mirror of https://github.com/ArduPilot/ardupilot
104 lines
3.6 KiB
C++
104 lines
3.6 KiB
C++
#include "Copter.h"
|
|
|
|
|
|
/*
|
|
* Init and run calls for althold, flight mode
|
|
*/
|
|
|
|
// althold_init - initialise althold controller
|
|
bool ModeAltHold::init(bool ignore_checks)
|
|
{
|
|
|
|
// initialise the vertical position controller
|
|
if (!pos_control->is_active_z()) {
|
|
pos_control->init_z_controller();
|
|
}
|
|
|
|
// set vertical speed and acceleration limits
|
|
pos_control->set_max_speed_accel_z(-get_pilot_speed_dn(), g.pilot_speed_up, g.pilot_accel_z);
|
|
pos_control->set_correction_speed_accel_z(-get_pilot_speed_dn(), g.pilot_speed_up, g.pilot_accel_z);
|
|
|
|
return true;
|
|
}
|
|
|
|
// althold_run - runs the althold controller
|
|
// should be called at 100hz or more
|
|
void ModeAltHold::run()
|
|
{
|
|
// set vertical speed and acceleration limits
|
|
pos_control->set_max_speed_accel_z(-get_pilot_speed_dn(), g.pilot_speed_up, g.pilot_accel_z);
|
|
|
|
// apply SIMPLE mode transform to pilot inputs
|
|
update_simple_mode();
|
|
|
|
// get pilot desired lean angles
|
|
float target_roll, target_pitch;
|
|
get_pilot_desired_lean_angles(target_roll, target_pitch, copter.aparm.angle_max, attitude_control->get_althold_lean_angle_max_cd());
|
|
|
|
// get pilot's desired yaw rate
|
|
float target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->get_control_in());
|
|
|
|
// get pilot desired climb rate
|
|
float target_climb_rate = get_pilot_desired_climb_rate(channel_throttle->get_control_in());
|
|
target_climb_rate = constrain_float(target_climb_rate, -get_pilot_speed_dn(), g.pilot_speed_up);
|
|
|
|
// Alt Hold State Machine Determination
|
|
AltHoldModeState althold_state = get_alt_hold_state(target_climb_rate);
|
|
|
|
// Alt Hold State Machine
|
|
switch (althold_state) {
|
|
|
|
case AltHold_MotorStopped:
|
|
attitude_control->reset_rate_controller_I_terms();
|
|
attitude_control->reset_yaw_target_and_rate(false);
|
|
pos_control->relax_z_controller(0.0f); // forces throttle output to decay to zero
|
|
break;
|
|
|
|
case AltHold_Landed_Ground_Idle:
|
|
attitude_control->reset_yaw_target_and_rate();
|
|
FALLTHROUGH;
|
|
|
|
case AltHold_Landed_Pre_Takeoff:
|
|
attitude_control->reset_rate_controller_I_terms_smoothly();
|
|
pos_control->relax_z_controller(0.0f); // forces throttle output to decay to zero
|
|
break;
|
|
|
|
case AltHold_Takeoff:
|
|
// initiate take-off
|
|
if (!takeoff.running()) {
|
|
takeoff.start(constrain_float(g.pilot_takeoff_alt,0.0f,1000.0f));
|
|
}
|
|
|
|
// get avoidance adjusted climb rate
|
|
target_climb_rate = get_avoidance_adjusted_climbrate(target_climb_rate);
|
|
|
|
// set position controller targets adjusted for pilot input
|
|
takeoff.do_pilot_takeoff(target_climb_rate);
|
|
break;
|
|
|
|
case AltHold_Flying:
|
|
motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);
|
|
|
|
#if AC_AVOID_ENABLED == ENABLED
|
|
// apply avoidance
|
|
copter.avoid.adjust_roll_pitch(target_roll, target_pitch, copter.aparm.angle_max);
|
|
#endif
|
|
|
|
// get avoidance adjusted climb rate
|
|
target_climb_rate = get_avoidance_adjusted_climbrate(target_climb_rate);
|
|
|
|
// update the vertical offset based on the surface measurement
|
|
copter.surface_tracking.update_surface_offset();
|
|
|
|
// Send the commanded climb rate to the position controller
|
|
pos_control->set_pos_target_z_from_climb_rate_cm(target_climb_rate);
|
|
break;
|
|
}
|
|
|
|
// call attitude controller
|
|
attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(target_roll, target_pitch, target_yaw_rate);
|
|
|
|
// run the vertical position controller and set output throttle
|
|
pos_control->update_z_controller();
|
|
}
|