mirror of https://github.com/ArduPilot/ardupilot
350 lines
8.2 KiB
Plaintext
350 lines
8.2 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for JAE JFB-100 hardware.(modified based fmuv5)
|
|
|
|
# MCU class and specific type. It is a F765, which is the same as F767
|
|
# but without the TFT interface
|
|
MCU STM32F7xx STM32F767xx
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_FMUV5
|
|
define HAL_CHIBIOS_ARCH_FMUV5 1
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1084
|
|
|
|
FLASH_RESERVE_START_KB 32
|
|
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 USART3 USART1 UART4 USART6 UART7 OTG2
|
|
|
|
# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
|
|
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2
|
|
|
|
# now we define the pins that USB is connected on
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# these are the pins for SWD debugging with a STlinkv2 or black-magic probe
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# SPI1 - internal sensors
|
|
PG11 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PD7 SPI1_MOSI SPI1
|
|
|
|
# SPI2 - FRAM
|
|
PI1 SPI2_SCK SPI2
|
|
PI2 SPI2_MISO SPI2
|
|
PI3 SPI2_MOSI SPI2
|
|
|
|
# SPI4 - sensors2
|
|
PE2 SPI4_SCK SPI4
|
|
PE13 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
# SPI5 - external1 (disabled to save DMA channels)
|
|
# PF7 SPI5_SCK SPI5
|
|
# PF8 SPI5_MISO SPI5
|
|
# PF9 SPI5_MOSI SPI5
|
|
|
|
# SPI6 - external2 (disabled to save DMA channels)
|
|
# PG13 SPI6_SCK SPI6
|
|
# PG12 SPI6_MISO SPI6
|
|
# PB5 SPI6_MOSI SPI6
|
|
|
|
# sensor CS
|
|
PF10 MS5611_CS CS
|
|
PF2 SCHA63T_G_CS CS
|
|
PF3 ICM20602_CS CS SPEED_VERYLOW
|
|
PF4 SCHA63T_A_CS CS
|
|
PF5 FRAM_CS CS SPEED_VERYLOW
|
|
|
|
# unusued CS pins
|
|
# PF11 SPARE_CS CS (using for WA6)
|
|
PH5 AUXMEM_CS CS
|
|
PI4 EXTERNAL1_CS1 CS
|
|
PI10 EXTERNAL1_CS2 CS
|
|
PI11 EXTERNAL1_CS3 CS
|
|
PI6 EXTERNAL2_CS1 CS
|
|
PI7 EXTERNAL2_CS2 CS
|
|
PI8 EXTERNAL2_CS3 CS
|
|
|
|
# I2C buses
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
PF1 I2C2_SCL I2C2
|
|
PF0 I2C2_SDA I2C2
|
|
|
|
PH7 I2C3_SCL I2C3
|
|
PH8 I2C3_SDA I2C3
|
|
|
|
PF14 I2C4_SCL I2C4
|
|
PF15 I2C4_SDA I2C4
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C3 I2C1 I2C2 I2C4
|
|
|
|
|
|
# enable pins
|
|
PE3 VDD_3V3_SENSORS_EN OUTPUT HIGH
|
|
|
|
# start peripheral power off, then enable after init
|
|
# this prevents a problem with radios that use RTS for
|
|
# bootloader hold
|
|
PF12 nVDD_5V_HIPOWER_EN OUTPUT HIGH
|
|
PG4 nVDD_5V_PERIPH_EN OUTPUT HIGH
|
|
|
|
PG5 VDD_5V_RC_EN OUTPUT HIGH
|
|
PG6 VDD_5V_WIFI_EN OUTPUT HIGH
|
|
PG7 VDD_3V3_SD_CARD_EN OUTPUT HIGH
|
|
|
|
# drdy pins
|
|
# PE7 DRDY8_NC INPUT (using for WA5)
|
|
PB4 DRDY1_ICM20689 INPUT
|
|
PB14 DRDY2_SCHA63T_GYRO INPUT
|
|
PB15 DRDY3_SCHA63T_ACC INPUT
|
|
PC5 DRDY4_ICM20602 INPUT
|
|
PC13 DRDY5_SCHA63T_GYRO INPUT
|
|
PD10 DRDY6_SCHA63T_ACC INPUT
|
|
PD15 DRDY7_EXTERNAL1 INPUT
|
|
|
|
# Control of Spektrum power pin
|
|
PE4 SPEKTRUM_PWR OUTPUT HIGH GPIO(73)
|
|
define HAL_GPIO_SPEKTRUM_PWR 73
|
|
|
|
# Spektrum Power is Active High
|
|
define HAL_SPEKTRUM_PWR_ENABLED 1
|
|
|
|
# UARTs
|
|
|
|
# USART2 is telem1
|
