6a769b728e
Plane: fixed yaw on the ground when rudder disarming in AUTO
...
when a quadplane touches down in an auto throttle mode the pilot may
use rudder to disarm. The check for rudder disarm was only active in
modes without auto-throttle. This expands it to all modes if the
throttle has hit the lower limit
2022-03-28 20:53:56 +11:00
04f464772b
Plane: when shutting down motors force outputs to minimum
...
this fixes issue #20354 where a long spool time can lead to motors
running without control for an extended period of time.
2022-03-28 20:53:56 +11:00
8b7366d619
Plane: adjust throttle mix for auto landing
...
use mix-max during landing approach and initial descent, use min in
land final. As discussed with Leonard
2022-03-18 14:24:46 +11:00
14571ee24b
Plane: added airspeed based pitch limit check
...
prevent using too much pitch when at low airspeed, which can lead to
severe instability in SLT quadplanes
2022-03-16 08:12:20 +11:00
d7052b4d5a
Plane: added an arming check for Q_ASSIST_SPEED
...
Q_ASSIST should really be enabled for all non-tailsitter
quadplanes. This arming check will help users remember to configure it
2022-03-16 07:09:30 +11:00
0bab0dc26c
Plane: use set_lean_angle_max_cd()
...
allows for a wider range of Q_TRANS_DECEL while landing on the desired
landing point
2022-03-16 07:09:30 +11:00
6839533e5d
Plane: improvements to POSITION1 controller
...
this improves 4 things in the POSITION1 controller based on logs from
4.2.0beta2. The changes are designed to increase the tolerance to
an incorrect value for Q_TRANS_DECEL, reducing landing overshoot
1) we fix the initialisation of the acceleration. The
init_xy_controller() function assumes zero accel, so we need to
call set_accel_desired_xy_cmss() just after that init to get the
correct accel. Thanks to Leonard for this fix
2) if we decel more than expected due to too low Q_TRANS_DECEL we
need to reduce the target speed, rather than putting the nose down
3) lower the default Q_P_JERK_XY to a value more appropriate for most
quadplanes (Leonard suggested a value of 2)
4) fixed the pitch envelope from Q_BACKTRANS_MS to start after the
airbrake phase is complete
2022-03-14 13:52:06 +11:00
965a571063
Plane: fixed pitch envelope after AIRBRAKE
...
we need to setup last_fw_mode_ms and last_fw_nav_pitch_cd when we
enter POSITION1 mode so that the expanding envelope pitch limit from
Q_BACKTRANS_MS is applied correctly
2022-03-14 11:06:29 +11:00
0aeb7e1500
Plane: protect against short stop_distance
2022-03-10 11:11:10 +11:00
8fd386f50b
Plane: quadplane: double log QPOS state change
2022-03-10 10:46:17 +11:00
9981a08791
Plane: use has_valid_input in place of checking throttle counter
2022-03-10 10:45:39 +11:00
1d2a64951c
Plane: use pos control for most of LAND_FINAL
...
this gives more accurate landing with some velocity drift
2022-03-10 07:36:30 +11:00
c4ce86a839
Plane: review fixes
...
thanks Pete!
2022-03-10 07:36:21 +11:00
c41a3af59d
Plane: wait till motors are fully up before takeoff in guided mode
...
this allows for guided mode takeoff in tilt-rotors. Otherwise motors
till be pointing forward and takeoff will go very badly
2022-03-10 07:36:08 +11:00
32404f5aa5
Plane: cope with high angle error in airbrake state
...
if we are flying too far off the target vector then exit airbrake
state. This prevents flying for a long distance away from the landing
point in airbrake mode
2022-03-10 07:36:05 +11:00
948ae05922
Plane: setup target accel in POSITION1 state
2022-03-10 07:36:01 +11:00
395cf1b6dd
Plane: allow for a trans decel margin
...
so if we are behind the velocity curve we are less likely to overshoot
landing
2022-03-10 07:35:58 +11:00
d0ce3c8774
Plane: fix NAV_CONTROLLER_OUTPUT in Q modes
...
