mirror of https://github.com/ArduPilot/ardupilot
166 lines
10 KiB
Markdown
166 lines
10 KiB
Markdown
* almost all code is fully rewritten
|
|
* added check for all input parameters - no more HardFaults if setted wrong pin numbers
|
|
* external I2C bus moved out from FlexiPort by Soft_I2C driver so we always has at least 3 UARTs
|
|
* added 1 full-functional UART (only for quads) and 1 RX-only UART for DSM satellite receiver on OpLink connector
|
|
* Unlike many other boards, fully implemented registerPeriodicCallback & Co calls
|
|
* implemented simple preemptive multitasking
|
|
* stack now in CCM memory
|
|
* PPM and PWM inputs works via Timer's driver handlers
|
|
* added DSM and SBUS parsing on PPM input
|
|
* all hardware description tables are now 'const' and locates in flash
|
|
* more reliable reset for I2C bus on hangups
|
|
* all drivers support set_retries()
|
|
* all delays - even microseconds - are very presize by using hardware clock counter (DWT_CYCCNT) in free-running mode
|
|
* separated USB and UART drivers
|
|
* new SoftwareSerial driver based on ST appnote
|
|
* now it uses MPU6000 DRDY output
|
|
* removed all compiler's warnings
|
|
* ported and slightly altered bootloader to support flashing and start firmware automatically at addresses 8010000 and 8020000
|
|
(2 low 16k flash pages are used to emulate EEPROM)
|
|
* EEPROM emulation altered to ensure the reliability of data storage at power failures
|
|
* optimized EEPROM usage by changing from 1-byte to 2-byte writes
|
|
* all internal calls use static private methods
|
|
* removed unused files
|
|
* micros() call uses 32-bit hardware timer instead of awful systick_micros()
|
|
* added parameters support for HAL
|
|
* OneShot supported
|
|
* added translation layer between system PWM modes and borad PWM modes
|
|
* added descriptors for all STM internal hardware
|
|
* added support to reboot to DFU mode (via "reboot to PX4 bootloader" in MP)
|
|
* after any Fault or Panic() automatically reboots to DFU mode
|
|
* diversity on RC_Input
|
|
* unified exception handling
|
|
* added ability to bind Spectrum satellite without managed 3.3 DC-DC (requires short power off)
|
|
* added support for Arduino32 reset sequence - negative DTR edge on 1200 baud or '1eaf' packet with high DTR
|
|
* fixed hang on dataflash malfunction
|
|
* fixed USB characters loss *without* hangup if disconnected
|
|
* added failsafe on receiver's hangup - if no channel changes in 60 seconds
|
|
* changed to simplify support of slightly different boards - eg. AirbotF4
|
|
* full support for AirbotF4 (separate binaries)
|
|
* added support for servos on Input port unused pins
|
|
* Added handling of FLASH_SR error bits, including automatic clearing of write protection
|
|
* added Arduino-like support of relay on arbitrary pin
|
|
* simplified UART driver, buffering now used even in non-blocking mode
|
|
* EEPROM emulation locks flash after each write
|
|
* EEPROM error handling
|
|
* fixed Ardupilot's stealing of Servos even they marked as "Unused"
|
|
* added compilation date & time to log output
|
|
* added SBUS input via any USART with hardware inverter as on Airbot boards
|
|
* added per-board read_me.md files
|
|
* fixed Dataflash logs bug from mainstream - now logs are persists between reboots!
|
|
* DMA mode for lagre SPI transfers
|
|
* USB virtual com-port can be connected to any UART - eg. for OSD or 3DR modems setup
|
|
* any UART can be connected to ESC for 4-way interface
|
|
* support for logs on SD card for AirbotV2 board
|
|
* fixed 2nd Dataflash logs bug from mainstream - now logs are persists between reboots even on boards having chips with 64k sector
|
|
* I2C wait time limited to 30ms - no more forever hangs by external compass errors
|
|
* FlexiPort can be switched between UART and I2C by parameter
|
|
* The RCoutput module has been completely rewritten.
|
|
* For the PWM outputs, the error in setting the timer frequency has been compensated.
