mirror of https://github.com/ArduPilot/ardupilot
262 lines
5.6 KiB
Plaintext
262 lines
5.6 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for the HolybroV6C hardware
|
|
|
|
|
|
# default to all pins low to avoid ESD issues
|
|
#DEFAULTGPIO OUTPUT LOW PULLDOWN
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 2
|
|
|
|
# USB setup
|
|
USB_VENDOR 0x3162 # ONLY FOR USE BY Holybro
|
|
USB_PRODUCT 0x0053
|
|
USB_STRING_MANUFACTURER "Holybro"
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 56
|
|
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
# to be compatible with the px4 bootloader we need
|
|
# to use a different RAM_MAP
|
|
env USE_ALT_RAM_MAP 1
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 UART7 UART5 USART1 UART8 USART2 USART3 OTG2
|
|
|
|
# USB
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
PA9 VBUS INPUT OPENDRAIN
|
|
|
|
# pins for SWD debugging
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# telem1
|
|
PE8 UART7_TX UART7
|
|
PE7 UART7_RX UART7
|
|
PE9 UART7_RTS UART7 LOW PULLDOWN
|
|
PE10 UART7_CTS UART7
|
|
|
|
# telem2
|
|
PC12 UART5_TX UART5
|
|
PD2 UART5_RX UART5
|
|
PC8 UART5_RTS UART5 LOW PULLDOWN
|
|
PC9 UART5_CTS UART5
|
|
|
|
# GPS1
|
|
PB6 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
|
|
# GPS2
|
|
PE1 UART8_TX UART8
|
|
PE0 UART8_RX UART8
|
|
|
|
# uart2 telem3
|
|
PD5 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
|
|
# debug uart
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
|
|
# USART6 is for IOMCU
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
|
|
IOMCU_UART USART6
|
|
|
|
# ADC
|
|
|
|
PC5 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC4 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
PB1 BATT2_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA2 BATT2_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
define HAL_BATT_VOLT_PIN 8
|
|
define HAL_BATT_CURR_PIN 4
|
|
define HAL_BATT_VOLT_SCALE 18.18
|
|
define HAL_BATT_CURR_SCALE 36.36
|
|
|
|
PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
|
|
# SPI1 - IMUs
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
PC13 ICM42688_CS CS
|
|
PC14 BMI055_G_CS CS
|
|
PC15 BMI055_A_CS CS
|
|
PE4 BMI055_DRDY_A INPUT
|
|
PE5 BMI055_DRDY_G INPUT
|
|
PE6 ICM42688_DRDY INPUT
|
|
|
|
# SPI2 - FRAM
|
|
PD3 SPI2_SCK SPI2
|
|
PC2 SPI2_MISO SPI2
|
|
PC3 SPI2_MOSI SPI2
|
|
PD4 FRAM_CS CS
|
|
|
|
# PWM output pins
|
|
PA8 TIM1_CH1 TIM1 PWM(1) GPIO(50)
|
|
PE11 TIM1_CH2 TIM1 PWM(2) GPIO(51)
|
|
PE13 TIM1_CH3 TIM1 PWM(3) GPIO(52)
|
|
PE14 TIM1_CH4 TIM1 PWM(4) GPIO(53)
|
|
PD14 TIM4_CH3 TIM4 PWM(5) GPIO(54)
|
|
PD15 TIM4_CH4 TIM4 PWM(6) GPIO(55)
|
|
PA0 TIM5_CH1 TIM5 PWM(7) GPIO(56)
|
|
PA1 TIM5_CH2 TIM5 PWM(8) GPIO(57)
|
|
|
|
# CAN bus
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
|
|
PB5 CAN2_RX CAN2
|
|
PB13 CAN2_TX CAN2
|
|
|
|
|
|
# I2C buses
|
|
|
|
# I2C1, GPS+MAG
|
|
PB7 I2C1_SDA I2C1
|
|
PB8 I2C1_SCL I2C1
|
|
|
|
# I2C2, GPS2+MAG
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
# I2C4 internal
|
|
PD12 I2C4_SCL I2C4
|
|
PD13 I2C4_SDA I2C4
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C4 I2C1 I2C2
|
|
define HAL_I2C_INTERNAL_MASK 1
|
|
|
|
# this board is tight on DMA channels. To allow for more UART DMA we
|
|
# disable DMA on I2C. This also prevents a problem with DMA on I2C
|
|
# interfering with IMUs
|
|
|
|
# heater
|
|
PB9 HEATER_EN OUTPUT LOW GPIO(80)