|
PD6 USART2_RX USART2
|
|
PD5 USART2_TX USART2
|
|
PD3 USART2_CTS USART2
|
|
PD4 USART2_RTS USART2
|
|
|
|
# USART1 is GPS1
|
|
PB7 USART1_RX USART1 NODMA
|
|
PB6 USART1_TX USART1 NODMA
|
|
|
|
# USART3 is telem2
|
|
PD9 USART3_RX USART3
|
|
PD8 USART3_TX USART3
|
|
PD11 USART3_CTS USART3
|
|
PD12 USART3_RTS USART3
|
|
|
|
# UART4 GPS2
|
|
PD0 UART4_RX UART4 NODMA
|
|
PD1 UART4_TX UART4 NODMA
|
|
|
|
# USART6 is telem3
|
|
PG9 USART6_RX USART6 NODMA
|
|
# we leave PG14 as an input to prevent it acting as a pullup
|
|
# on the IOMCU SBUS input
|
|
PG14 USART6_TX USART6 NODMA
|
|
# PG15 USART6_CTS USART6 (using for WA8)
|
|
# PG8 USART6_RTS USART6 (using for WA7)
|
|
|
|
# UART7 is debug
|
|
PF6 UART7_RX UART7 NODMA
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
# UART8 is for IOMCU
|
|
# PE0 UART8_RX UART8 (using for PP3)
|
|
# PE1 UART8_TX UART8 (using for PP5)
|
|
|
|
# UART for IOMCU
|
|
# IOMCU_UART UART8
|
|
|
|
# RCInput on the PPM pin, for all protocols
|
|
PI5 TIM8_CH1 TIM8 RCININT PULLUP LOW
|
|
|
|
# PWM AUX channels
|
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
|
PA10 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
# we need to disable DMA on the last 2 FMU channels
|
|
# as timer 12 doesn't have a TIMn_UP DMA option
|
|
PH6 TIM12_CH1 TIM12 PWM(7) GPIO(56) NODMA
|
|
PH9 TIM12_CH2 TIM12 PWM(8) GPIO(57) NODMA
|
|
|
|
define BOARD_PWM_COUNT_DEFAULT 8
|
|
|
|
# PWM output for buzzer
|
|
PE5 TIM9_CH1 TIM9 GPIO(77) ALARM
|
|
|
|
# analog in
|
|
PA0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
PA2 BATT2_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA3 BATT2_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
PC4 SPARE1_ADC1 ADC1 SCALE(1)
|
|
PA4 SPARE2_ADC1 ADC1 SCALE(1)
|
|
|
|
PB0 RSSI_IN ADC1 SCALE(1)
|
|
|
|
PC3 HW_REV_SENS ADC1 SCALE(1)
|
|
PC2 HW_VER_SENS ADC1 SCALE(1)
|
|
|
|
PC0 VDD_5V_SENS ADC1 SCALE(2)
|
|
PC1 SCALED_V3V3 ADC1 SCALE(2)
|
|
|
|
# setup scaling defaults for PixHackV5 power brick
|
|
# define HAL_BATT_VOLT_SCALE 18.0
|
|
# define HAL_BATT_CURR_SCALE 24.0
|
|
# setup for supplied power brick
|
|
define HAL_BATT_VOLT_SCALE 18.182
|
|
define HAL_BATT_CURR_SCALE 36.364
|
|
define HAL_BATT_VOLT_PIN 0
|
|
define HAL_BATT_CURR_PIN 1
|
|
define HAL_BATT2_VOLT_PIN 2
|
|
define HAL_BATT2_CURR_PIN 3
|
|
|
|
# CAN bus
|
|
PI9 CAN1_RX CAN1
|
|
PH13 CAN1_TX CAN1
|
|
|
|
PB12 CAN2_RX CAN2
|
|
PB13 CAN2_TX CAN2
|
|
|
|
PH2 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(70)
|
|
PH3 GPIO_CAN2_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(71)
|
|
PH4 GPIO_CAN3_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(72)
|
|
|
|
# GPIOs
|
|
PA7 HEATER_EN OUTPUT LOW GPIO(80)
|
|
define HAL_HEATER_GPIO_PIN 80
|
|
|
|
PG1 VDD_BRICK_nVALID INPUT PULLUP
|
|
PG2 VDD_BRICK2_nVALID INPUT PULLUP
|
|
PG3 VBUS_nVALID INPUT PULLUP
|
|
PF13 VDD_5V_HIPOWER_nOC INPUT PULLUP
|
|
PE15 VDD_5V_PERIPH_nOC INPUT PULLUP
|
|
# PB10 nSPI5_RESET_EXTERNAL1 OUTPUT HIGH (using for WA4)
|
|
|
|
# capture pins
|
|
PA5 FMU_CAP1 INPUT GPIO(58)
|
|
PB3 FMU_CAP2 INPUT GPIO(59)
|
|
PB11 FMU_CAP3 INPUT GPIO(60)
|
|
PI0 FMU_SPARE_4 INPUT GPIO(61)
|
|
|
