mirror of https://github.com/ArduPilot/ardupilot
58 lines
2.7 KiB
C
58 lines
2.7 KiB
C
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
// This file is just a placeholder for your configuration file. If you wish to change any of the setup parameters from
|
|
// their default values, place the appropriate #define statements here.
|
|
|
|
// For example if you wanted the Port 3 baud rate to be 38400 you would add a statement like the one below (uncommented)
|
|
//#define SERIAL3_BAUD 38400
|
|
//#define GCS_PROTOCOL GCS_PROTOCOL_NONE
|
|
|
|
|
|
// You may also put an include statement here to point at another configuration file. This is convenient if you maintain
|
|
// different configuration files for different aircraft or HIL simulation. See the examples below
|
|
//#include "APM_Config_mavlink_hil.h"
|
|
//#include "Skywalker.h"
|
|
|
|
// The following are the recommended settings for Xplane simulation. Remove the leading "/* and trailing "*/" to enable:
|
|
|
|
/*
|
|
#define HIL_PROTOCOL HIL_PROTOCOL_MAVLINK
|
|
#define HIL_MODE HIL_MODE_ATTITUDE
|
|
#define HIL_PORT 0
|
|
#define GCS_PROTOCOL GCS_PROTOCOL_MAVLINK
|
|
#define GCS_PORT 3
|
|
*/
|
|
|
|
#define MAGNETOMETER ENABLED
|
|
|
|
// ----- Camera definitions ------
|
|
// ------------------------------
|
|
#define CAMERA ENABLED
|
|
#define CAM_DEBUG DISABLED
|
|
// Comment out servos that you do not have
|
|
//#define CAM_SERVO 8 // Camera servo channel
|
|
#define CAM_ANGLE 30 // Set angle in degrees
|
|
//#define CAM_CLICK 45 // This is the position of the servo arm when it actually clicks
|
|
//#define OPEN_SERVO 5 // Retraction servo channel - my camera retracts yours might not.
|
|
|
|
// Camera yaw (left-right)
|
|
#define YAW_SERVO 7 // Pan servo channel (can be pitch in stabilization)
|
|
#define YAW_REV 1 // output is normal = 1 output is reversed = -1
|
|
#define YAW_CENTER 0 // Camera center bearing with relation to airframe forward motion - deg
|
|
#define YAW_RANGE 90 // Pan Servo sweep in degrees
|
|
#define YAW_RATIO 10.31 // match this to the swing of your pan servo
|
|
|
|
// Camera pitch (up-down)
|
|
#define PITCH_SERVO 6 // Tilt servo channel (can be roll in stabilization)
|
|
#define PITCH_REV 1 // output is normal = 1 output is reversed = -1
|
|
#define PITCH_CENTER 0 // Camera center bearing with relation to airframe forward motion - deg
|
|
#define PITCH_RANGE 90 // Tilt Servo sweep in degrees
|
|
#define PITCH_RATIO 10.31 // match this to the swing of your tilt servo
|
|
|
|
// Camera roll (up-down)
|
|
#define ROLL_SERVO 6 // Tilt servo channel (can be roll in stabilization)
|
|
#define ROLL_REV 1 // output is normal = 1 output is reversed = -1
|
|
#define ROLL_CENTER 0 // Camera center bearing with relation to airframe forward motion - deg
|
|
#define ROLL_RANGE 90 // Tilt Servo sweep in degrees
|
|
#define ROLL_RATIO 10.31 // match this to the swing of your tilt servo
|