Before: -> After
Stabilize P –> Stabilize P (Use NG values, or 8.3 x the older AC2 value)
Stabilize I –> Stabilize I (Stays same value)
Stabilize D –> Rate P (Stays same value)
–> Rate I (new)
Added a new value – an I term for rate. The old stabilization routines did not use this term. Please refer to the config.h file to read more about the new PIDs.
Added framework for using DCM corrected Accelerometer rates. Code is commented out for now.
Added set home at Arming.
Crosstrack is now a full PID loop, rather than just a P gain for more control.
Throttle now slews when switching out of Alt hold or Auto modes for less jarring transitions
Sonar and Baro PIDs are now combined into a throttle PID Yaw control is completely re-written.
Added Octa_Quad support - Max
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2836 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added Octo Support
Fixed Loiter issue regarding Yaw towards loiter location
Added Yaw control alternative for testing
decreased Yaw deadband to +-5°
revved to 2.0.10
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2389 f9c3cf11-9bcb-44bc-f272-b75c42450872
Cleanups, better logs for Alt hold, yaw debugging
I tuned up Hein's Hexa Yaw. I think we may need to adjust Yaw gains based on Frame type.
Crossing fingers, the next rev is the final.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2381 f9c3cf11-9bcb-44bc-f272-b75c42450872
updated motor setup test to be sequencial pulses of the motors in CW order.
Fixed Mission scripting logic
fixed Free yaw error in neutral throttle
fixed D term issue with Baro hold - was too high
incremented firmware revision, removed frame var
removed setup show from startup
removed unused EEPROM functions
fixed broken demo mission
fixed non working loiter with delay
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2275 f9c3cf11-9bcb-44bc-f272-b75c42450872
The trunk is unstable, so please be careful. I've made a lot of changes based on the Sparkfun challange. Most include how we handle things like altitude, but the mission scripting has also been updated as well.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1920 f9c3cf11-9bcb-44bc-f272-b75c42450872
Takeoff now works well.
better logging.
tuned down kD for Yaw - was causing some bad behavior.
Auto mission now resets when entering mode.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1914 f9c3cf11-9bcb-44bc-f272-b75c42450872
Logs updated to do better Yaw Debugging
Landing is now rate limited
updated command desctiption.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1911 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added AP_Var Fingerprint checker. Will not let users fly with OOD firmware.
Tweaked Yaw to give better response. Let me know how it goes. It looks fine, but I've not flown it.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1878 f9c3cf11-9bcb-44bc-f272-b75c42450872
removed FBW mode - no longer needed
added set_throttle_cruise_flag to auto set the throttle value for alt hold
added altitude minimum option for waypoints
added support for relative WPs
added support for Yaw tracking per WP in options bitmask
lowered default sonar kD value
increased minimal value to set the throttle cruise value with CH7 switch
updated README.txt
added additional stock test missions available in CLI
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1856 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added new navigation control based on bearing_error so we can leverage Crosstrack correction.
I've done limited testing on this.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1773 f9c3cf11-9bcb-44bc-f272-b75c42450872
this fixes the build with HIL_MODE_ATTITUDE and MAVLink enabled. Basic
MAVLink operation works.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1737 f9c3cf11-9bcb-44bc-f272-b75c42450872
jasonshort
dhcorley@msn.com
rmackay9@yahoo.com
tridge60@gmail.com