|
# SPI devices
|
|
SPIDEV ms5611 SPI4 DEVID1 MS5611_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV scha63t_g SPI1 DEVID1 SCHA63T_G_CS MODE0 10*MHZ 10*MHZ
|
|
SPIDEV scha63t_a SPI1 DEVID2 SCHA63T_A_CS MODE0 10*MHZ 10*MHZ
|
|
SPIDEV icm20602 SPI1 DEVID3 ICM20602_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV ramtron SPI2 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
|
|
# up to 3 IMUs
|
|
IMU SCHA63T SPI:scha63t_a SPI:scha63t_g ROTATION_NONE
|
|
IMU Invensense SPI:icm20602 ROTATION_PITCH_180_YAW_270
|
|
|
|
# 3rd could be BMMI055 or BMI088
|
|
# IMU BMI055 SPI:bmi055_a SPI:bmi055_g ROTATION_ROLL_180_YAW_90
|
|
# IMU BMI088 SPI:bmi055_a SPI:bmi055_g ROTATION_ROLL_180_YAW_90
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
|
|
|
# probe external I2C compasses plus some internal IST8310
|
|
# we also probe some external IST8310 with a non-standard orientation
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
COMPASS IST8310 I2C:ALL_EXTERNAL:0x0E true ROTATION_ROLL_180_YAW_90
|
|
COMPASS IST8310 I2C:ALL_INTERNAL:0x0E false ROTATION_YAW_270
|
|
|
|
# one baro
|
|
BARO MS56XX SPI:ms5611
|
|
|
|
# microSD support
|
|
PC8 SDMMC_D0 SDMMC1
|
|
PC9 SDMMC_D1 SDMMC1
|
|
PC10 SDMMC_D2 SDMMC1
|
|
PC11 SDMMC_D3 SDMMC1
|
|
PC12 SDMMC_CK SDMMC1
|
|
PD2 SDMMC_CMD SDMMC1
|
|
|
|
# red LED marked as B/E
|
|
# PB1 LED_RED OUTPUT OPENDRAIN GPIO(90) (swap)
|
|
|
|
# green LED marked as PWR. We leave this solid on, but allow
|
|
# for it to be controlled as a relay if needed
|
|
PC6 LED_GREEN OUTPUT GPIO(91) LOW
|
|
|
|
# blue LED marked as ACT
|
|
PC7 LED_BLUE OUTPUT GPIO(90) HIGH
|
|
# red LED marked as B/E
|
|
PB1 LED_RED OUTPUT OPENDRAIN GPIO(92)
|
|
|
|
# setup for BoardLED2
|
|
define HAL_GPIO_A_LED_PIN 90
|
|
define HAL_GPIO_B_LED_PIN 92
|
|
define HAL_GPIO_LED_ON 0
|
|
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_STORAGE_SIZE 32768
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# allow to have have a dedicated safety switch pin
|
|
define HAL_HAVE_SAFETY_SWITCH 1
|
|
|
|
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
DMA_PRIORITY SDMMC* UART8* ADC* SPI* TIM*
|
|
|
|
# define HAL_SPI_CHECK_CLOCK_FREQ 1
|
|
|
|
# enable FAT filesystem support (needs a microSD defined via SDMMC)
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
# uncomment block below to enable a 2nd MS5611 baro on SPI5
|
|
#PF7 SPI5_SCK SPI5
|
|
#PF8 SPI5_MISO SPI5
|
|
#PF9 SPI5_MOSI SPI5
|
|
#SPIDEV ms5611_spi5 SPI5 DEVID1 EXTERNAL1_CS1 MODE3 20*MHZ 20*MHZ
|
|
#undef PI10
|
|
#PI10 EXTERNAL1_CS2 OUTPUT LOW
|
|
#BARO MS56XX SPI:ms5611_spi5
|
|
|
|
# imu sensor SCHA63T reset
|
|
PH12 SCHA63T_RESET OUTPUT LOW
|
|
|
|
# PWM wraparound 1-8
|
|
PA8 WA1 INPUT PULLUP
|
|
PA15 WA2 INPUT PULLUP
|
|
PB2 WA3 INPUT PULLUP
|
|
PB10 WA4 INPUT PULLUP
|
|
PE7 WA5 INPUT PULLUP
|
|
PF11 WA6 INPUT PULLUP
|
|
PG8 WA7 INPUT PULLUP
|
|
PG15 WA8 INPUT PULLUP
|
|
|
|
# now we define the pins that USB is connected on
|
|
PA9 VBAS INPUT PULLDOWN
|
|
|
|
# External watchdog gpio
|
|
PH11 EXT_WDOG OUTPUT SPEED_VERYLOW
|
|
define EXT_WDOG_INTERVAL_MS 50
|
|
|
|
# safety switch
|
|
PE10 SAFETY_IN INPUT PULLUP
|