|
|
define HAL_HEATER_GPIO_PIN 80
|
|
|
|
# Setup the IMU heater
|
|
define HAL_HAVE_IMU_HEATER 1
|
|
define HAL_IMU_TEMP_DEFAULT 45
|
|
define HAL_IMUHEAT_P_DEFAULT 50
|
|
define HAL_IMUHEAT_I_DEFAULT 0.07
|
|
|
|
# power enable pins
|
|
PB2 VDD_3V3_SENSORS1_EN OUTPUT HIGH
|
|
|
|
# start peripheral power on
|
|
PC10 nVDD_5V_HIPOWER_EN OUTPUT LOW
|
|
PE2 nVDD_5V_PERIPH_EN OUTPUT LOW
|
|
|
|
# Control of Spektrum power pin
|
|
PH2 SPEKTRUM_PWR OUTPUT HIGH GPIO(73)
|
|
define HAL_GPIO_SPEKTRUM_PWR 73
|
|
|
|
# Spektrum Power is Active High
|
|
define HAL_SPEKTRUM_PWR_ENABLED 1
|
|
|
|
# power sensing
|
|
PE3 VDD_5V_PERIPH_nOC INPUT PULLUP
|
|
PC11 VDD_5V_HIPOWER_nOC INPUT PULLUP
|
|
|
|
PA15 VDD_BRICK_nVALID INPUT PULLUP
|
|
PB12 VDD_BRICK2_nVALID INPUT PULLUP
|
|
|
|
# microSD support
|
|
PD6 SDMMC2_CK SDMMC2
|
|
PD7 SDMMC2_CMD SDMMC2
|
|
PB14 SDMMC2_D0 SDMMC2
|
|
PB15 SDMMC2_D1 SDMMC2
|
|
PB3 SDMMC2_D2 SDMMC2
|
|
PB4 SDMMC2_D3 SDMMC2
|
|
define FATFS_HAL_DEVICE SDCD2
|
|
|
|
# LEDs
|
|
PD10 LED_RED OUTPUT OPENDRAIN GPIO(90) HIGH
|
|
PD11 LED_BLUE OUTPUT OPENDRAIN GPIO(92) HIGH
|
|
|
|
# setup for BoardLED2
|
|
define HAL_GPIO_A_LED_PIN 90
|
|
define HAL_GPIO_B_LED_PIN 92
|
|
define HAL_GPIO_LED_ON 0
|
|
|
|
# ID pins
|
|
PE12 HW_VER_REV_DRIVE OUTPUT LOW
|
|
# PC0 HW_REV_SENS ADC1 SCALE(1)
|
|
# PC1 HW_VER_SENS ADC1 SCALE(1)
|
|
|
|
# PWM output for buzzer
|
|
PB0 TIM3_CH3 TIM3 GPIO(77) ALARM
|
|
|
|
# barometers
|
|
BARO MS56XX I2C:0:0x76
|
|
BARO MS56XX I2C:0:0x77
|
|
BARO BMP388 I2C:0:0x77
|
|
|
|
# prototypes may have no baro
|
|
define HAL_BARO_ALLOW_INIT_NO_BARO 1
|
|
|
|
# compass
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
COMPASS IST8310 I2C:0:0x0C false ROTATION_NONE
|
|
|
|
# compensate for magnetic field generated by the heater on 6C IST8310
|
|
define HAL_HEATER_MAG_OFFSET {AP_HAL::Device::make_bus_id(AP_HAL::Device::BUS_TYPE_I2C,0,0xc,0xa),Vector3f(17,14,0)}
|
|
|
|
|
|
# we need to stop the probe of an IST8310 as an internal compass with PITCH_180
|
|
define HAL_COMPASS_DISABLE_IST8310_INTERNAL_PROBE
|
|
|
|
|
|
# SPI devices
|
|
SPIDEV bmi055_g SPI1 DEVID1 BMI055_G_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi055_a SPI1 DEVID2 BMI055_A_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV icm42688 SPI1 DEVID3 ICM42688_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV ramtron SPI2 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
|
|
# 2 IMUs
|
|
IMU Invensensev3 SPI:icm42688 ROTATION_PITCH_180_YAW_90
|
|
IMU BMI055 SPI:bmi055_a SPI:bmi055_g ROTATION_PITCH_180
|
|
# BMI055 is replaced by BMI088 on the lastest hardware revision
|
|
# They use the same CPU signal pins
|
|
IMU BMI088 SPI:bmi055_a SPI:bmi055_g ROTATION_PITCH_180
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 3
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_STORAGE_SIZE 32768
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# allow to have have a dedicated safety switch pin
|
|
define HAL_HAVE_SAFETY_SWITCH 1
|
|
|
|
DMA_PRIORITY SDMMC* USART6* ADC* UART* USART* SPI* TIM*
|
|
|
|
# enable FAT filesystem support (needs a microSD defined via SDMMC)
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_f103_lowpolh.bin
|
|
# enable support for dshot on iomcu
|
|
ROMFS io_firmware_dshot.bin Tools/IO_Firmware/iofirmware_f103_dshot_lowpolh.bin
|
|
define HAL_WITH_IO_MCU_BIDIR_DSHOT 1
|