this is the last of the delays that can cause the EKF to get unhappy
on arming in copter. The comment says it is waiting for RC input, but
I don't think that makes any sense any more.
Further to refactor of RC_Channel class which included
adding get_xx set_xx methods, change reads and writes to the public members
to calls to get and set functionsss
old public member(int16_t) get function -> int16_t set function (int16_t)
(expression where c is an object of type RC_Channel)
c.radio_in c.get_radio_in() c.set_radio_in(v)
c.control_in c.get_control_in() c.set_control_in(v)
c.servo_out c.get_servo_out() c.set_servo_out(v)
c.pwm_out c.get_pwm_out() // use existing
c.radio_out c.get_radio_out() c.set_radio_out(v)
c.radio_max c.get_radio_max() c.set_radio_max(v)
c.radio_min c.get_radio_min() c.set_radio_min(v)
c.radio_trim c.get_radio_trim() c.set_radio_trim(v);
c.min_max_configured() // return true if min and max are configured
Because data members of RC_Channels are now private and so cannot be written directly
some overloads are provided in the Plane classes to provide the old functionality
new overload Plane::stick_mix_channel(RC_Channel *channel)
which forwards to the previously existing
void stick_mix_channel(RC_Channel *channel, int16_t &servo_out);
new overload Plane::channel_output_mixer(Rc_Channel* , RC_Channel*)const
which forwards to
(uint8_t mixing_type, int16_t & chan1, int16_t & chan2)const;
Rename functions
RC_Channel_aux::set_radio_trim(Aux_servo_function_t function)
to RC_Channel_aux::set_trim_to_radio_in_for(Aux_servo_function_t function)
RC_Channel_aux::set_servo_out(Aux_servo_function_t function, int16_t value)
to RC_Channel_aux::set_servo_out_for(Aux_servo_function_t function, int16_t value)
Rationale:
RC_Channel is a complicated class, which combines
several functionalities dealing with stick inputs
in pwm and logical units, logical and actual actuator
outputs, unit conversion etc, etc
The intent of this PR is to clarify existing use of
the class. At the basic level it should now be possible
to grep all places where private variable is set by
searching for the set_xx function.
(The wider purpose is to provide a more generic and
logically simpler method of output mixing. This is a small step)
The is commit adds a new flight mode called 'Throw' to Copter that enables the copter to be thrown into the air to start motors. This mode can only be netered when the copters EKF has a valid position estimate and goes through the following states
Throw_Disarmed - The copter is disarmed and motors are off.
Throw_Detecting - The copter is armed, but motors will not spin unless THROW_MOT_START has been set to 1. The copter is waiting to detect the throw. A throw with an upwards velocity of at least 50cm/s is required to trigger the detector.
Throw_Uprighting - The throw has been detected and the copter is being uprighted with 50% throttle to maximise control authority. This state transitions when the copter is within 30 degrees of level.
Throw_HgtStabilise - The copter is kept level and height is stabilised about the target height which is 3m above the height at which the throw release was detected. This state transitions when the height is no more than 0.5m below the demanded height.
Throw_PosHold - The horizontal motion is arrested and the copter is kept at a constant position and height.
The PSTR is already define as a NOP for all supported platforms. It's
only needed for AVR so here we remove all the uses throughout the
codebase.
This was automated with a simple python script so it also converts
places which spans to multiple lines, removing the matching parentheses.
AVR-specific places were not changed.
Also, force rsc_control input to 0 when disarmed. This prevents condition where AP_MotorsHeli can receive a rotor speed command greater than zero while disarmed, which was causing the ColYaw function to move the rudder servo. These two changes are somewhat tied together as it required changing the arming_check to check the RSC_Control not desired_speed from AP_MotorsHeli.
Removed potentially endless loop caused by start_logging calling
Log_Write_Startup which called should_log which could then call
start_logging.
Moved disarm event logging above motors disarm so it is logged
Andrew Tridgell
Jonathan Challinger
skyscraper
Paul Riseborough
Randy Mackay
Luis Vale Gonçalves
Robert Lefebvre
Fredrik Hedberg
lvale
Lucas De Marchi
Paul Riseborough
Gustavo Jose de Sousa
Staroselskii Georgii
Siddharth Bharat Purohit
squilter