Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
4,155 Commits 71 Branches 509 Tags 718 MiB
Commit Graph

83 Commits

Author SHA1 Message Date
Andrew Tridgell 9d56d28615 MAVLink: make APM build with MAVLink 1.0 possible with arduino GUI 2012-04-24 22:24:58 +10:00
Andrew Tridgell 840f7f87ca ready for 2.33 release 2012-04-09 18:16:49 +10:00
Andrew Tridgell 222009002e MAVLink: allow for find grained stream rate control 
streams can now be requested at any multiple of 20ms. So if you ask
for a stream at 7Hz then you will get it at close to 7Hz.
 2012-04-02 11:18:53 +10:00
Andrew Tridgell 5dbd2a2b60 APM: enable AP_Declination by default 2012-03-30 14:25:27 +11:00
Andrew Tridgell eb98442ed0 APM: Change version to 2.32 2012-03-29 12:50:12 +11:00
Andrew Tridgell 491b73c4e2 APM: increase ArduPlane version to 2.31 2012-03-27 16:13:29 +11:00
Andrew Tridgell 3a325541f6 APM: enable the new offset nulling in APM 2012-03-27 15:37:24 +11:00
Andrew Tridgell c1e4f63907 APM: adapt ArduPlane for AHRS framework 2012-03-19 17:29:02 +11:00
Michael Oborne 80b356367e update AP version to 2.30 2012-03-18 10:27:49 +08:00
Andrew Tridgell 1e47ab26f2 AP_Declination: disable library when AUTOMATIC_DECLINATION is not ENABLED 
unfortunately this library was causing avrdude to fail to load the hex
to my APM2. Until we work out why, it's disabled.
 2012-03-11 21:46:41 +11:00
Adam M Rivera 2e1cacd67f AP_Declination: Added call to compass.set_initial_location if the compass is enabled when the 3D fix is obtained. 
Signed-off-by: Andrew Tridgell <tridge@samba.org>
 2012-03-11 20:59:47 +11:00
Andrew Tridgell 3239a00b23 APM: avoid fetching the DCM matrix twice 
also no special case for quaternions
 2012-03-10 10:34:32 +11:00
Andrew Tridgell aa4beb9753 APM: make it possible to build ArduPlane with quaternion support 2012-03-10 10:34:29 +11:00
rmackay9 630de04bd1 ArduPlane - updated to use new filter library 2012-02-28 21:03:04 +09:00
rmackay9 4501c488b4 ArduPlane - added Filter.h to unbreak the build! 2012-02-26 17:05:56 +09:00
rmackay9 6363da2829 ArduPlane - switch sonar to use new mode filter from filter library 2012-02-26 15:35:42 +09:00
Andrew Tridgell 3fe5b3151b allow MAG_ENABLE to be changed in flight 
this disables the compass in DCM if MAG_ENABLE is changed in
flight. Without this we would use a fixed yaw once the compass is
disabled

This also makes sure we don't pass the compass to DCM till we have
done a read. This ensures we have a good compass fix for the initial
DCM heading
 2012-02-25 14:51:09 +11:00
Andrew Tridgell 252a2d0c9b APM: added some comments related to hold_course 
hold_course is either -1 (for disabled) or a course to hold for
takeoff/landing. This makes the code a bit clearer.

