mirror of https://github.com/ArduPilot/ardupilot
167 lines
3.5 KiB
Plaintext
167 lines
3.5 KiB
Plaintext
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
# for TMH7 hardware.
|
|
# thanks to betaflight for pin information
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1138
|
|
|
|
# crystal frequency, setup to use external oscillator
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
MCU_CLOCKRATE_MHZ 480
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# bootloader takes first sector
|
|
FLASH_RESERVE_START_KB 384
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
define STORAGE_FLASH_PAGE 1
|
|
|
|
STM32_ST_USE_TIMER 2
|
|
|
|
# SPI devices
|
|
|
|
# SPI1
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# SPI2
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
# SPI3
|
|
PB2 SPI3_MOSI SPI3
|
|
PC10 SPI3_SCK SPI3
|
|
PC11 SPI3_MISO SPI3
|
|
|
|
# SPI4
|
|
PE12 SPI4_SCK SPI4
|
|
PE13 SPI4_MISO SPI4
|
|
PE14 SPI4_MOSI SPI4
|
|
|
|
# Chip select pins
|
|
PA15 FLASH1_CS CS
|
|
PB12 OSD1_CS CS
|
|
PA4 GYRO1_CS CS
|
|
PE11 GYRO2_CS CS
|
|
|
|
# Beeper
|
|
PE3 BUZZER OUTPUT GPIO(80) LOW
|
|
define HAL_BUZZER_PIN 80
|
|
|
|
# SERIAL ports
|
|
SERIAL_ORDER OTG1 USART1 EMPTY USART3 EMPTY UART5 USART6 UART7 UART8
|
|
# PA10 IO-debug-console
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# USART1 (ESC Telemetry)
|
|
PA10 USART1_RX USART1 NODMA
|
|
DEFAULT_SERIAL1_PROTOCOL SerialProtocol_ESCTelemetry
|
|
|
|
# UART3
|
|
PD8 USART3_TX USART3 NODMA
|
|
PD9 USART3_RX USART3 NODMA
|
|
DEFAULT_SERIAL3_PROTOCOL SerialProtocol_None
|
|
|
|
# UART5 (GPS)
|
|
PC12 UART5_TX UART5
|
|
PD2 UART5_RX UART5
|
|
DEFAULT_SERIAL5_PROTOCOL SerialProtocol_GPS
|
|
|
|
# USART6 (RX)
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
DEFAULT_SERIAL6_PROTOCOL SerialProtocol_RCIN
|
|
|
|
# UART7 (DJI)
|
|
PE7 UART7_RX UART7
|
|
PE8 UART7_TX UART7
|
|
define DEFAULT_SERIAL7_PROTOCOL SerialProtocol_DJI_FPV
|
|
|
|
# UART8 (SBUS/SmartAudio)
|
|
PE0 UART8_RX UART8 # no suitable timer for RCININT
|
|
PE1 UART8_TX UART8
|
|
|
|
# I2C ports
|
|
I2C_ORDER I2C1
|
|
# I2C1
|
|
PB6 I2C1_SCL I2C1
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
# One baro
|
|
BARO DPS310 I2C:0:0x76
|
|
|
|
# Servos
|
|
PB8 CAMERA1 OUTPUT GPIO(70) LOW
|
|
define RELAY2_PIN_DEFAULT 70
|
|
|
|
# ADC ports
|
|
|
|
# ADC1
|
|
PC1 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
define HAL_BATT_VOLT_PIN 11
|
|
define HAL_BATT_VOLT_SCALE 11.0
|
|
PC2 RSSI_ADC ADC1
|
|
define BOARD_RSSI_ANA_PIN 12
|
|
PC3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
define HAL_BATT_CURR_PIN 13
|
|
define HAL_BATT_CURR_SCALE 50.0
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
|
|
# MOTORS
|
|
PA0 TIM5_CH1 TIM5 PWM(1) GPIO(50) BIDIR # M1
|
|
PA1 TIM5_CH2 TIM5 PWM(2) GPIO(51) # M2
|
|
PA2 TIM5_CH3 TIM5 PWM(3) GPIO(52) BIDIR # M3
|
|
PA3 TIM5_CH4 TIM5 PWM(4) GPIO(53) # M4
|
|
|
|
# LEDs
|
|
PA8 TIM1_CH1 TIM1 PWM(9) GPIO(58) # M9
|
|
|
|
PE5 LED1 OUTPUT LOW GPIO(91)
|
|
define HAL_GPIO_A_LED_PIN 91
|
|
|
|
PE4 LED2 OUTPUT LOW GPIO(92)
|
|
define HAL_GPIO_B_LED_PIN 92
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
# Dataflash setup
|
|
SPIDEV dataflash SPI3 DEVID1 FLASH1_CS MODE3 104*MHZ 104*MHZ
|
|
|
|
define HAL_LOGGING_DATAFLASH_ENABLED 1
|
|
|
|
# OSD setup
|
|
SPIDEV osd SPI2 DEVID1 OSD1_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
define OSD_ENABLED 1
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
# IMU setup
|
|
SPIDEV icm42688 SPI1 DEVID1 GYRO1_CS MODE3 1*MHZ 16*MHZ
|
|
SPIDEV bmi270 SPI4 DEVID1 GYRO2_CS MODE3 1*MHZ 8*MHZ
|
|
|
|
IMU BMI270 SPI:bmi270 ROTATION_PITCH_180_YAW_90
|
|
IMU Invensensev3 SPI:icm42688 ROTATION_PITCH_180_YAW_90
|
|
|
|
DMA_NOSHARE TIM5_UP TIM3_UP TIM8_UP SPI1* SPI4*
|
|
DMA_PRIORITY TIM5_UP TIM3_UP TIM8_UP SPI1* SPI4*
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
# external compass types
|
|
define ALLOW_ARM_NO_COMPASS
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 3
|
|
# Motor order implies Betaflight/X for standard ESCs
|
|
define HAL_FRAME_TYPE_DEFAULT 12
|
|
define AP_SCRIPTING_ENABLED 0
|