTMASK_SRFOF (1 << 15) /* SECI Rx FIFO Not Empty Timeout */
#define GCI_INTMASK_GPIOINT (1 << 25) /* GCIGpioInt */
#define GCI_INTMASK_GPIOWAKE (1 << 26) /* GCIGpioWake */
/* 4335 GCI WakeMask Register bits. */
#define GCI_WAKEMASK_RBI (1 << 0) /* Rx Break Interrupt */
#define GCI_WAKEMASK_UB (1 << 1) /* UART Break Interrupt */
#define GCI_WAKEMASK_SPE (1 << 2) /* SECI Parity Error Interrupt */
#define GCI_WAKEMASK_SFE (1 << 3) /* SECI Framing Error Interrupt */
#define GCI_WAKE_SRITI (1 << 9) /* SECI Rx Idle Timer Interrupt */
#define GCI_WAKEMASK_STFF (1 << 10) /* SECI Tx FIFO Full Interrupt */
#define GCI_WAKEMASK_STFAE (1 << 11) /* SECI Tx FIFO Almost Empty Intr */
#define GCI_WAKEMASK_SRFAF (1 << 12) /* SECI Rx FIFO Almost Full */
#define GCI_WAKEMASK_SRFNE (1 << 14) /* SECI Rx FIFO Not Empty */
#define GCI_WAKEMASK_SRFOF (1 << 15) /* SECI Rx FIFO Not Empty Timeout */
#define GCI_WAKEMASK_GPIOINT (1 << 25) /* GCIGpioInt */
#define GCI_WAKEMASK_GPIOWAKE (1 << 26) /* GCIGpioWake */
#define GCI_WAKE_ON_GCI_GPIO1 1
#define GCI_WAKE_ON_GCI_GPIO2 2
#define GCI_WAKE_ON_GCI_GPIO3 3
#define GCI_WAKE_ON_GCI_GPIO4 4
#define GCI_WAKE_ON_GCI_GPIO5 5
#define GCI_WAKE_ON_GCI_GPIO6 6
#define GCI_WAKE_ON_GCI_GPIO7 7
#define GCI_WAKE_ON_GCI_GPIO8 8
#define GCI_WAKE_ON_GCI_SECI_IN 9
/* 4335 MUX options. each nibble belongs to a setting. Non-zero value specifies a logic
* for now only UART for bootloader.
*/
#define MUXENAB4335_UART_MASK (0x0000000f)
#define MUXENAB4335_UART_SHIFT 0
#define MUXENAB4335_HOSTWAKE_MASK (0x000000f0) /* configure GPIO for SDIO host_wake */
#define MUXENAB4335_HOSTWAKE_SHIFT 4
#define MUXENAB4335_GETIX(val, name) \
((((val) & MUXENAB4335_ ## name ## _MASK) >> MUXENAB4335_ ## name ## _SHIFT) - 1)
/*
* Maximum delay for the PMU state transition in us.
* This is an upper bound intended for spinwaits etc.
*/
#define PMU_MAX_TRANSITION_DLY 15000
/* PMU resource up transition time in ILP cycles */
#define PMURES_UP_TRANSITION 2
/* SECI configuration */
#define SECI_MODE_UART 0x0
#define SECI_MODE_SECI 0x1
#define SECI_MODE_LEGACY_3WIRE_BT 0x2
#define SECI_MODE_LEGACY_3WIRE_WLAN 0x3
#define SECI_MODE_HALF_SECI 0x4
#define SECI_RESET (1 << 0)
#define SECI_RESET_BAR_UART (1 << 1)
#define SECI_ENAB_SECI_ECI (1 << 2)
#define SECI_ENAB_SECIOUT_DIS (1 << 3)
#define SECI_MODE_MASK 0x7
#define SECI_MODE_SHIFT 4 /* (bits 5, 6, 7) */
#define SECI_UPD_SECI (1 << 7)
#define SECI_SLIP_ESC_CHAR 0xDB
#define SECI_SIGNOFF_0 SECI_SLIP_ESC_CHAR
#define SECI_SIGNOFF_1 0
#define SECI_REFRESH_REQ 0xDA
/* seci clk_ctl_st bits */
#define CLKCTL_STS_SECI_CLK_REQ (1 << 8)
