mirror of https://github.com/ArduPilot/ardupilot
508 lines
16 KiB
C++
508 lines
16 KiB
C++
/*
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#include "AP_RangeFinder_LightWareI2C.h"
|
|
|
|
#if AP_RANGEFINDER_LWI2C_ENABLED
|
|
|
|
#include <AP_HAL/AP_HAL.h>
|
|
#include <AP_HAL/utility/sparse-endian.h>
|
|
|
|
extern const AP_HAL::HAL& hal;
|
|
|
|
#define LIGHTWARE_DISTANCE_READ_REG 0
|
|
#define LIGHTWARE_LOST_SIGNAL_TIMEOUT_READ_REG 22
|
|
#define LIGHTWARE_LOST_SIGNAL_TIMEOUT_WRITE_REG 23
|
|
#define LIGHTWARE_TIMEOUT_REG_DESIRED_VALUE 20 // number of lost signal confirmations for legacy protocol only
|
|
|
|
#define LIGHTWARE_OUT_OF_RANGE_ADD_CM 100
|
|
|
|
static const size_t lx20_max_reply_len_bytes = 32;
|
|
static const size_t lx20_max_expected_stream_reply_len_bytes = 14;
|
|
|
|
#define stream_the_median_distance_to_the_first_return "ldf,0"
|
|
#define stream_the_raw_distance_to_the_first_return "ldf,1"
|
|
#define stream_the_signal_strength_first_return "lhf"
|
|
#define stream_the_raw_distance_to_the_last_return "ldl,1"
|
|
#define stream_the_signal_strength_last_return "lhl"
|
|
#define stream_the_level_of_background_noise "ln"
|
|
|
|
/* Data streams from the LiDAR can include any sf20 LiDAR measurement.
|
|
* A request to stream the desired measurement is made on a 20Hz basis and
|
|
* on the next 20Hz service 50ms later, the result is read and a streaming
|
|
* request is made for the next desired measurement in the sequence.
|
|
* Results are generally available from the LiDAR within 10mS of request.
|
|
*/
|
|
#define STREAM1_VAL stream_the_raw_distance_to_the_last_return
|
|
#define STREAM2_VAL stream_the_signal_strength_last_return
|
|
#define STREAM3_VAL stream_the_raw_distance_to_the_first_return
|
|
#define STREAM4_VAL stream_the_signal_strength_first_return
|
|
#define STREAM5_VAL stream_the_level_of_background_noise
|
|
static const char *parse_stream_id[NUM_SF20_DATA_STREAMS] = { // List of stream identifier strings. Must match init_stream_id[].
|
|
STREAM1_VAL ":"
|
|
};
|
|
|
|
static const char *init_stream_id[NUM_SF20_DATA_STREAMS] = {// List of stream initialization strings. Must match parse_stream_id[].
|
|
"$1" STREAM1_VAL "\r\n"
|
|
};
|
|
|
|
static const uint8_t streamSequence[] = { 0 }; // List of 0 based stream Ids that determine the LiDAR values collected.
|
|
|
|
static const uint8_t numStreamSequenceIndexes = sizeof(streamSequence)/sizeof(streamSequence[0]);
|
|
|
|
AP_RangeFinder_LightWareI2C::AP_RangeFinder_LightWareI2C(RangeFinder::RangeFinder_State &_state,
|
|
AP_RangeFinder_Params &_params,
|
|
AP_HAL::OwnPtr<AP_HAL::I2CDevice> dev)
|
|
: AP_RangeFinder_Backend(_state, _params)
|
|
, _dev(std::move(dev)) {}
|
|
|
|
/*
|
|
Detects if a Lightware rangefinder is connected. We'll detect by
|
|
trying to take a reading on I2C. If we get a result the sensor is
|
|
there.
|
|
*/
|
|
AP_RangeFinder_Backend *AP_RangeFinder_LightWareI2C::detect(RangeFinder::RangeFinder_State &_state,
|
|
AP_RangeFinder_Params &_params,
|
|
AP_HAL::OwnPtr<AP_HAL::I2CDevice> dev)
|
|
{
|
|
if (!dev) {
|
|
return nullptr;
|
|
}
|
|
|
|
AP_RangeFinder_LightWareI2C *sensor
|
|
= NEW_NOTHROW AP_RangeFinder_LightWareI2C(_state, _params, std::move(dev));
|
|
|
|
if (!sensor) {
|
|
return nullptr;
|
|
}
|
|
|
|
WITH_SEMAPHORE(sensor->_dev->get_semaphore());
|
|
if (!sensor->init()) {
|
|
delete sensor;
|
|
return nullptr;
|
|
}
|
|
return sensor;
|
|
}
|
|
|
|
/**
|
|
* Wrapper function over #transfer() to write a sequence of bytes to
|
|
* device. No values are read.
