Commit Graph

73 Commits

Author SHA1 Message Date
Andrew Tridgell 92cd631ce5 Plane: added THR_PASS_STAB parameter
this allows direct passthru of throttle in STABILIZE and FBWA, which
is useful for nitro planes wher you have a throttle cut switch that
drops the throttle below normal minimum.
2012-11-26 23:33:05 +11:00
Andrew Tridgell 84300c85d6 APM: make it possible to run the CLI on any serial port 2012-11-21 21:41:34 +11:00
Andrew Tridgell 8f108e2eb3 APM: added AMP_OFFSET option
thanks to Alexey Kozin!
2012-11-21 13:34:27 +11:00
rmackay9 ef727bbb3c ArduPlane: move to use new INS library instead of IMU library 2012-11-07 19:21:03 +09:00
Andrew Tridgell 8652bfee8d APM: added RSSI_PIN option for receiver RSSI
this allows you to configure the pin for receiver RSSI without
recompiling
2012-11-06 22:04:41 +11:00
Andrew Tridgell e479af67ff APM: fixed loiter radius docs to reflect new limit 2012-10-30 16:19:24 +11:00
rmackay9 775489d658 ArduPlane: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery monitor 2012-10-13 20:51:41 +09:00
Andrew Tridgell 6bae5ecd51 APM: added THR_SUPP_MAN option
this allows for manual throttle control during auto throttle
suppression. This is useful for keeping a petrol engine idling before
takeoff
2012-09-22 20:17:06 +10:00
Andrew Tridgell cebb67e1df APM: removed the unused sonar code
when we start supporting a sonar we'll add a AP_Sonar library, like
AP_Airspeed
2012-09-19 19:35:22 +10:00
Andrew Tridgell 2324997e16 APM: added ALT_OFFSET parameter
useful to adjust for barometric pressure changes during a long flight
2012-09-19 16:23:25 +10:00
Andrew Tridgell 5c3595e0dc APM: fixed throttle nudging
The nudge value depended on RC3_TRIM, which is not a reliable
value. It tried to only take effect when the throttle stick was above
50%, but if RC3_TRIM was high for some reason (say 1500) then it would
actually depress the throttle by a large amount, which could cause the
plane to stall.

This also adds a boolean option THROTTLE_NUDGE to allow disabling of
throttle nudging
2012-09-09 19:39:04 +10:00
Andrew Tridgell 164c60d25f APM: added RUDDER_STEER option
when enabled, this uses only the rudder to steer during takeoff and
landing, using aileron only for levelling
2012-09-08 10:07:03 +10:00
Andrew Tridgell 96ea350143 APM: added XTRK_MIN_DIST option
this allows you to disable crosstrack correction on short legs
2012-09-08 10:06:44 +10:00
Andrew Tridgell 9a987ce116 APM: fixed docs for LIM_PITCH_MIN 2012-08-30 14:55:08 +10:00
Andrew Tridgell f6c3197cd2 APM: added new TELEM_DELAY parameter
number of seconds to delay telemetry
2012-08-30 08:59:39 +10:00
Andrew Tridgell fce01464b1 APM: added ALT_CTRL_ALG parameter
this allows you to select different altitude control algorithms. The
current choices are for the default (automatic based on if airspeed is
available), or to force a non-airspeed algorithm

The idea is to make it possible to use airspeed for some things (like
wind speed, speed scaling) but not for alt control
2012-08-28 20:18:24 +10:00
Andrew Tridgell c9cf483822 APM: added XTRK_USE_WIND parameter
when enabled this will use the wind estimation code to adjust the
navigation bearing, allowing the navigation code to cope with much
higher levels of wind while using a compass
2012-08-25 17:49:26 +10:00
Andrew Tridgell d445482ace APM: added optional use of new APM_Control library
thanks to Jon Challinger for the new controllers!
2012-08-22 12:45:14 +10:00
uncrustify 0f415bbc6a uncrustify ArduPlane/Parameters.pde 2012-08-21 19:19:50 -07:00
Andrew Tridgell bf2319a0fc AHRS: fixed reference to AHRS var_info for APM and ACM 2012-08-21 15:58:32 +10:00
rmackay9 6d489947cf ArduPlane: replaced many "int" with "int16_t", "long" with "int32_t" 2012-08-18 18:26:13 +09:00
Andrew Tridgell 5e690d5680 APM: added parameter FBWB_ELEV_REV
this fixes issue 343
2012-08-17 15:04:53 +10:00
Andrew Tridgell ad73c229ab APM: added LAND_FLARE_ALT and LAND_FLARE_SEC
these allow you to configure the altitude and time before touchdown to
flare the plane and lock the heading. Useful on larger planes.
2012-08-15 18:11:16 +10:00
Andrew Tridgell 1252ddfe0c APM: rename RDRSTEER to WHEELSTEER
thanks to Jon for the suggestion
2012-08-15 16:28:59 +10:00
Andrew Tridgell e26e8b3b67 APM: added RDRSTEER_ PID for steering on ground
this allows for rolling takeoff with steering, and use of rudder in
landing
2012-08-15 12:39:35 +10:00
Andrew Tridgell 817017658d APM: implement FENCE_ACTION_REPORT
when FENCE_ACTION is set to FENCE_ACTION_REPORT a fence breach is
reported, but the flight mode is not changed
2012-08-15 12:39:35 +10:00
Andrew Tridgell 2865434d02 APM: added 'OBC' failsafe module for ArduPlane
this adds FS_* parameters for setting up APM to follow the outback
challenge failsafe rules.

