ardupilot/libraries/AP_HAL_ChibiOS/hwdef/speedybeef4v3
Peter Barker 956ac243e1 AP_HAL_ChibiOS: adjust hwdef files for define renames 2024-07-11 09:34:00 +10:00
..
README.md
SpeedyBee_F405_v3_Board_Bottom.JPG
SpeedyBee_F405_v3_Board_Top.JPG
defaults.parm AP_HAL_ChibiOS: move NTF_LED_TYPES from defaults to hwdef 2023-05-04 07:45:12 +10:00
hwdef-bl.dat hwdef: don't use DEFAULTGPIO in bootloaders 2024-06-25 12:05:40 +10:00
hwdef.dat AP_HAL_ChibiOS: adjust hwdef files for define renames 2024-07-11 09:34:00 +10:00

README.md

SpeedyBee F405 v3 Flight Controller

The SpeedyBee F405 v3 is a flight controller produced by SpeedyBee.

Features

  • STM32F405 microcontroller
  • BMI270 IMU
  • DPS280 barometer
  • SDCard
  • AT7456E OSD
  • 6 UARTs
  • 9 PWM outputs

Pinout

SpeedyBee F405 v3 SpeedyBee F405 v3

UART Mapping

The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.

  • SERIAL0 -> USB
  • SERIAL1 -> UART1 (DJI-VTX, DMA-enabled)
  • SERIAL2 -> UART2 (RCIN, DMA-enabled)
  • SERIAL3 -> UART3 (CAM)
  • SERIAL4 -> UART4 (connected to internal BT module, not currently usable by ArduPilot)
  • SERIAL5 -> UART5 (ESC Telemetry)
  • SERIAL6 -> UART6 (GPS, DMA-enabled)

RC Input

RC input is configured on the R2 (UART2_RX) pin for most RC unidirectional protocols except SBUS which should be applied at the SBUS pin. PPM is not supported. For Fport, a bi-directional inverter will be required. See https://ardupilot.org/plane/docs/common-connecting-sport-fport.html For CRSF/ELRS/SRXL2 connection of the receiver to T2 will also be required.

FrSky Telemetry

FrSky Telemetry is supported using the Tx pin of any UART including SERIAL2/UART2. You need to set the following parameters to enable support for FrSky S.PORT (example shows SERIAL3).

  • SERIAL3_PROTOCOL 10
  • SERIAL3_OPTIONS 7

OSD Support

The SpeedyBee F405 v3 supports OSD using OSD_TYPE 1 (MAX7456 driver).

VTX Support

The JST-GH-6P connector supports a standard DJI HD VTX connection. Pin 1 of the connector is 9v so be careful not to connect this to a peripheral requiring 5v.

PWM Output

The SpeedyBee F405 v3 supports up to 9 PWM outputs. The pads for motor output M1 to M4 on the motor connector, plus M9 for LED strip or another PWM output.

The PWM is in 3 groups:

  • PWM 1-4 in group1
  • PWM 5-8 in group2
  • PWM 9 in group3

Channels within the same group need to use the same output rate. If any channel in a group uses DShot then all channels in the group need to use DShot. Channels 1-4 support bi-directional DShot.

Battery Monitoring

The board has a internal voltage sensor and connections on the ESC connector for an external current sensor input. The voltage sensor can handle up to 6S. LiPo batteries.

The default battery parameters are:

  • BATT_MONITOR 4
  • BATT_VOLT_PIN 10
  • BATT_CURR_PIN 11
  • BATT_VOLT_MULT 11.2
  • BATT_AMP_PERVLT 52.7 (will need to be adjusted for whichever current sensor is attached)

Compass

The SpeedyBee F405 v3 does not have a builtin compass, but you can attach an external compass using I2C on the SDA and SCL pads.

Loading Firmware

Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.

Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Updates should be done with the *.apj firmware files.