#define CLKCTL_STS_SECI_CLK_AVAIL (1 << 24)
#define SECI_UART_MSR_CTS_STATE (1 << 0)
#define SECI_UART_MSR_RTS_STATE (1 << 1)
#define SECI_UART_SECI_IN_STATE (1 << 2)
#define SECI_UART_SECI_IN2_STATE (1 << 3)
/* GCI RX FIFO Control Register */
#define GCI_RXF_LVL_MASK (0xFF << 0)
#define GCI_RXF_TIMEOUT_MASK (0xFF << 8)
/* GCI UART Registers' Bit definitions */
/* Seci Fifo Level Register */
#define SECI_TXF_LVL_MASK (0x3F << 8)
#define TXF_AE_LVL_DEFAULT 0x4
#define SECI_RXF_LVL_FC_MASK (0x3F << 16)
/* SeciUARTFCR Bit definitions */
#define SECI_UART_FCR_RFR (1 << 0)
#define SECI_UART_FCR_TFR (1 << 1)
#define SECI_UART_FCR_SR (1 << 2)
#define SECI_UART_FCR_THP (1 << 3)
#define SECI_UART_FCR_AB (1 << 4)
#define SECI_UART_FCR_ATOE (1 << 5)
#define SECI_UART_FCR_ARTSOE (1 << 6)
#define SECI_UART_FCR_ABV (1 << 7)
#define SECI_UART_FCR_ALM (1 << 8)
/* SECI UART LCR register bits */
#define SECI_UART_LCR_STOP_BITS (1 << 0) /* 0 - 1bit, 1 - 2bits */
#define SECI_UART_LCR_PARITY_EN (1 << 1)
#define SECI_UART_LCR_PARITY (1 << 2) /* 0 - odd, 1 - even */
#define SECI_UART_LCR_RX_EN (1 << 3)
#define SECI_UART_LCR_LBRK_CTRL (1 << 4) /* 1 => SECI_OUT held low */
#define SECI_UART_LCR_TXO_EN (1 << 5)
#define SECI_UART_LCR_RTSO_EN (1 << 6)
#define SECI_UART_LCR_SLIPMODE_EN (1 << 7)
#define SECI_UART_LCR_RXCRC_CHK (1 << 8)
#define SECI_UART_LCR_TXCRC_INV (1 << 9)
#define SECI_UART_LCR_TXCRC_LSBF (1 << 10)
#define SECI_UART_LCR_TXCRC_EN (1 << 11)
#define SECI_UART_LCR_RXSYNC_EN (1 << 12)
#define SECI_UART_MCR_TX_EN (1 << 0)
#define SECI_UART_MCR_PRTS (1 << 1)
#define SECI_UART_MCR_SWFLCTRL_EN (1 << 2)
#define SECI_UART_MCR_HIGHRATE_EN (1 << 3)
#define SECI_UART_MCR_LOOPBK_EN (1 << 4)
#define SECI_UART_MCR_AUTO_RTS (1 << 5)
#define SECI_UART_MCR_AUTO_TX_DIS (1 << 6)
#define SECI_UART_MCR_BAUD_ADJ_EN (1 << 7)
#define SECI_UART_MCR_XONOFF_RPT (1 << 9)
/* SeciUARTLSR Bit Mask */
#define SECI_UART_LSR_RXOVR_MASK (1 << 0)
#define SECI_UART_LSR_RFF_MASK (1 << 1)
#define SECI_UART_LSR_TFNE_MASK (1 << 2)
#define SECI_UART_LSR_TI_MASK (1 << 3)
#define SECI_UART_LSR_TPR_MASK (1 << 4)
#define SECI_UART_LSR_TXHALT_MASK (1 << 5)
/* SeciUARTMSR Bit Mask */
#define SECI_UART_MSR_CTSS_MASK (1 << 0)
#define SECI_UART_MSR_RTSS_MASK (1 << 1)
#define SECI_UART_MSR_SIS_MASK (1 << 2)
#define SECI_UART_MSR_SIS2_MASK (1 << 3)
/* SeciUARTData Bits */
#define SECI_UART_DATA_RF_NOT_EMPTY_BIT (1 << 12)
#define SECI_UART_DATA_RF_FULL_BIT (1 << 13)
#define SECI_UART_DATA_RF_OVRFLOW_BIT (1 << 14)
#define SECI_UART_DATA_FIFO_PTR_MASK 0xFF
#define SECI_UART_DATA_RF_RD_PTR_SHIFT 16
#define SECI_UART_DATA_RF_WR_PTR_SHIFT 24
