px4-firmware/msg/manual_control_setpoint.msg

68 lines
3.7 KiB
Plaintext
Raw Normal View History

2018-08-07 10:42:32 -03:00
uint64 timestamp # time since system start (microseconds)
2014-12-08 06:06:56 -04:00
uint8 SWITCH_POS_NONE = 0 # switch is not mapped
2018-08-07 10:42:32 -03:00
uint8 SWITCH_POS_ON = 1 # switch activated (value = 1)
2014-12-08 06:06:56 -04:00
uint8 SWITCH_POS_MIDDLE = 2 # middle position (value = 0)
uint8 SWITCH_POS_OFF = 3 # switch not activated (value = -1)
uint8 MODE_SLOT_NONE = 0 # no mode slot assigned
uint8 MODE_SLOT_1 = 1 # mode slot 1 selected
uint8 MODE_SLOT_2 = 2 # mode slot 2 selected
uint8 MODE_SLOT_3 = 3 # mode slot 3 selected
uint8 MODE_SLOT_4 = 4 # mode slot 4 selected
uint8 MODE_SLOT_5 = 5 # mode slot 5 selected
uint8 MODE_SLOT_6 = 6 # mode slot 6 selected
uint8 MODE_SLOT_NUM = 6 # number of slots
uint8 SOURCE_RC = 1 # radio control
uint8 SOURCE_MAVLINK_0 = 2 # mavlink instance 0
uint8 SOURCE_MAVLINK_1 = 3 # mavlink instance 1
uint8 SOURCE_MAVLINK_2 = 4 # mavlink instance 2
uint8 SOURCE_MAVLINK_3 = 5 # mavlink instance 4
2014-12-08 06:06:56 -04:00
# Any of the channels may not be available and be set to NaN
# to indicate that it does not contain valid data.
# The variable names follow the definition of the
# MANUAL_CONTROL mavlink message.
# The default range is from -1 to 1 (mavlink message -1000 to 1000)
# The range for the z variable is defined from 0 to 1. (The z field of
# the MANUAL_CONTROL mavlink message is defined from -1000 to 1000)
float32 x # stick position in x direction -1..1
# in general corresponds to forward/back motion or pitch of vehicle,
# in general a positive value means forward or negative pitch and
# a negative value means backward or positive pitch
float32 y # stick position in y direction -1..1
# in general corresponds to right/left motion or roll of vehicle,
# in general a positive value means right or positive roll and
# a negative value means left or negative roll
float32 z # throttle stick position 0..1
# in general corresponds to up/down motion or thrust of vehicle,
# in general the value corresponds to the demanded throttle by the user,
# if the input is used for setting the setpoint of a vertical position
# controller any value > 0.5 means up and any value < 0.5 means down
float32 r # yaw stick/twist position, -1..1
2014-12-08 06:06:56 -04:00
# in general corresponds to the righthand rotation around the vertical
# (downwards) axis of the vehicle
float32 flaps # flap position
float32 aux1 # default function: camera yaw / azimuth
float32 aux2 # default function: camera pitch / tilt
float32 aux3 # default function: camera trigger
float32 aux4 # default function: camera roll
float32 aux5 # default function: payload drop
float32 aux6
2014-12-08 06:06:56 -04:00
uint8 mode_switch # main mode 3 position switch (mandatory): _MANUAL_, ASSIST, AUTO
uint8 return_switch # return to launch 2 position switch (mandatory): _NORMAL_, RTL
2015-12-19 00:21:51 -04:00
uint8 rattitude_switch # rattitude control 2 position switch (optional): _MANUAL, RATTITUDE
2014-12-08 06:06:56 -04:00
uint8 posctl_switch # position control 2 position switch (optional): _ALTCTL_, POSCTL
uint8 loiter_switch # loiter 2 position switch (optional): _MISSION_, LOITER
uint8 acro_switch # acro 2 position switch (optional): _MANUAL_, ACRO
uint8 offboard_switch # offboard 2 position switch (optional): _NORMAL_, OFFBOARD
2015-12-19 00:21:51 -04:00
uint8 kill_switch # throttle kill: _NORMAL_, KILL
uint8 arm_switch # arm/disarm switch: _DISARMED_, ARMED
2016-07-19 06:37:54 -03:00
uint8 transition_switch # VTOL transition switch: _HOVER, FORWARD_FLIGHT
uint8 gear_switch # landing gear switch: _DOWN_, UP
uint8 mode_slot # the slot a specific model selector is in
uint8 data_source # where this input is coming from
uint8 stab_switch # stabilize switch (only relevant for fixed wings, optional): _MANUAL, STABILIZED
uint8 man_switch # manual switch (only relevant for fixed wings, optional): _STABILIZED_, MANUAL