mirror of https://github.com/ArduPilot/ardupilot
110 lines
4.0 KiB
Plaintext
110 lines
4.0 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for The CUBE Black and the Cube Purple hardware
|
|
# this is based on fmuv3, but with vendor specific USB IDs
|
|
|
|
include ../fmuv3/hwdef.dat
|
|
|
|
define HAL_CHIBIOS_ARCH_CUBE 1
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
# USB setup
|
|
USB_VENDOR 0x2DAE # ONLY FOR USE BY HEX! NOBODY ELSE
|
|
USB_PRODUCT 0x1011
|
|
USB_STRING_MANUFACTURER "Hex/ProfiCNC"
|
|
|
|
# remap PB0/1 as ADC's
|
|
undef PB0
|
|
undef PB1
|
|
PB0 PB0_ADC ADC1 SCALE(1)
|
|
PB1 PB1_ADC ADC1 SCALE(1)
|
|
|
|
SPIDEV icm20948_ext SPI4 DEVID1 MPU_EXT_CS MODE3 4*MHZ 8*MHZ
|
|
SPIDEV icm20602_ext SPI4 DEVID3 GYRO_EXT_CS MODE3 4*MHZ 8*MHZ
|
|
|
|
|
|
# Sensor Check alias for validating board type
|
|
CHECK_MPU9250 spi_check_register("mpu9250", MPUREG_WHOAMI, MPU_WHOAMI_MPU9250)
|
|
CHECK_MPU9250_EXT spi_check_register("mpu9250_ext", MPUREG_WHOAMI, MPU_WHOAMI_MPU9250)
|
|
CHECK_ICM20602_EXT spi_check_register("icm20602_ext", MPUREG_WHOAMI, MPU_WHOAMI_ICM20602)
|
|
CHECK_LSM9DS0_EXT_G spi_check_register("lsm9ds0_ext_g", LSMREG_WHOAMI, LSM_WHOAMI_L3GD20)
|
|
CHECK_LSM9DS0_EXT_AM spi_check_register("lsm9ds0_ext_am", LSMREG_WHOAMI, LSM_WHOAMI_LSM303D)
|
|
CHECK_ICM20948_EXT spi_check_register("icm20948_ext", INV2REG_WHOAMI, INV2_WHOAMI_ICM20948)
|
|
CHECK_MS5611 check_ms5611("ms5611")
|
|
CHECK_MS5611_EXT check_ms5611("ms5611_ext")
|
|
|
|
# Sensor Check Macros to be used for validating board type
|
|
CHECK_IMU0_PRESENT $CHECK_MPU9250_EXT || $CHECK_ICM20602_EXT
|
|
CHECK_IMU1_PRESENT ($CHECK_LSM9DS0_EXT_G && $CHECK_LSM9DS0_EXT_AM) || $CHECK_ICM20948_EXT
|
|
CHECK_IMU2_PRESENT $CHECK_MPU9250
|
|
CHECK_BARO0_PRESENT $CHECK_MS5611
|
|
CHECK_BARO1_PRESENT $CHECK_MS5611_EXT
|
|
|
|
BOARD_VALIDATE $CHECK_IMU0_PRESENT $CHECK_IMU1_PRESENT $CHECK_IMU2_PRESENT $CHECK_BARO0_PRESENT $CHECK_BARO1_PRESENT
|
|
|
|
# also define the default board type
|
|
define BOARD_TYPE_DEFAULT 3
|
|
|
|
# three IMUs, but allow for different variants. First two IMUs are
|
|
# isolated, 3rd isn't
|
|
IMU Invensense SPI:mpu9250_ext ROTATION_PITCH_180
|
|
|
|
# the 3 rotations for the LSM9DS0 driver are for the accel, the gyro
|
|
# and the H variant of the gyro
|
|
IMU LSM9DS0 SPI:lsm9ds0_ext_g SPI:lsm9ds0_ext_am ROTATION_ROLL_180_YAW_270 ROTATION_ROLL_180_YAW_90 ROTATION_ROLL_180_YAW_90
|
|
|
|
# 3rd non-isolated IMU
|
|
IMU Invensense SPI:mpu9250 ROTATION_YAW_270
|
|
|
|
# alternative IMU set for newer cubes
|
|
IMU Invensense SPI:icm20602_ext ROTATION_ROLL_180_YAW_270
|
|
IMU Invensensev2 SPI:icm20948_ext ROTATION_PITCH_180
|
|
IMU Invensensev2 SPI:icm20948 ROTATION_YAW_270
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 5
|
|
|
|
# two baros
|
|
BARO MS56XX SPI:ms5611_ext
|
|
BARO MS56XX SPI:ms5611
|
|
|
|
# two compasses. First is in the LSM303D
|
|
COMPASS LSM303D SPI:lsm9ds0_ext_am ROTATION_YAW_270
|
|
# 2nd compass is part of the 2nd invensense IMU
|
|
COMPASS AK8963:probe_mpu9250 1 ROTATION_YAW_270
|
|
|
|
# compass as part of ICM20948 on newer cubes
|
|
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180_YAW_90
|
|
|
|
# also probe for external compasses
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
# This defines an output pin which will default to output HIGH. It is
|
|
# a pin that enables peripheral power on this board. It starts in the
|
|
# off state, then is pulled low to enable peripherals in
|
|
# peripheral_power_enable()
|
|
undef PA8
|
|
PA8 nVDD_5V_PERIPH_EN OUTPUT HIGH
|
|
|
|
# This is the pin to enable the sensors rail. It can be used to power
|
|
# cycle sensors to recover them in case there are problems with power on
|
|
# timing affecting sensor stability. We pull it LOW on startup, which
|
|
# means sensors off, then it is pulled HIGH in peripheral_power_enable()
|
|
undef PE3
|
|
PE3 VDD_3V3_SENSORS_EN OUTPUT LOW
|
|
|
|
# if you want to enable parameter backup/restore then uncomment the following two lines
|
|
# Note: this will use 16k more RAM, so ensure you have enough by looking at MEMINFO messages
|
|
# in MAVLink2 or in PM message in logs
|
|
# undef HAL_STORAGE_SIZE
|
|
# define HAL_STORAGE_SIZE 32768
|
|
|
|
|
|
define HAL_IMU_TEMP_MARGIN_LOW_DEFAULT 5
|
|
|
|
# default the 2nd interface to SLCAN
|
|
define HAL_OTG2_PROTOCOL SerialProtocol_SLCAN
|
|
ROMFS io_firmware_dshot.bin Tools/IO_Firmware/iofirmware_dshot_highpolh.bin
|
|
ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_highpolh.bin
|
|
|
|
# enable support for dshot on iomcu
|
|
define HAL_WITH_IO_MCU_DSHOT 1
|