Q modes don't always use wp_nav, but do use pos_control
AUTO and QRTL setup the plane navigation as well, so can use the L1
data
2022-03-10 07:35:32 +11:00
25f57af2e3
Plane: added APIs for lua ship landing
2022-03-10 07:35:29 +11:00
38662b98d8
Plane: added Q_LAND_ALTCHG parameter
...
this is the threshold height change over 4 seconds for a landing to be
detected. It can be raised if landing detection is very slow
2022-03-09 07:50:54 +11:00
267583db55
Plane: quadplane: never reset yaw target rates when entering QPOS1
2022-02-21 09:35:06 +11:00
9fd14dbf94
Plane: quadplane: set IO failsafe limit for all motors
2022-02-17 12:31:16 +11:00
1bdc9b5bf8
Plane: fixed in_vtol logic so QRTL can AIRBRAKE
2022-02-16 07:43:01 +11:00
aab6c94936
Plane: don't weathervane in AIRBRAKE state
...
this prevents unwanted VTOL motor throttle while trying to slow
down. In this stage the slaving of yaw rate to fixed wing roll control
is sufficient
2022-02-16 07:43:01 +11:00
2846f87eeb
Plane: reduce height gain in auto landing for tiltrotors
...
avoid running the motors while tilted past the tilt max if we are in
AIRBRAKE state. This stops a large amount of forward thrust from the
tilted motors while trying to slow down, while still maintaining
attitude control
2022-02-16 07:43:01 +11:00
1ca1707f9f
Plane: quadpalne: keep motors interlock state upto date with E-stop
2022-02-10 07:43:40 +09:00
717b18a680
Plane: quadplane: add allow_weathervane transtion class method
2022-02-08 10:38:16 +11:00
6a719664d3
Plane: quadplane: pass takeoff and landing state to weathervane
2022-02-08 10:38:16 +11:00
a79359dc67
Plane: use new weathervane library
2022-02-08 10:38:16 +11:00
f8383df5a4
Plane: Remove meaningless semicolons
2022-02-07 08:27:34 +09:00
54bdde8845
Copter: fix parameter issue with quadplane
2022-02-01 23:06:51 -05:00
266d384ca7
ArduPlane: rename AP_AHRS::get_position to get_location
2022-01-25 10:47:22 +11:00
32488a5e3a
Plane: add MOTB logging at 10hz
2022-01-18 10:18:10 +11:00
3a5c7ea8fc
Plane: quadplane: add transtion fail action param
2022-01-11 11:02:33 +11:00
2ffebebddc
Plane: tailsitter: provide min throttle limit based on disk therory outflow velocity
2022-01-11 10:37:38 +11:00
ca1b5b1db2
Plane: Quadplane: use get_frame_and_type_string
2022-01-05 19:51:19 +11:00
d4eb2c6396
Plane: quadplane: QPOS_POSITION1 tailsitters use input_vel_accel method
2022-01-04 10:42:12 +11:00
4848ac9166
Plane: quadplane: don't use `is_active_z()`, becasue its wrong
2022-01-04 10:42:12 +11:00
fb1f6b57ad
Plane: Quadplane: never run Z controller if motors are not throttle unlimited
2022-01-04 10:42:12 +11:00
c215fa0745
Plane: Quadplane: never run Z controller in tailsiter VTOL transtion
2022-01-04 10:42:12 +11:00
9df753551e
Plane: quadplane: tailsitter: always relax pitch after transtion
2022-01-04 10:42:12 +11:00
67d7ba490f
Plane: quadplane: pass time to tailsitter.in_vtol_transition where avalable
2022-01-04 10:42:12 +11:00
18e427d27d
Plane: add Q_OPTION to force fw trans on fail instead of QLAND
2021-12-24 13:55:15 +11:00
2154738421
Plane: Quadplane: only advance to QPOS_POSITION2 once tilts have finished slewing
2021-12-22 18:46:14 +11:00
eac52fe08f
Plane: quadplane: don't ouput VTOL throttle on tiltrotor with no VTOL motors and till fully forward
2021-12-22 18:46:14 +11:00
6116eaeb32
Plane: quadplane: enhance tiltrotor transtion to better deal with tiltrotors with all motors tilting
2021-12-22 18:46:14 +11:00
049f5f2135
Plane: fix divide by zero in transition time
2021-12-10 19:10:51 -08:00
e7c7cdd653
Plane: reset VTOL takeoff if not armed
...
we need to reset the takeoff target position while disarmed so we
don't use spurious position information from before we get good GPS
lock.
also remove the "Resetting previous waypoint" message as it doesn't
provide useful information and is just a distraction (it would be
printed continuously while waiting for arming with this PR)
2021-12-04 16:51:02 +11:00
52adda7c4c
Plane: INAV rename for neu & cm/cms
2021-11-30 10:08:07 +11:00
c6dd39773d
ArduPlane: inav use _xy()
2021-11-30 10:08:07 +11:00
Andrew Tridgell
Iampete1
Peter Barker
Gone4Dirt
murata
Bill Geyer
Hwurzburg
Josh Henderson