mirror of https://github.com/ArduPilot/ardupilot
69 lines
2.6 KiB
C++
69 lines
2.6 KiB
C++
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
/// @file AP_MotorsTri.h
|
|
/// @brief Motor control class for Tricopters
|
|
|
|
#ifndef __AP_MOTORS_TRI_H__
|
|
#define __AP_MOTORS_TRI_H__
|
|
|
|
#include <AP_Common/AP_Common.h>
|
|
#include <AP_Math/AP_Math.h> // ArduPilot Mega Vector/Matrix math Library
|
|
#include <RC_Channel/RC_Channel.h> // RC Channel Library
|
|
#include "AP_MotorsMulticopter.h"
|
|
|
|
// tail servo uses channel 7
|
|
#define AP_MOTORS_CH_TRI_YAW CH_7
|
|
|
|
/// @class AP_MotorsTri
|
|
class AP_MotorsTri : public AP_MotorsMulticopter {
|
|
public:
|
|
|
|
/// Constructor
|
|
AP_MotorsTri(uint16_t loop_rate, uint16_t speed_hz = AP_MOTORS_SPEED_DEFAULT) :
|
|
AP_MotorsMulticopter(loop_rate, speed_hz)
|
|
{
|
|
AP_Param::setup_object_defaults(this, var_info);
|
|
};
|
|
|
|
// init
|
|
virtual void Init();
|
|
|
|
// set update rate to motors - a value in hertz
|
|
void set_update_rate( uint16_t speed_hz );
|
|
|
|
// enable - starts allowing signals to be sent to motors
|
|
virtual void enable();
|
|
|
|
// output_test - spin a motor at the pwm value specified
|
|
// motor_seq is the motor's sequence number from 1 to the number of motors on the frame
|
|
// pwm value is an actual pwm value that will be output, normally in the range of 1000 ~ 2000
|
|
virtual void output_test(uint8_t motor_seq, int16_t pwm);
|
|
|
|
// output_min - sends minimum values out to the motors
|
|
virtual void output_min();
|
|
|
|
// get_motor_mask - returns a bitmask of which outputs are being used for motors or servos (1 means being used)
|
|
// this can be used to ensure other pwm outputs (i.e. for servos) do not conflict
|
|
virtual uint16_t get_motor_mask();
|
|
|
|
// var_info for holding Parameter information
|
|
static const struct AP_Param::GroupInfo var_info[];
|
|
|
|
protected:
|
|
// output - sends commands to the motors
|
|
void output_armed_stabilizing();
|
|
void output_armed_not_stabilizing();
|
|
void output_disarmed();
|
|
|
|
// calc_yaw_radio_output - calculate final radio output for yaw channel
|
|
int16_t calc_yaw_radio_output(); // calculate radio output for yaw servo, typically in range of 1100-1900
|
|
|
|
// parameters
|
|
AP_Int8 _yaw_servo_reverse; // Yaw servo signal reversing
|
|
AP_Int16 _yaw_servo_trim; // Trim or center position of yaw servo
|
|
AP_Int16 _yaw_servo_min; // Minimum angle limit of yaw servo
|
|
AP_Int16 _yaw_servo_max; // Maximum angle limit of yaw servo
|
|
};
|
|
|
|
#endif // AP_MOTORSTRI
|