|
|
*/
|
|
bool AP_RangeFinder_LightWareI2C::write_bytes(uint8_t *write_buf_u8, uint32_t len_u8)
|
|
{
|
|
return _dev->transfer(write_buf_u8, len_u8, NULL, 0);
|
|
}
|
|
|
|
/**
|
|
* Disables "address tagging" in the sf20 response packets.
|
|
*/
|
|
void AP_RangeFinder_LightWareI2C::sf20_disable_address_tagging()
|
|
{
|
|
sf20_send_and_expect("#CT,0\r\n", "ct:0");
|
|
}
|
|
|
|
/*
|
|
send a native command and check for an expected reply
|
|
*/
|
|
bool AP_RangeFinder_LightWareI2C::sf20_send_and_expect(const char* send_msg, const char* expected_reply)
|
|
{
|
|
const size_t expected_reply_len = strlen(expected_reply);
|
|
uint8_t rx_bytes[expected_reply_len + 1];
|
|
memset(rx_bytes, 0, sizeof(rx_bytes));
|
|
|
|
if ((expected_reply_len > lx20_max_reply_len_bytes) ||
|
|
(expected_reply_len < 2)) {
|
|
return false;
|
|
}
|
|
|
|
if (!write_bytes((uint8_t*)send_msg,
|
|
strlen(send_msg))) {
|
|
return false;
|
|
}
|
|
|
|
if (!sf20_wait_on_reply(rx_bytes)) {
|
|
return false;
|
|
}
|
|
|
|
if ((rx_bytes[0] != expected_reply[0]) ||
|
|
(rx_bytes[1] != expected_reply[1]) ) {
|
|
return false;
|
|
}
|
|
|
|
for (uint8_t i=0; i<10; i++) {
|
|
if (_dev->read(rx_bytes, expected_reply_len)) {
|
|
break;
|
|
}
|
|
// give a bit of time for the remaining bytes to be available
|
|
hal.scheduler->delay(1);
|
|
}
|
|
|
|
return memcmp(rx_bytes, expected_reply, expected_reply_len) == 0;
|
|
}
|
|
|
|
/*
|
|
send a native command and fill a reply into a buffer. Used for
|
|
version string
|
|
*/
|
|
void AP_RangeFinder_LightWareI2C::sf20_get_version(const char* send_msg, const char *reply_prefix, char reply[15])
|
|
{
|
|
const size_t expected_reply_len = 16;
|
|
uint8_t rx_bytes[expected_reply_len + 1];
|
|
memset(rx_bytes, 0, sizeof(rx_bytes));
|
|
|
|
if (!write_bytes((uint8_t*)send_msg, strlen(send_msg))) {
|
|
return;
|
|
}
|
|
|
|
if (!sf20_wait_on_reply(rx_bytes)) {
|
|
return;
|
|
}
|
|
|
|
if ((rx_bytes[0] != uint8_t(reply_prefix[0])) ||
|
|
(rx_bytes[1] != uint8_t(reply_prefix[1])) ) {
|
|
return;
|
|
}
|
|
|
|
for (uint8_t i=0; i<10; i++) {
|
|
if (_dev->read(rx_bytes, expected_reply_len)) {
|
|
break;
|
|
}
|
|
// give a bit of time for the remaining bytes to be available
|
|
hal.scheduler->delay(1);
|
|
}
|
|
memcpy(reply, &rx_bytes[2], 14);
|
|
}
|
|
|
|
/* Driver first attempts to initialize the sf20.
|
|
* If for any reason this fails, the driver attempts to initialize the legacy LightWare LiDAR.
|
|
* If this fails, the driver returns false indicating no LightWare LiDAR is present.
