6.2 KiB

Raw Blame History

A6 Flight Controller

The A6 flight controller is manufactured and sold by YJUAV.

The full schematics of the board are available here:

https://github.com/yunjiuav/Hardware/tree/main/A6

Features

STM32H743 microcontroller
Three IMUs: ICM42688, ICM42688 and IIM42652
Internal RM3100 SPI magnetometer
Internal DPS310 SPI barometer
Internal vibration isolation for IMUs
Internal RGB LED
microSD card slot port
2 power ports(CAN and Analog)
6 UARTs and USB ports
3 I2C and 3 CAN ports
14 PWM output ports
Safety switch port
External SPI port
Buzzer port
RC IN port

Pinout

Connectors

ADC

Pin	Signal	Volt
1	VCC	+5V
2	ADC_3V3	+3.3V
3	ADC_6V6	+6.6V
4	GND	GND

DEBUG

Pin	Signal	Volt
1	VCC	+5V
2	TX	+3.3V
3	RX	+3.3V
4	SWDIO	+3.3V
5	SWCLK	+3.3V
6	GND	GND

RSSI&SBUS

Pin	Signal	Volt
1	VCC	+5V
2	RSSI	+3.3V
3	SBUS_OUT	+3.3V
4	GND	GND

SAFETY

Pin	Signal	Volt
1	3V3_OUT	+3.3V
2	SAFETY_SW	+3.3V
3	SAFETY_SW_LED	+3.3V
4	GND	GND

SPI3

Pin	Signal	Volt
1	VCC	+5V
2	SPI_SCK	+3.3V
3	SPI_MISO	+3.3V
4	SPI_MOSI	+3.3V
5	SPI_CS	+3.3V
6	GND	GND

I2C4

Pin	Signal	Volt
1	VCC	+5V
2	I2C_SCL	+3.3V
3	I2C_SDA	+3.3V
4	GND	GND

USB EX

Pin	Signal	Volt
1	VCC_IN	+5V
2	DM	+3.3V
3	DP	+3.3V
4	GND	GND

CAN1&CAN2

Pin	Signal	Volt
1	VCC	+5V
2	CAN_P	+3.3V
3	CAN_N	+3.3V
4	GND	GND

GPS1&SAFETY

Pin	Signal	Volt
1	VCC	+5V
2	UART_TX	+3.3V
3	UART_RX	+3.3V
4	I2C_SCL	+3.3V
5	I2C_SDA	+3.3V
6	SAFETY_SW	+3.3V
7	SAFETY_SW_LED	+3.3V
8	3V3_OUT	+3.3V
9	BUZZER	+3.3V
10	GND	GND

TELEM1&TELEM2

Pin	Signal	Volt
1	VCC	+5V
2	UART_TX	+3.3V
3	UART_RX	+3.3V
4	NC	-
5	NC	-
6	GND	GND

GPS2

Pin	Signal	Volt
1	VCC	+5V
2	UART_TX	+3.3V
3	UART_RX	+3.3V
4	I2C_SCL	+3.3V
5	I2C_SDA	+3.3V
6	GND	GND

POWER A

Pin	Signal	Volt
1	VCC_IN	+5V
2	VCC_IN	+5V
3	BAT_CRRENT_ADC	+3.3V
4	BAT_VOLTAGE_ADC	+3.3V
5	GND	GND
6	GND	GND

POWER C

Pin	Signal	Volt
1	VCC_IN	+5V
2	VCC_IN	+5V
3	CAN_P	+3.3V
4	CAN_N	+3.3V
5	GND	GND
6	GND	GND

UART Mapping

SERIAL0 -> USB(OTG1)
SERIAL1 -> USART1(Telem1)
SERIAL2 -> USART2 (Telem2)
SERIAL3 -> USART3 (GPS1), NODMA
SERIAL4 -> UART5 (GPS2), NODMA
SERIAL5 -> UART6 (SBUS)
SERIAL6 -> UART7 (Debug), NODMA
SERIAL7 -> USB2(OTG2)

RC Input

The remote control signal should be connected to the “RC IN” pin, at one side of the servo channels.

This signal pin supports two types of remote control signal inputs, SBUS and PPM signals.

PWM Output

The A6 supports up to 14 PWM outputs,support all PWM protocols as well as DShot. All 14 PWM outputs have GND on the bottom row, 5V on the middle row and signal on the top row.

The 14 PWM outputs are in 4 groups:

PWM 1, 2, 3 and 4 in group1
PWM 5, 6, 7 and 8 in group2
PWM 9, 10, 11 and 12 in group3
PWM 13 and 14 group4

Channels 1-8 support bi-directional Dshot, channels 9-12 support Dshot, channels 13-14 support regular PWM. Channels within the same group need to use the same output rate. If any channel in a group uses DShot, then all channels in that group need to use DShot.

Battery Monitoring

The A6 flight controller has two six-pin power connectors, supporting CAN interface power supply and analog interface power supply.

Compass

The A6 flight controller built-in industrial-grade electronic compass chip RM3100.

GPIOs

All 14 PWM channels can be used for GPIO functions (relays, buttons, RPM etc).

The pin numbers for these PWM channels in ArduPilot are shown below:

PWM Channels	Pin	PWM Channels	Pin
PWM1	50	PWM8	57
PWM2	51	PWM9	58
PWM3	52	PWM10	59
PWM4	53	PWM11	60
PWM5	54	PWM12	61
PWM6	55	PWM13	62
PWM7	56	PWM14	63

Analog inputs

The A6 flight controller has 5 analog inputs

ADC Pin10 -> Battery Current
ADC Pin11 -> Battery Voltage
ADC Pin4 -> ADC 3V3 Sense
ADC Pin8 -> ADC 5V Sense
ADC Pin18 -> RSSI voltage monitoring

Build the FC

./waf configure --board=YJUAV_A6 ./waf copter

The compiled firmware is located in folder "build/YJUAV_A6/bin/arducopter.apj".

Loading Firmware

The A6 flight controller comes pre-installed with an ArduPilot compatible bootloader, allowing the loading of *.apj firmware files with any ArduPilot compatible ground station.

6.2 KiB Raw Blame History