This includes:

 - manual pin
 - heartbeat pin
 - waypoint for heartbeat failure
 - waypoint for GPS failure
2012-08-15 12:39:34 +10:00
Andrew Tridgell 3bdc7d41be INS: disable INS AP_Param table when not on APM1 hardware
this could cause overwriting of memory with default values
2012-08-11 22:06:03 +10:00
Andrew Tridgell 5498d347f3 APM: Added RST_MISSION_CH option
this allows a pilot to reset the mission using a transmitter
switch. Very useful for repeating a mission during testing
2012-08-09 10:33:16 +10:00
Andrew Tridgell e133900c68 APM: Added STICK_MIXING option
this replaces the compile time option. Disabling during long distance
flights when the transmitter may be out of range is useful.
2012-08-09 08:53:29 +10:00
Amilcar Lucas d34549f386 Add an optional second mount to ArduPlane and ArduCopter 2012-08-08 23:22:24 +02:00
Andrew Tridgell 5bfd1200d6 APM: change variables to use _cm, _cd and _ms suffix for units
this makes it less likely that we mix up units
2012-08-08 12:12:30 +10:00
Andrew Tridgell a823c9ceae APM: removed cli slider and dipswitch options
use mavlink/eeprom for all config
2012-08-08 12:12:29 +10:00
Andrew Tridgell 12cd6b68ff AP_Param: update ArduPlane core for new AP_Param interface 2012-08-08 12:11:57 +10:00
rmackay9 176e6fdd68 ArduPlane: bug fix to global var_info parameter list for ahrs object. 2012-08-01 10:52:34 +09:00
Andrew Tridgell cb61c3be96 APM: fixed case of 'LAND_PITCH_CD'
mavlink parameters are uppercase by convention
2012-07-29 17:07:38 +10:00
rmackay9 06e35820e5 ArduPlane: allow MPU6000's DMP to be used for attitude estimation.
Enable by adding this line to APM_Config.h:
#define DMP_ENABLED ENABLED
2012-07-28 19:50:40 +09:00
rmackay9 842ce47219 ArduPlane: change to Parameters.pde to support moving var_info from AP_AHRS to AP_AHRS_DCM 2012-07-28 14:31:01 +09:00
Andrew Tridgell 6bcfe913f7 APM: added a SCALING_SPEED parameter
this allows users to adjust the base speed used for scaling roll/pitch
PIDs. This can be used to make PIDs work for both airspeed and
non-airspeed control
2012-07-26 11:30:23 +10:00
Andrew Tridgell 3c2fc72654 APM: fixed HIL build 2012-07-26 10:09:07 +10:00
Jason Short 98237a0e00 Added Oilpan INS group object param 2012-07-18 23:07:50 -07:00
Jeff Taylor d02655ac56 APM: Fixed bug where landing_pitch wasnt initialized properly
this adds a new LAND_PITCH_CD parameter to control the landing pitch
when an airspeed sensor is not being used
2012-07-19 13:59:30 +10:00
Andrew Tridgell d6e370886f APM: rename airspeed_cruise to airspeed_cruise_cm to make the units clearer
it is in cm/s, not m/s
2012-07-19 11:50:41 +10:00
Amilcar Lucas 3d385c0fb4 ArduPlane parameters: re-order the files, looks like the second file gets ignored :( 2012-07-18 22:52:17 +02:00
Amilcar Lucas 8a8e11fa7f ArduPlane parameters: Add base class info as well 2012-07-18 22:39:49 +02:00
Amilcar Lucas 610fdeacc1 Support up to 11 servos in APM2
Conflicts:

	ArduPlane/ArduPlane.pde
2012-07-18 22:01:19 +02:00
Michael Oborne 636fcadde4 fix rc libray param gen 2012-07-18 07:03:39 +08:00
Andrew Tridgell de3c9ce56d Airspeed: change APM to use new AP_Airspeed library
the next step is AHRS dead reckoning
2012-07-16 11:21:50 +10:00
Michael Oborne 67ecaa9252 AP fix duplicate keys in param config 2012-07-13 07:06:01 +08:00
Amilcar Lucas dfe0983e1e Merge the changes from APM_Camera branch into ArduCopter
Conflicts:

	ArduCopter/Camera.pde
	ArduCopter/Parameters.pde
2012-07-11 00:39:13 +02:00