|
|
*/
|
|
bool AP_RangeFinder_LightWareI2C::init()
|
|
{
|
|
if (sf20_init()) {
|
|
DEV_PRINTF("Found SF20 native Lidar\n");
|
|
return true;
|
|
}
|
|
if (legacy_init()) {
|
|
DEV_PRINTF("Found SF20 legacy Lidar\n");
|
|
return true;
|
|
}
|
|
DEV_PRINTF("SF20 not found\n");
|
|
return false;
|
|
}
|
|
|
|
/*
|
|
initialise lidar using legacy 16 bit protocol
|
|
*/
|
|
bool AP_RangeFinder_LightWareI2C::legacy_init()
|
|
{
|
|
union {
|
|
be16_t be16_val;
|
|
uint8_t bytes[2];
|
|
} timeout;
|
|
|
|
// Retrieve lost signal timeout register
|
|
const uint8_t read_reg = LIGHTWARE_LOST_SIGNAL_TIMEOUT_READ_REG;
|
|
if (!_dev->transfer(&read_reg, 1, timeout.bytes, 2)) {
|
|
return false;
|
|
}
|
|
|
|
// Check lost signal timeout register against desired value and write it if it does not match
|
|
if (be16toh(timeout.be16_val) != LIGHTWARE_TIMEOUT_REG_DESIRED_VALUE) {
|
|
timeout.be16_val = htobe16(LIGHTWARE_TIMEOUT_REG_DESIRED_VALUE);
|
|
const uint8_t send_buf[3] = {LIGHTWARE_LOST_SIGNAL_TIMEOUT_WRITE_REG, timeout.bytes[0], timeout.bytes[1]};
|
|
if (!_dev->transfer(send_buf, sizeof(send_buf), nullptr, 0)) {
|
|
return false;
|
|
}
|
|
}
|
|
|
|
// call timer() at 20Hz
|
|
_dev->register_periodic_callback(50000,
|
|
FUNCTOR_BIND_MEMBER(&AP_RangeFinder_LightWareI2C::legacy_timer, void));
|
|
|
|
return true;
|
|
}
|
|
|
|
/*
|
|
initialise using newer text based protocol
|
|
*/
|
|
bool AP_RangeFinder_LightWareI2C::sf20_init()
|
|
{
|
|
// version strings for reporting
|
|
char version[15] {};
|
|
|
|
sf20_get_version("?P\r\n", "p:", version);
|
|
|
|
if (version[0]) {
|
|
DEV_PRINTF("SF20 Lidar version %s\n", version);
|
|
}
|
|
|
|
// Makes sure that "address tagging" is turned off.
|
|
// Address tagging starts every response with "0x66".
|
|
// Turns off Address Tagging just in case it was previously left on in the non-volatile configuration.
|
|
sf20_disable_address_tagging();
|
|
// Disconnect the servo (if applicable)
|
|
sf20_send_and_expect("#SC,0\r\n", "sc:0");
|
|
|
|
// Change the power consumption:
|
|
// 0 = power off
|
|
// 1 = power on
|
|
// As of 7/10/17 sw and fw version 1.0 the "#E,1" command does not seem to be supported.
|
|
// When it is supported the expected response would be "e:1".
|
|
|
|
// Changes the number of lost signal confirmations: 1 [1..250].
|
|
if (!sf20_send_and_expect("#LC,20\r\n", "lc:20")) {
|
|
return false;
|
|
}
|
|
|
|
#if 0
|
|
// This location in the code may be uncommented to do a one time change of the devices address.
|
|
// It should be commented out again and immediately reloaded to the pixhawk after the device has
|
|
// been modified by this initialization process.
|
|
// Address change to 0x65 = 101
|
|
write_bytes((uint8_t*)"#CI,0x65\r\n",10);
|
|
_dev->set_address(0x65);
|
|
uint8_t rx_bytes[lx20_max_reply_len_bytes + 1];
|
|
sf20_wait_on_reply(rx_bytes);
|
|
// Save the comm settings
|
|
if (!sf20_send_and_expect("%C\r\n", "%c:")) {
|
|
return false;
|
|
}
|
|
#endif
|
|
|
|
#if 0
|
|
/*
|
|
this can be used to change the laser encoding pattern
|
|
Changes the laser encoding pattern: 3 (Random A) [0..4].
|
|
*/
|
|
if (!sf20_send_and_expect("#LE,3\r\n", "le:3")) {
|
|
return false;
|
|
}
|
|
#endif
|
|
|
|
// Sets datum offset [-10.00 ... 10.00].
