Commit Graph

107 Commits

Author SHA1 Message Date
Peter Barker ef0de65347 AP_InertialSensor: tidy IMU killing 2024-07-10 18:17:00 +10:00
muramura e48044dc45 AP_InertialSensor: Clearly state the maximum G-force 2024-07-10 10:07:16 +10:00
Andy Piper a86f4fdc8f AP_InertialSensor: move gyro and accel instance ids into AP_InertialSensor_Backend 2024-06-26 17:14:56 +10:00
Peter Barker 6a897f01d8 AP_InertialSensor: allow compilation with HAL_LOGGING_ENABLED false 2024-01-17 18:25:55 +11:00
Andy Piper da0b1402d3 AP_InertialSensor: add high-resolution reads for ICM45686
enable high-resolution support on all ICM4xxxx sensors
create INS_HIRES_SAMPLE mask
adjust high-resolution sampling for correct byte ordering and depth
correct high resolution scaling on 18bit ICM4xxxx IMUs
control highres via HAL_INS_HIGHRES_SAMPLE
2023-10-25 19:23:11 +11:00
Andrew Tridgell b6c9ac2569 AP_InertialSensor: added optional FIFO rate logging to invensensev3 driver
this is useful for tracking down and confirming the stuck gyro issue
on the ICM42688
2023-10-22 15:09:40 +11:00
Iampete1 3429276224 AP_InertialSensor: add INS_RAW_LOG_OPT to allow raw logging of post, and pre+post on primary or all gyros 2023-10-03 10:24:58 +11:00
jfbblue0922 458fbb7f90 AP_InertialSensor: add SCHA63T IMU support 2023-05-10 17:24:02 +10:00
Andy Piper 4aafb3ab71 AP_InertialSensor: fast sampling for ICM45686
Fix accel scale on ICM45686
2023-02-22 18:06:46 +11:00
Andy Piper 90cdc1aa52 AP_InertialSensor: allow FFT window to be captured post-filter
selectively apply filters twice to make sure that FFT is not tracking itself
clean-up notch disablement for non-DSP builds
use filter gyro data for FFT when analysing post-filter
always apply LPF after all of the notches
move to a phased application of window information for FFT
tap FFT gyro window at the appropriate place for downsampled FFTs
add accessor for FFT notch
document notch uses cases and flow
2022-12-28 18:14:56 +11:00
bugobliterator 35f05738d0 AP_InertialSensor: add support for ICM45686 IMU 2022-11-01 10:41:59 +11:00
Andrew Tridgell 5bde9b0e7c AP_InertialSensor: added support for ICM42670 IMU 2022-08-02 17:26:46 +10:00
Peter Barker e4ce4ebed3 AP_InertialSensor: remove un-needed methods 2022-07-19 10:30:36 +10:00
Andrew Tridgell a37f268dc6 Ap_Inertialsensor: by default only run harmonic notch on the active gyro
this should save quite a lot of CPU. Only the active gyro impacts
vehicle flight
2022-06-12 15:39:44 +10:00
Leonardo Garcia 0eb6ae365a AP_InertialSensor: Added BMI085 support
Fixed styling for 61125e2

