ardupilot/libraries/AP_Motors/AP_MotorsHeli_RSC.h

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
#pragma once

#include <AP_Common/AP_Common.h>
#include <AP_Math/AP_Math.h>            // ArduPilot Mega Vector/Matrix math Library
#include <RC_Channel/RC_Channel.h>      // RC Channel Library

// rotor controller states
enum RotorControlState {
    ROTOR_CONTROL_STOP = 0,
    ROTOR_CONTROL_IDLE,
    ROTOR_CONTROL_ACTIVE
};

// rotor control modes
enum RotorControlMode {
    ROTOR_CONTROL_MODE_DISABLED = 0,
    ROTOR_CONTROL_MODE_SPEED_PASSTHROUGH,
    ROTOR_CONTROL_MODE_SPEED_SETPOINT,
    ROTOR_CONTROL_MODE_OPEN_LOOP_POWER_OUTPUT,
    ROTOR_CONTROL_MODE_CLOSED_LOOP_POWER_OUTPUT
};

class AP_MotorsHeli_RSC {
public:
    AP_MotorsHeli_RSC(RC_Channel_aux::Aux_servo_function_t aux_fn,
                      uint8_t default_channel,
                      uint16_t loop_rate) :
        _loop_rate(loop_rate),
        _aux_fn(aux_fn),
        _default_channel(default_channel)
    {};

    // init_servo - servo initialization on start-up
    void        init_servo();

    // set_control_mode - sets control mode
    void        set_control_mode(RotorControlMode mode) { _control_mode = mode; }

    // set_critical_speed
    void        set_critical_speed(float critical_speed) { _critical_speed = critical_speed; }
    
    // get_critical_speed
    float       get_critical_speed() const { return _critical_speed; }

    // set_idle_output
    float       get_idle_output() { return _idle_output; }
    void        set_idle_output(float idle_output) { _idle_output = idle_output; }

    // get_desired_speed
    float       get_desired_speed() const { return _desired_speed; }

    // set_desired_speed
    void        set_desired_speed(float desired_speed) { _desired_speed = desired_speed; }

    // get_control_speed
    float       get_control_output() const { return _control_output; }

    // get_rotor_speed - return estimated or measured rotor speed
    float       get_rotor_speed() const;

    // is_runup_complete
    bool        is_runup_complete() const { return _runup_complete; }

    // set_ramp_time
    void        set_ramp_time(int8_t ramp_time) { _ramp_time = ramp_time; }

    // set_runup_time
    void        set_runup_time(int8_t runup_time) { _runup_time = runup_time; }

    // set_power_output_range
    void        set_power_output_range(uint16_t power_low, uint16_t power_high);

    // set_motor_load
    void        set_motor_load(float load) { _load_feedforward = load; }

    // output - update value to send to ESC/Servo
    void        output(RotorControlState state);

private:

    // external variables
    float           _loop_rate;                 // main loop rate

    // channel setup for aux function
    RC_Channel_aux::Aux_servo_function_t _aux_fn;
    uint8_t         _default_channel;
    
    // internal variables
    RotorControlMode _control_mode = ROTOR_CONTROL_MODE_DISABLED;   // motor control mode, Passthrough or Setpoint
    float           _critical_speed = 0.0f;     // rotor speed below which flight is not possible
    float           _idle_output = 0.0f;        // motor output idle speed
    float           _desired_speed = 0.0f;      // latest desired rotor speed from pilot
    float           _control_output = 0.0f;     // latest logic controlled output
    float           _rotor_ramp_output = 0.0f;  // scalar used to ramp rotor speed between _rsc_idle_output and full speed (0.0-1.0f)
    float           _rotor_runup_output = 0.0f; // scalar used to store status of rotor run-up time (0.0-1.0f)
    int8_t          _ramp_time = 0;             // time in seconds for the output to the main rotor's ESC to reach full speed
    int8_t          _runup_time = 0;            // time in seconds for the main rotor to reach full speed.  Must be longer than _rsc_ramp_time
    bool            _runup_complete = false;    // flag for determining if runup is complete
    float           _power_output_low = 0.0f;   // setpoint for power output at minimum rotor power
    float           _power_output_high = 0.0f;  // setpoint for power output at maximum rotor power
    float           _power_output_range = 0.0f; // maximum range of output power
    float           _load_feedforward = 0.0f;   // estimate of motor load, range 0-1.0f

    // update_rotor_ramp - slews rotor output scalar between 0 and 1, outputs float scalar to _rotor_ramp_output
    void            update_rotor_ramp(float rotor_ramp_input);

    // update_rotor_runup - function to slew rotor runup scalar, outputs float scalar to _rotor_runup_ouptut
    void            update_rotor_runup();

    // write_rsc - outputs pwm onto output rsc channel. servo_out parameter is of the range 0 ~ 1
    void            write_rsc(float servo_out);
};