|
|
if (!sf20_send_and_expect("#LO,0.00\r\n", "lo:0.00")) {
|
|
return false;
|
|
}
|
|
|
|
// Changes to a new measuring mode (update rate):
|
|
// 1 = 388 readings per second
|
|
// 2 = 194 readings per second
|
|
// 3 = 129 readings per second
|
|
// 4 = 97 readings per second
|
|
// 5 = 78 readings per second
|
|
// 6 = 65 readings per second
|
|
// 7 = 55 readings per second
|
|
// 8 = 48 readings per second
|
|
if (!sf20_send_and_expect("#LM,7\r\n", "lm:7")) {
|
|
return false;
|
|
}
|
|
|
|
// Changes the gain boost value:
|
|
// Adjustment range = -20.00 ... 5.00
|
|
if (!sf20_send_and_expect("#LB,0.00\r\n", "lb:0.00")) {
|
|
return false;
|
|
}
|
|
|
|
// Switches distance streaming on or off:
|
|
// 0 = off
|
|
// 1 = on
|
|
if (!sf20_send_and_expect("#SU,1\r\n", "su:1")) {
|
|
return false;
|
|
}
|
|
|
|
// Changes the laser state:
|
|
// 0 = laser is off
|
|
// 1 = laser is running
|
|
if (!sf20_send_and_expect("#LF,1\r\n", "lf:1")) {
|
|
return false;
|
|
}
|
|
|
|
// Requests the measurement specified in the first stream.
|
|
write_bytes((uint8_t*)init_stream_id[0], strlen(init_stream_id[0]));
|
|
|
|
// call timer() at 20Hz
|
|
_dev->register_periodic_callback(50000,
|
|
FUNCTOR_BIND_MEMBER(&AP_RangeFinder_LightWareI2C::sf20_timer, void));
|
|
|
|
return true;
|
|
}
|
|
|
|
// read - return last value measured by sensor
|
|
bool AP_RangeFinder_LightWareI2C::legacy_get_reading(float &reading_m)
|
|
{
|
|
be16_t val;
|
|
|
|
const uint8_t read_reg = LIGHTWARE_DISTANCE_READ_REG;
|
|
|
|
// read the high and low byte distance registers
|
|
if (_dev->transfer(&read_reg, 1, (uint8_t *)&val, sizeof(val))) {
|
|
int16_t signed_val = int16_t(be16toh(val));
|
|
if (signed_val < 0) {
|
|
// some lidar firmwares will return 65436 for out of range
|
|
reading_m = uint16_t(max_distance_cm() + LIGHTWARE_OUT_OF_RANGE_ADD_CM) * 0.01f;
|
|
} else {
|
|
reading_m = uint16_t(signed_val) * 0.01f;
|
|
}
|
|
return true;
|
|
}
|
|
return false;
|
|
}
|
|
|
|
// read - return last value measured by sf20 sensor
|
|
bool AP_RangeFinder_LightWareI2C::sf20_get_reading(float &reading_m)
|
|
{
|
|
// Parses up to 5 ASCII streams for LiDAR data.
|
|
// If a parse fails, the stream measurement is not updated until it is successfully read in the future.
|
|
uint8_t stream[lx20_max_expected_stream_reply_len_bytes+1]; // Maximum response length for a stream ie "ldf,0:40.99" is 11 characters
|
|
|
|
uint8_t i = streamSequence[currentStreamSequenceIndex];
|
|
size_t num_processed_chars = 0;
|
|
|
|
/* Reads the LiDAR value requested during the last interrupt. */
|
|
if (!_dev->read(stream, sizeof(stream))) {
|
|
return false;
|
|
}
|
|
stream[lx20_max_expected_stream_reply_len_bytes] = 0;
|
|
|
|
if (!sf20_parse_stream(stream, &num_processed_chars, parse_stream_id[i], sf20_stream_val[i])) {
|
|
return false;
|
|
}
|
|
|
|
if (i==0) {
|
|
reading_m = sf20_stream_val[0] * 0.01f;
|
|
}
|
|
|
|
// Increment the stream sequence
|
|
currentStreamSequenceIndex++;
|
|
if (currentStreamSequenceIndex >= numStreamSequenceIndexes) {
|
|
currentStreamSequenceIndex = 0;
|
|
}
|
|
i = streamSequence[currentStreamSequenceIndex];
|
|
|
|
// Request the next stream in the sequence from the SF20
|
|
write_bytes((uint8_t*)init_stream_id[i], strlen(init_stream_id[i]));
|
|
|
|
return true;
|
|
}
|
|
|
|
bool AP_RangeFinder_LightWareI2C::sf20_parse_stream(uint8_t *stream_buf,
|
|
size_t *p_num_processed_chars,
|
|
const char *string_identifier,
|
|
uint16_t &val)
|
|
{
|
|
size_t string_identifier_len = strlen(string_identifier);
|
|
for (uint32_t i = 0 ; i < string_identifier_len ; i++) {
|
|
if (stream_buf[*p_num_processed_chars] != string_identifier[i]) {
|
|
return false;
|
|
}
|
|
(*p_num_processed_chars)++;
|
|
}
|
|
|
|
/*
|
|
special case for being beyond maximum range, we receive a message like this:
|
|
ldl,1:-1.00
|
|
we will return max distance
|
|
*/
|
|
if (strncmp((const char *)&stream_buf[*p_num_processed_chars], "-1.00", 5) == 0) {
|
|
val = uint16_t(max_distance_cm() + LIGHTWARE_OUT_OF_RANGE_ADD_CM);
|
|
(*p_num_processed_chars) += 5;
|
|
return true;
|
|
}
|
|
|
|
/* Number is always returned in hundredths. So 6.33 is returned as 633. 6.3 is returned as 630.