|
|
* added parameter to set PWM mode
|
|
* added used memory reporting
|
|
* added I2C error reporting
|
|
* realized low-power idle state with WFE, TIMER6 is used to generate events each 1uS
|
|
* added HAL_RC_INPUT parameter to allow to force RC input mode
|
|
* added used stack reporting
|
|
* added generation of .DFU file
|
|
* time-consuming operations moved out from ISR level to IO_Completion level with low priority
|
|
* added support for Clock Security System - if HSE fails in air system will use HSI instead
|
|
* added boardEmergencyHandler which will be called on any Fault or Panic() before halt - eg. to release parachute
|
|
* motor layout switched to per-board basis
|
|
* console assignment switched to per-board basis
|
|
* HAL switched to new DMA api with completion interrupts
|
|
* AirbotV2 is fully supported with SD card and OSD
|
|
* added support for reading from SD card via USB - HAL parameter allows to be USB MassStorege
|
|
* added check for stack overflow for all tasks
|
|
* all boards formats internal flash chip as FAT and allows access via USB
|
|
* added spi flash autodetection
|
|
* added support for TRIM command on FAT-formatted Dataflash
|
|
* rewritten SD library to support 'errno' and early distinguish between file and dir
|
|
* compass processing (4027uS) and baro processing(1271uS) moved out from interrupt level to task level, because its
|
|
execution time spoils loop time (500Hz = 2000uS for all)
|
|
* added reformatting of DataFlash in case of hard filesystem errors, which fixes FatFs bug when there is no free space
|
|
after file overflows and then deleted
|
|
* added autodetect for all known types of baro on external I2C bus
|
|
* added autodetect for all known types of compass on external I2C bus
|
|
* added check to I2C_Mgr for same device on same bus - to prevent autodetection like MS5611 (already initialized) as BMP_085
|
|
* added time offset HAL parameter
|
|
* added time syncronization between board's time and GPS time - so logs now will show real local date&time
|
|
* i2c driver is fully rewritten, added parsing of bus error flags - ARLO & BERR
|
|
* errors at STOP don't cause data loss or time errors - bus reset scheduled as once io_task
|
|
* added parsing of TIMEOUT bus flag
|
|
* added asyncronous bus reset in case when loockup occures after STOP generation
|
|
* full BusReset changed to SoftReset on 1st try
|
|
* new SoftI2C driver uses timer and works in interrupts
|
|
* added support for SUMD and non-inverted SBUS via PPM pins
|
|
* added support for SUMD via UARTs
|
|
* MPU not uses FIFO - data readed out via interrupts
|
|
* added parametr allowing to defer EEPROM save up to disarm
|
|
* optimized preemptive multitask, which does not context switch if next task is the same as current. Real context switch occures in ~4% of calls to task scheduler
|
|
* all work with task list moved out to ISR level so there is no race condition anymore
|
|
* all work with semaphores moved out to the same ISR level so serialized by hardware and don't requires disabling interrupts
|
|
* added parameter RC_FS to enable all RC failsafe
|
|
* added disabling of data cache on flash write, just for case (upstream has this update too)
|
|
* added a way to schedule context switch from ISR, eg. at data receive or IO_Complete
|
|
* added timeout to SPI flags waiting
|
|
* now task having started any IO (DMA or interrupts) goes to pause and resumes in IO_Completion ISR, not eating CPU time in wait loop
|
|
* optimized I2C wait times to work on noisy lines
|
|
* greatly reduced time of reformatting of DataFlash to FAT
|
|
* I2C driver fully rewritten again to work via interrupts - no DMA, no polling
|
|
* compass and baro gives bus semaphore ASAP to allow bus operations when calculations does
|
|
* full status on only 2 leds - GPS sats count, failsafe, compass calibration, autotune etc
|
|
* support for SBUS on any UART
|
|
* PWM_IN is rewritten to use HAL drivers, as result its size decreased four times (!)
|
|
* working PPM on AirbotV2/V3
|
|
* buzzer support
|
|
* added ability to connect buzzer to arbitrary pin (parameter BUZZ_PIN)
|
|
* added priority to SPI DMA transfers, to prevent such issues - https://github.com/betaflight/betaflight/issues/2631
|
|
* overclocking support
|
|
* OSD is working
|
|
* 'boards' folder moved from 'wirish' to HAL directory, to help to find them
|
|
* added translation of decoded serial data from PPMn input port to fake UARTs
|
|
* reduced to ~1.5uS time from interrupt to resuming task that was waiting that interrupt
|
|
* unified NVIC handling
|
|
* SoftSerial driver rewritten to not use PWM dependency. Now it can use any pin with timer for RX and any pin for TX, and there
|
|
can be any number of SoftSerial UARTs
|
|
* added per-task stack usage
|
|
* SPI driver rewritten: added ISR mode instead of polling, all transfers are monolitic (not divded to send and receive parts), setup for receive now in ISR
|
|
* all DataFlash reads and writes now in single SPI transfer
|
|
* removed usage of one-byte SPI functions from SD driver
|
|
* added support of criticalSections to Scheduler, which protect code from task switch without disabling interrupts
|
|
* added CS assert/release delays to SPI device descriptrion table
|
|
* added partial MPU support (only to protect from process stack overflow)
|
|
* removed -fpermissive from GCC options
|
|
* class SD is slightly redesigned, reducing the memory consumption by half (!)
|
|
* optimized dma_init_transfer() function: now it twice faster and requires 3 times less memory
|
|
* added SD size to bootlog
|
|
* SPI via interrupts now works
|
|
* added pin names to simplify porting of boards
|
|
* added DSM rssi as last channel
|
|
* IO tasks excluded from priority boost on yield()
|
|
* added awakening of main thread after receiving of data from MPU
|
|
* ArduCopter loop at 1KHz! fixed all issues, mean scheduling error is only 10uS - 10 times less than OS tick!
|
|
* narowed type for timer_channel
|
|
* added support for PWM outputs on N-channels of advanced timers
|
|
* added support for inverted buzzer
|
|
* added support for passive buzzer
|
|
* added support for Devo telemetry protocol
|
|
* fixed Soft_I2C timeout
|
|
* all waits for SD answers moved to ISR as finite state machine
|
|
* a try to support Ardupilot parameters on builtin OSD (untested)
|
|
* removed unnecessary diagnostics which cause MAVlink corruption
|
|
* added gyro drift compensation, parameter HAL_CORRECT_GYRO is a integrator time in seconds (30 is a good starting point).
|
|
* added diagnosis of the cause of failsafe triggering
|
|
* Parameter HAL_RC_FS now sets a time of RC failsafe in seconds (60 is a good value for digital protocols)
|
|
* added MAVlink messages about SD card errors
|
|
* renamed board *_MP32V1F4 to *_Revolution to simplify things
|
|
* fixed bug in RC_Input that cause permanent Failsafe
|
|
* added motor clipping reporting and baro compensation by GPS from https://github.com/DuraCopter/ardupilot
|
|
* ...
|
|
* a lot of minor enhancements
|
|
|
|
|
|
|
|
|
|
|