Remove whitespace l202

Removed else
2022-04-27 18:37:39 +10:00
Andrew Tridgell e2e1e74da5 AP_InertialSensor: switch to HarmonicNotch class
this makes the logic much easier to follow, without indexes into
arrays
2022-04-19 09:39:03 +10:00
Andrew Tridgell e67d9b4179 AP_InertialSensor: support two full harmonic notch filters 2022-04-19 09:39:03 +10:00
Andy Piper 29e8f96275 AP_InertialSensor: move frontend update into ramfunc. 2022-04-12 09:19:45 +10:00
Andy Piper c7a43f2a90 AP_InertialSensor: put some functions in fast ram
precisely split backend/frontend on Invensense for RAMFUNC allocation
allow building with no IMUs
2022-02-09 12:47:55 +00:00
Andy Piper 3fd79b8ffb AP_InertialSensor: BMI270 driver 2021-12-31 09:25:29 +11:00
Andrew Tridgell 662327f2ea AP_InertialSensor: added support for more ADIS IMUs
support 32 bit delta angles and velocities
2021-12-29 18:25:18 +11:00
QioTek 586c2064a6 AP_InertialSensor: added support for IIM-42652 and ICM-40605 sensors
handle new Invensense v3 sensor types
2021-12-14 11:38:36 +11:00
Josh Henderson 2b20dcf128 AP_InertialSensor: move GYR & ACC logging functions to Logging.cpp 2021-05-01 14:15:58 +10:00
Andrew Tridgell 4cddf37984 AP_InertialSensor: log unexpected register changes
when the register checking code finds an error we will log what
register changed and to what value
2021-02-24 18:18:37 +11:00
Andrew Tridgell 957842f7eb AP_InertialSensor: added support for v3 Invensense sensors
starting with ICM-40609, ICM-42688 and ICM-42605
2021-01-11 14:43:35 +11:00
Andrew Tridgell b74e5c0e2f AP_InertialSensor: added ExternalAHRS backend 2021-01-05 21:13:12 +11:00
Andy Piper faf9bbbf3a AP_InertialSensor: make the backend fast gyro rate configurable
raise gyro rate default on F7 and H7
clean up gyro rate docs and output startup banner
2020-07-10 16:45:29 +10:00
Andy Piper 61bb42cc0c AP_InertialSensor: allow up to four distinct notch center frequencies to be updated
apply the LPF after the notch filters to reduced notch-induced noise
2020-06-21 19:09:35 +10:00
Andy Piper 8ac79da643 AP_InertialSensor: FFT gyro window would overflow on windows >= 256
convert FFT buffers to ObjectBuffer<float> for lock-free access
push gyro samples directly into the FFT ring buffer from the gyro thread
2020-05-24 07:43:34 +10:00
Andrew Tridgell d772289b0d AP_InertialSensor: added driver for ADIS16470 2020-04-13 11:57:04 +10:00
Andy Piper 3d9776dd6d AP_InertialSensor: expose statically filtered gyro values for FFT analysis and allow sampling to gyro window for FFT analysis.
FFT windows can be dynamically allocated
add harmonic notch dynamic tracking mode
unwind gyro window allocation in the case of failure
allow access to harmonic notch harmonics
2020-02-22 11:15:37 +11:00
Andrew Tridgell 58708c483f AP_InertialSensor: make all semaphores recursive
the cost is very similar and this prevents an easy coding error which
can occur on less used code paths
2020-01-19 20:19:30 +11:00
Andrew Tridgell 9dc618ddd4 AP_InertialSensor: added gyro_harmonic_notch_enabled() 2019-11-19 07:08:01 +08:00
Andy Piper 5b7f9f6bea AP_InertialSensor: while sensors are converging update the filters sample rates. if gyro filtering produces invalid output, keep the previous value 2019-09-11 18:41:05 +10:00
Andy Piper 3261677e01 AP_InertialSensor: remove _ prefix from methods. use changed filter methods. 2019-09-11 18:41:05 +10:00
Andy Piper 50f7e50634 AP_InertialSensor: add harmonic notch filter to gyro filter chain
Allow dynamic updates to the calculated frequency. Convert bandwidth and frequency to floats.
backend variables do not need to be indexed per-backed
2019-09-11 18:41:05 +10:00
Andy Piper 36878e9b3c AP_InertialSensor: Allow all filter frequencies to be 16bit. 2019-06-06 17:09:17 +10:00
Andy Piper 18d403c3ac AP_InertialSensor: Rework notch filter allocation and sampling
https://github.com/ArduPilot/ardupilot/issues/11346

Allocate a notch filter per-IMU.
Update the notch filters in the backend at the sensor sample rate.
Allow raw logging of post-filtered gyro and accel values.
2019-06-06 17:09:17 +10:00
Peter Barker e0fc73776c AP_InertialSensor: return floats from raw-sample-rate getters
The underlying type changed at some stage but the getters did not
2019-04-09 10:02:16 +10:00
na 494a3f86ad AP_IntertialSensor: support ICM20601 IMU 2019-03-28 09:15:27 +11:00
Siddharth Purohit 8c2d3945de AP_IneertialSensor: add support for custom accel scale
adds support for 30g measurement on ICM20649
2019-03-21 18:54:32 +11:00
Andrew Tridgell 81cd103073 AP_InertialSensor: probe for new v2 invensense IMUs
also suppress LSM9DS0 whoami warnings, as these will now be common
with new IMUs

and make 20602 show up as a new devtype so we can distinguish it
2019-03-11 12:40:21 +11:00
Siddharth Purohit 528c0b4d7c AP_InertialSensor: add drivers for register bank based Invensense Sensors 2019-03-06 20:47:10 +11:00
Andrew Tridgell 6048c10a7c AP_InertialSensor: added driver for BMI088
setup for 1600 Hz accel sample, 2kHz gyro sample, 24g accel range
2019-01-31 12:05:57 -08:00
Andrew Tridgell 9520f5f768 AP_InertialSensor: removed F4Light 2019-01-21 21:57:21 +11:00
Peter Barker b47733142f GLOBAL: rename DataFlash_Class to AP_Logger 2019-01-18 18:08:20 +11:00
Andrew Tridgell 755dc8dc5d AP_InertialSensor: use WITH_SEMAPHORE()
and removed usage of hal.util->new_semaphore()
2018-10-17 12:54:22 +11:00
Andrew Tridgell 5f8b57ba19 AP_InertialSensor: added SITL device IDs 2018-07-13 10:19:01 +10:00
Andrew Tridgell 89b8124560 AP_InertialSensor: added BMI055 IMU driver 2018-06-08 09:56:41 +10:00
Peter Barker 1a640e3405 AP_InertialSensor: parameterise sensor-rate logging, generalise it
AP_InertialSensor: add parameters for push-to-log interval and count

AP_InertialSensor: rename BAT_RAW to BAT_OPT

This becomes a bitmask of options for the BatchSampler

AP_InertialSensor: rename 'fast sample' to 'sensorrate sample'

AP_InertialSensor: const sensor-rate filter method

AP_InertialSampler: remove hard-coding of sample rate multiplier

AP_InertialSensor: use parameter to enable/disable sensor-rate logging

AP_InertialSensor: use a parameter to control sensor-rate logging

AP_InertialSensor: allow backends to override sensor data multiplier

e.g. some accelerometers are sensitive over wider ranges than the default 16G

AP_Inertialsensor: correct sample rate multiplier
2018-05-01 09:35:29 +10:00