|
|
* 6 is returned as 600.
|
|
* Extract number in format 6.33 or 123.99 (meters to be converted to centimeters).
|
|
* Percentages such as 100 (percent), are returned as 10000.
|
|
*/
|
|
uint32_t final_multiplier = 100;
|
|
bool decrement_multiplier = false;
|
|
bool number_found = false;
|
|
uint16_t accumulator = 0;
|
|
uint16_t digit_u16 = (uint16_t)stream_buf[*p_num_processed_chars];
|
|
while ((((digit_u16 <= '9') &&
|
|
(digit_u16 >= '0')) ||
|
|
(digit_u16 == '.')) &&
|
|
(*p_num_processed_chars < lx20_max_reply_len_bytes)) {
|
|
(*p_num_processed_chars)++;
|
|
if (decrement_multiplier) {
|
|
final_multiplier /=10;
|
|
}
|
|
if (digit_u16 == '.') {
|
|
decrement_multiplier = true;
|
|
digit_u16 = (uint16_t)stream_buf[*p_num_processed_chars];
|
|
continue;
|
|
}
|
|
number_found = true;
|
|
accumulator *= 10;
|
|
accumulator += digit_u16 - '0';
|
|
digit_u16 = (uint16_t)stream_buf[*p_num_processed_chars];
|
|
}
|
|
|
|
accumulator *= final_multiplier;
|
|
val = accumulator;
|
|
return number_found;
|
|
}
|
|
|
|
/*
|
|
update the state of the sensor
|
|
*/
|
|
void AP_RangeFinder_LightWareI2C::update(void)
|
|
{
|
|
// nothing to do - its all done in the timer()
|
|
}
|
|
|
|
void AP_RangeFinder_LightWareI2C::legacy_timer(void)
|
|
{
|
|
if (legacy_get_reading(state.distance_m)) {
|
|
// update range_valid state based on distance measured
|
|
update_status();
|
|
} else {
|
|
set_status(RangeFinder::Status::NoData);
|
|
}
|
|
}
|
|
|
|
void AP_RangeFinder_LightWareI2C::sf20_timer(void)
|
|
{
|
|
if (sf20_get_reading(state.distance_m)) {
|
|
// update range_valid state based on distance measured
|
|
update_status();
|
|
} else {
|
|
set_status(RangeFinder::Status::NoData);
|
|
}
|
|
}
|
|
|
|
// Only for use during init as this blocks while waiting for the SF20 to be ready.
|
|
bool AP_RangeFinder_LightWareI2C::sf20_wait_on_reply(uint8_t *rx_two_byte)
|
|
{
|
|
// Waits for a non-zero first byte while repeatedly reading 16 bits.
|
|
// This is used after a read command to allow the sf20 time to provide the result.
|
|
uint32_t start_time_ms = AP_HAL::millis();
|
|
const uint32_t max_wait_time_ms = 50;
|
|
|
|
while (AP_HAL::millis() - start_time_ms < max_wait_time_ms) {
|
|
if (!_dev->read(rx_two_byte, 2)) {
|
|
hal.scheduler->delay(1);
|
|
continue;
|
|
}
|
|
if (rx_two_byte[0] != 0) {
|
|
// normal exit
|
|
return true;
|
|
}
|
|
}
|
|
return false;
|
|
}
|
|
|
|
#endif // AP_RANGEFINDER_LWI2C_ENABLED
|