/* LTECX: ltecxmux */
#define LTECX_EXTRACT_MUX(val, idx) (getbit4(&(val), (idx)))
/* LTECX: ltecxmux MODE */
#define LTECX_MUX_MODE_IDX 0
#define LTECX_MUX_MODE_WCI2 0x0
#define LTECX_MUX_MODE_GPIO 0x1
/* LTECX GPIO Information Index */
#define LTECX_NVRAM_FSYNC_IDX 0
#define LTECX_NVRAM_LTERX_IDX 1
#define LTECX_NVRAM_LTETX_IDX 2
#define LTECX_NVRAM_WLPRIO_IDX 3
/* LTECX WCI2 Information Index */
#define LTECX_NVRAM_WCI2IN_IDX 0
#define LTECX_NVRAM_WCI2OUT_IDX 1
/* LTECX: Macros to get GPIO/FNSEL/GCIGPIO */
#define LTECX_EXTRACT_PADNUM(val, idx) (getbit8(&(val), (idx)))
#define LTECX_EXTRACT_FNSEL(val, idx) (getbit4(&(val), (idx)))
#define LTECX_EXTRACT_GCIGPIO(val, idx) (getbit4(&(val), (idx)))
/* WLAN channel numbers - used from wifi.h */
/* WLAN BW */
#define ECI_BW_20 0x0
#define ECI_BW_25 0x1
#define ECI_BW_30 0x2
#define ECI_BW_35 0x3
#define ECI_BW_40 0x4
#define ECI_BW_45 0x5
#define ECI_BW_50 0x6
#define ECI_BW_ALL 0x7
/* WLAN - number of antenna */
#define WLAN_NUM_ANT1 TXANT_0
#define WLAN_NUM_ANT2 TXANT_1
/* otpctrl1 0xF4 */
#define OTPC_FORCE_PWR_OFF 0x02000000
/* chipcommon s/r registers introduced with cc rev >= 48 */
#define CC_SR_CTL0_ENABLE_MASK 0x1
#define CC_SR_CTL0_ENABLE_SHIFT 0
#define CC_SR_CTL0_EN_SR_ENG_CLK_SHIFT 1 /* sr_clk to sr_memory enable */
#define CC_SR_CTL0_RSRC_TRIGGER_SHIFT 2 /* Rising edge resource trigger 0 to sr_engine */
#define CC_SR_CTL0_MIN_DIV_SHIFT 6 /* Min division value for fast clk in sr_engine */
#define CC_SR_CTL0_EN_SBC_STBY_SHIFT 16 /* Allow Subcore mem StandBy? */
#define CC_SR_CTL0_EN_SR_ALP_CLK_MASK_SHIFT 18
#define CC_SR_CTL0_EN_SR_HT_CLK_SHIFT 19
#define CC_SR_CTL0_ALLOW_PIC_SHIFT 20 /* Allow pic to separate power domains */
#define CC_SR_CTL0_MAX_SR_LQ_CLK_CNT_SHIFT 25
#define CC_SR_CTL0_EN_MEM_DISABLE_FOR_SLEEP 30
#define CC_SR_CTL1_SR_INIT_MASK 0x3FF
#define CC_SR_CTL1_SR_INIT_SHIFT 0
#define ECI_INLO_PKTDUR_MASK 0x000000f0 /* [7:4] - 4 bits */
#define ECI_INLO_PKTDUR_SHIFT 4
/* gci chip control bits */
#define GCI_GPIO_CHIPCTRL_ENAB_IN_BIT 0
#define GCI_GPIO_CHIPCTRL_ENAB_OP_BIT 1
#define GCI_GPIO_CHIPCTRL_INVERT_BIT 2
#define GCI_GPIO_CHIPCTRL_PULLUP_BIT 3
#define GCI_GPIO_CHIPCTRL_PULLDN_BIT 4
#define GCI_GPIO_CHIPCTRL_ENAB_BTSIG_BIT 5
#define GCI_GPIO_CHIPCTRL_ENAB_OD_OP_BIT 6
#define GCI_GPIO_CHIPCTRL_ENAB_EXT_GPIO_BIT 7
/* gci GPIO input status bits */
#define GCI_GPIO_STS_VALUE_BIT 0
#define GCI_GPIO_STS_POS_EDGE_BIT 1
#define GCI_GPIO_STS_NEG_EDGE_BIT 2
#define GCI_GPIO_STS_FAST_EDGE_BIT 3
#define GCI_GPIO_STS_CLEAR 0xF
#define GCI_GPIO_STS_VALUE (1 << GCI_GPIO_STS_VALUE_BIT)
#endif /* _SBCHIPC_H */