nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
I updated all versions to the newest one that's used anywhere.
Then at least the straing can be found with full text search.
It's another step towards understanding and unifying the CI environment.
Having newline between I think didn't apply the PR stale days setting of
30 properly (it was using 45)
And it seemd that unless I set the days-before-close to -1
intentionally, it would still close the Issue/PRs, as the default value
is 7 already.
Also updated version of the stale action to v8
* Remove old stale bot yaml file
* Remove slack svg file (unused)
* Stale action: Only apply stale label, and no other actions
Respecting the opinion on
fa9ac6ecf6,
it seems reasonable to disable commenting feature, and just keep the
action only applying the `stale` label. This will reduce the noise /
email spams / ping pong fight with the stale bot (Action)
- use `gazebo-classic` everywhere consistently referring to the original Gazebo (eg version 9,10,11)
- additional `gazebo_*` helper targets added for compatibility, but warn about deprecation and tell you the new target naming
- use `gz` everywhere when referring to Gazebo (aka Ignition Gazebo or new Gazebo)
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
known issues:
- flash-based params does not work on H7 (due to ECC), so params are on
SD card. The last flash sector is still reserved however.
- output channel 6 does not support DShot (the implementation does not
handle channel gaps)
- flashing of the 2. flash bank is much slower (around 3x), than the 1.
bank for some unknown reason.
- after the BL jumps to the app, there's several seconds passing until
stm32_boardinitialize() is called.
So instead of fuzzing each and every PR for 10minutes, we just fuzz
30mins every 24 hours, at 6am UTC which should be a time when US and
Europe might be least active.
Github constructs the workflow names from the
matrix configurations. Having latitude and longitude
in the fist columns makes these names rather cryptic.
Alex Klimaj
Alexis Guijarro
Beat Küng
Christian Rauch
David Sidrane
Beniamino Pozzan
comla-x
Junwoo Hwang
Matthias Grob
Ramon Roche
Julian Oes
Daniel Agar
Peter van der Perk
Justin
achim
Kirill Shilov
dirksavage88
alessandro
Viktor Vladic
Vatsal Asitkumar Joshi