add support for undef of STM32 lines and DMA_NOMAP
add support for F103 running at 24Mhz
add f103 variants of iofirmware
reduce memory usage in iomcu for new model
correct pwm output reporting
split iofirmware into config + mcu to allow f103 definition
don't enable non-existant timers on F103
enable TIM4 in shared mode on IOMCU for dshot
stop the PWM peripheral in rcout DMA swapping on IOMCU to prevent UART corruption
provide debugging options on iomcu dshot
support unshared DMA with iomcu dshot
optimize rcout on iomcu
tune iomcu stack for 8 channels
set timer counter size to be a byte wide
use HAL_DSHOT_ENABLED instead of DISABLE_DSHOT
build iomcu-dshot from existing iomcu
correct defines for DMAR size on iomcu
allow iomcu dshot rate to be configured from FMU
correct DMA allocation for dshot on iomcu
allow debug builds on iofirmware
ensure dshot is enabled on iomcu dshot
support proper iomcu dshot output thread triggered by FMU
allow selective disablement of serial LEDs and passthrough
disable serial LEDs and passthrough on iomcu-dshot
propagate ESC telemetry to iomcu
dshot_send_groups() for iomcu
remove use of ICU on iomcu for dshot. only allocate possible DMA channels
rename serial passthrough and dshot defines
update dshot docs
resize dshot iomcu main stack to minimum
correct dshot prescaler usage and bit_width_mul calculation
use ChibiOS in tickless mode on iomcu-dshot so that virtual timers can be used
propagate dshot commands to iomcu
passthrough oneshot125 to iomcu
LED processing on a separate thread allows much longer LED lengths to be handled without
compromising dshot timing or timeouts. The thread is also run at a lower priority to
reflect its lack of flight criticality
convert RCOutput to new virtual timer interface
cope with SDC vs SDMMC
use new SPIv3 driver. Correct clocks for SDMMCv2.
add STM32L431 support
port ChibiOS config to version 8
support SPIv3 driver model v2 on H7
use currcore in debug options
use new mmc API
disable speed optimizations in the bootloader to save a little flash
upgrade to halconf v8.4
relax constraints on QSP/flash clock.
add support for disabling QSPI reset in main firmware
this prevents bad calculated timeouts in DShot. The timeout would
sometimes come out as 0xFFFFFFFF, which led to an assert and could
block the thread
This fix is meant to be minimilistic to allow it to be merged easily
into 4.2. A better fix would fix all the uint32_t wrap handling in
DShot
make sure debug will compile
take into account active channels when configuring bdshot
add channel mask debug output
correct set bdshot telemetry position at startup
make sure all channels in a bdshot group are pulled high to prevent spurious pulses
hwdef for DevEBoxH7v2
pin definitions for STM32H750
add QSPI to DevEBox bootloader
add external flash to DevEBox
rename EXTERNAL_PROG_FLASH_MB to EXT_FLASH_SIZE_MB
Add support for EXT_FLASH_RESERVE_START_KB and EXT_FLASH_RESERVE_END_KB
Disable HAL_ENABLE_SAVE_PERSISTENT_PARAMS when there is no bootloader flash available
relax storage health status with SD card backend
don't check SD card health unless USE_POSIX
binary sections rearranged on external ram
manage RAMFUNC through ldscript and optimize function placement in external flash
inline timer functions
optimize placement of ChibiOS and functions in ITCM and AXI RAM
fix chibios features on bootloader build with external flash
change H750 memory layout
increase line storage for SD card based parameters
comment external flash linker script
move vtables into DTCM
update ram map for H757
enable crashdump support with external flash
correct bootloader pins and generator on SPRacingH7/DevEBoxH7v2
setup external flash reserve regions
allow different RAM_MAP for external flash on H750 and H757
fixes frequency setup for neopixel, separating out DShot setup. Also
allows for neopixel without other DMA controlled output types for LEDs
in AP_Periph
Andy Piper
bugobliterator
Andrew Tridgell
Peter Barker
Iampete1
Randy Mackay
Michel Pastor