It also resets hold_course in all non-auto modes, to ensure it isn't
used
 2012-02-15 08:50:45 +11:00
Andrew Tridgell faa098b2b6 adapt mainline APM code to AP_Param 2012-02-13 16:22:51 +11:00
Michael Oborne 9dafc668cd fix SITL attitude hil 2012-01-20 16:04:49 +08:00
analoguedevices 40f37c1037 Increment version number in anticipation of a firmware hex push. 2012-01-16 22:48:46 +00:00
Doug Weibel 78ac65d6c3 Additional commenting on global variables 
First pass done.
 2012-01-16 10:28:03 -07:00
Doug Weibel a3f9fee3d2 Additional commenting on global variables 2012-01-16 09:45:42 -07:00
Doug Weibel 17b3e514dc Just a little more commenting work on global variables 2012-01-15 16:11:02 -07:00
Doug Weibel fd8dc84fac Update battery monitoring code for ArduPlane 
Fixes compatibility for APM2.  Also a significant update to the battery monitoring code:  We previously had monitoring modes for individual cell voltages for 3 and 4 cell lipos.  These have been removed as they were never really supported (the cell voltages were computed but were not reported or recorded anywhere).  Also, some clean-up/prep work was done for supporting monitoring 2 separate battery packs.  The CLI battery and current monitoring tests were consolidated into 1 test.
 2012-01-15 16:10:28 -07:00
Doug Weibel 6f9c6a3b8e Adding comments for global variables 2012-01-11 12:37:43 -07:00
Doug Weibel 35fba5d4a3 Tweak to FBW min altitude 
Patch from Yury
 2011-12-31 15:44:40 -07:00
Andrew Tridgell 5aca951438 APM: added error checking on barometer read 
if the barometer is dead and the GPS has a fix, use the GPS for
altitude
 2011-12-28 20:41:53 +11:00
Andrew Tridgell 2c41264a9b APM: added error checking on compass read 2011-12-28 20:41:53 +11:00
Andrew Tridgell c6b8a08918 APM: convert to new I2C library 2011-12-28 20:41:53 +11:00
analoguedevices fefda548d2 Added contributor names, removed "alpha" from firmware name 2011-12-26 17:13:37 +00:00
Andrew Tridgell 0aab4da1a1 mainloop_count should be uint16_t 2011-12-21 23:31:38 +11:00
Andrew Tridgell 61b2b2e32a always declare a timer_scheduler 
we should always run this code
 2011-12-21 23:31:38 +11:00
Andrew Tridgell 5d2301ef47 fixed airspeed sensor for ArduPlane on APM2 
we were trying to use a non-existant ADC chip!
 2011-12-17 07:29:09 +11:00
Andrew Tridgell 4bbd5392ef removed AperiodicProcess code 
this code was never being used, and was more complex than it was
worth.
 2011-12-17 07:29:09 +11:00
Andrew Tridgell b3327c64de geofence: added fence status reporting and faster altitude check 2011-12-16 20:11:51 +11:00
Andrew Tridgell 1b64185b18 geofence: main geo-fence code 
this implements the primary logic of geo-fencing
 2011-12-16 20:11:51 +11:00
Andrew Tridgell 1455ff4a91 removed an unused variable 2011-12-16 20:09:49 +11:00
Andrew Tridgell 4e4a4a685c fixed two more CONFIG_HARDWARE #ifdef bugs 2011-12-13 17:05:48 +11:00
Andrew Tridgell 80a0dfe862 fixed hardware config check for barometer 2011-12-12 15:14:55 +11:00
Andrew Tridgell faf58a355b airspeed: use floating point values and better averaging in zero_airspeed() 
this makes the calibration of airspeed a bit more accurate, and
prevents truncation of airspeed values
 2011-12-12 15:14:55 +11:00
Pat Hickey 85b82e75f6 ArduPlane: update AP_Baro construtors and initializers 2011-12-11 15:21:10 -08:00
Pat Hickey 63d3b6a278 ArduPlane: Rename APM_BMP085 classes to AP_Baro_BMP085 classes 2011-12-11 15:21:09 -08:00
Doug Weibel f34333d42b Minimum ground speed patch from Claudio Natoli. Thanks Claudio! 
This patch will boost the target airspeed as necessary to keep the ground speed above a parameter value - param_min_groundspeed.  Airspeed is still limited to FBW-max.  Setting min_groundspeed to zero (default) disables the feature.
 2011-12-09 16:43:25 -07:00
Pat Hickey 0fa8ce9a52 ArduPlane: rev version number from 2.26 to 2.27 Alpha 2011-11-25 20:00:19 -08:00
Andrew Tridgell 7467bf649c ArduPlane: rename purple to APM2 2011-11-25 20:00:19 -08:00
Andrew Tridgell 0604f2c667 USB-MUX: auto-switch telemetry port based on UXB mux for ArduPlane 
when USB is unplugged, switch baud rate to the SERIAL3_BAUD rate from
EEPROM
 2011-11-25 20:00:19 -08:00
Andrew Tridgell 2bed1dcfd5 desktop: first version of register level SITL support 
this adds register level emulation of the ADS7844 and the RC
input/output hardware on the APM1, allowing for SITL testing without
enabling HIL in the code
 2011-11-25 20:00:18 -08:00
Andrew Tridgell 446a9aac84 re-organiser sensor declarations 
this tries to make the #ifdef nesting easier to understand
 2011-11-25 20:00:17 -08:00
Andrew Tridgell 992fc87112 purple: always declare timer_scheduler 2011-11-25 20:00:17 -08:00