ardupilot/libraries/AP_HAL_ChibiOS/hwdef/HolybroGPS/hwdef.dat

183 lines
3.3 KiB
Plaintext

# hw definition file for processing by chibios_pins.py
# MCU class and specific type
# MCU class and specific type
MCU STM32F4xx STM32F412Rx
# bootloader starts firmware at 64k
FLASH_RESERVE_START_KB 64
# store parameters in pages 2 and 3
define STORAGE_FLASH_PAGE 2
define HAL_STORAGE_SIZE 8192
# board ID for firmware load
APJ_BOARD_ID 1035
# setup build for a peripheral firmware
env AP_PERIPH 1
STM32_ST_USE_TIMER 5
# enable watchdog
define HAL_WATCHDOG_ENABLED_DEFAULT true
# crystal frequency
OSCILLATOR_HZ 16000000
define CH_CFG_ST_FREQUENCY 1000000
# assume 512k flash part
FLASH_SIZE_KB 512
# debug on USART2
STDOUT_SERIAL SD2
STDOUT_BAUDRATE 57600
# order of UARTs
SERIAL_ORDER USART2 USART1
# sensor power control
PC15 VDD_3V3_SENSORS_EN OUTPUT HIGH
# LEDs
PB15 LED OUTPUT HIGH GPIO(2) # blue
PA7 LED_R OUTPUT HIGH GPIO(0)
PB14 LED_G OUTPUT HIGH GPIO(1)
define HAL_GPIO_A_LED_PIN 0
define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2
define HAL_GPIO_LED_ON 0
define HAL_GPIO_LED_OFF 1
define HAL_HAVE_PIXRACER_LED
# USART1, GPS
PA9 USART1_TX USART1 NODMA
PA10 USART1_RX USART1 NODMA
# USART2, debug
PA2 USART2_TX USART2
PA3 USART2_RX USART2
# SWD debugging
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# I2C1 bus
PB7 I2C1_SDA I2C1
PB6 I2C1_SCL I2C1
# I2C2 bus
PB3 I2C2_SDA I2C2
PB10 I2C2_SCL I2C2
define HAL_I2C_INTERNAL_MASK 3
# I2C buses
I2C_ORDER I2C1 I2C2
# one SPI bus
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PB5 SPI1_MOSI SPI1
# SPI CS
PA8 ACC_CS CS
# version sense
PA0 HW_REV_SENSE INPUT
PA1 HW_VER_SENSE INPUT
PB1 HW_VER_REV_DRIVE INPUT
# GPS PPS
PA15 GPS_PPS_IN INPUT
# SPI devices
SPIDEV bmi088_a SPI1 DEVID1 ACC_CS MODE3 10*MHZ 10*MHZ
# compass
COMPASS BMM150 I2C:0:0x10 false ROTATION_YAW_90
# baro
BARO BMP388 I2C:0:0x77
# IMU
IMU BMI088 SPI:bmi055_a SPI:bmi055_g ROTATION_ROLL_180_YAW_90
define HAL_BARO_ALLOW_INIT_NO_BARO
define HAL_USE_ADC FALSE
define STM32_ADC_USE_ADC1 FALSE
define HAL_DISABLE_ADC_DRIVER TRUE
define HAL_NO_GPIO_IRQ
# avoid RCIN thread to save memory
define HAL_NO_RCIN_THREAD
define HAL_USE_RTC FALSE
define DISABLE_SERIAL_ESC_COMM TRUE
define NO_DATAFLASH TRUE
define DMA_RESERVE_SIZE 0
define PERIPH_FW TRUE
define HAL_DISABLE_LOOP_DELAY
# enable CAN support
PA11 CAN1_RX CAN1
PA12 CAN1_TX CAN1
PB2 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
PB12 CAN2_RX CAN2
PB13 CAN2_TX CAN2
PA4 GPIO_CAN2_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
# use DNA
define HAL_CAN_DEFAULT_NODE_ID 0
define CAN_APP_NODE_NAME "org.ardupilot.HolybroGPS"
define HAL_NO_GCS
define HAL_NO_LOGGING
define HAL_NO_MONITOR_THREAD
define HAL_MINIMIZE_FEATURES 0
define HAL_BUILD_AP_PERIPH
define HAL_DEVICE_THREAD_STACK 768
# we setup a small defaults.parm
define AP_PARAM_MAX_EMBEDDED_PARAM 256
# disable dual GPS and GPS blending to save flash space
define GPS_MAX_RECEIVERS 1
define GPS_MAX_INSTANCES 1
define HAL_COMPASS_MAX_SENSORS 1
# GPS+MAG+BARO+LEDs
define HAL_PERIPH_ENABLE_GPS
define HAL_PERIPH_ENABLE_MAG
define HAL_PERIPH_ENABLE_BARO
define HAL_PERIPH_ENABLE_NOTIFY
define HAL_PERIPH_ENABLE_RC_OUT
# GPS on 2nd port
define HAL_PERIPH_GPS_PORT_DEFAULT 1
# enable NCP5623 on 2nd I2C bus
define BUILD_DEFAULT_LED_TYPE 128
# use the app descriptor needed by MissionPlanner for CAN upload
env APP_DESCRIPTOR MissionPlanner
# reserve 256 bytes for comms between app and bootloader
RAM_RESERVE_START 256