mirror of https://github.com/ArduPilot/ardupilot
AP_HAL_ChibiOS: remove erroneous FlywooF745v2
This commit is contained in:
Andy Piper
Andrew Tridgell
parent
74c790cfc2
commit
d5535cc0cf
Binary file not shown.
|
Before Width: | Height: | Size: 8.2 MiB |
|
|
@ -1,109 +0,0 @@
|
|||
# Flywoo GOKU GN 745 40A AIO
|
||||
|
||||
https://flywoo.net/products/goku-gn745-40a-aio-bl_32-mpu6000-25-5-x-25-5
|
||||
|
||||
The Flywoo GOKU GN 745 AIO is a flight controller produced by [Flywoo](https://flywoo.net/).
|
||||
|
||||
## Features
|
||||
|
||||
- MCU: STM32F745 32-bit processor,216MHz, 512Kbytes Flash
|
||||
- IMU: MPU6000 (SPI)
|
||||
- Barometer: SPL06
|
||||
- Onboard LED：WS2812*4
|
||||
- USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
|
||||
- 7 hardware UARTS (UART1,2,3,4,5,6,7)
|
||||
- Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only.
|
||||
- PPM and PWM receivers are not supported.
|
||||
- Onbord 8Mbytes for Blackbox logging
|
||||
- 9V Power Out: 1.5A max
|
||||
- 5V Power Out: 2.0A max
|
||||
- 3.3V Power Out: 0.5A max
|
||||
- Dimensions: 33.5x33.5mm
|
||||
- Mounting Holes: Standard 25.5/26.5mm square to center of holes
|
||||
- Weight: 8.5g
|
||||
|
||||
- Built-in 40A BL_32 4in1 ESC
|
||||
- Support BLheli / BLHELI_32
|
||||
- Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600,Dshot1200
|
||||
- Input Voltage: 2-6S Lipo
|
||||
- Continuous Current: 40A
|
||||
- Firmware: BLHELI_32
|
||||
|
||||
## Pinout
|
||||
|
||||
|
||||
|
||||
## UART Mapping
|
||||
|
||||
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the
|
||||
receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
|
||||
|Name|Pin|Function|
|
||||
|:-|:-|:-|
|
||||
|SERIAL0|COMPUTER|USB|
|
||||
|SERIAL1|RX1/TX1|UART1 (TELEM)|
|
||||
|SERIAL2|TX2/RX2|UART2 (TELEM)|
|
||||
|SERIAL3|TX3/RX3|UART3 (RC Input/Output)|
|
||||
|SERIAL4|TX4/RX4|UART4|
|
||||
|SERIAL5|TX5/RX5|UART5|
|
||||
|SERIAL6|TX6/RX6|UART6 (GPS)|
|
||||
|SERIAL7|TX7/RX7|UART7|
|
||||
|
||||
UART3 supports RX and TX DMA. UART1, UART2, UART4, and UART6 supports TX DMA. UART5 and UART7 do not support DMA.
|
||||
|
||||
## RC Input
|
||||
|
||||
RC input is configured on the UART3, which supports serial RC protocols. This board does not support PPM.
|
||||
|
||||
## OSD Support
|
||||
|
||||
The GOKU GN 745 AIO supports OSD using OSD_TYPE 1 (MAX7456 driver).
|
||||
|
||||
## PWM Output
|
||||
|
||||
The GOKU GN 745 AIO supports up to 8 PWM outputs. The pads for motor output ESC1 to ESC4 on the above diagram are the first 4 outputs, there are four additional pads for PWM 5-8. All 8 outputs support DShot as well as all PWM types.
|
||||
|
||||
The PWM are in 5 groups:
|
||||
|
||||
PWM 1,3,7,8: Group 1
|
||||
PWM 2: Group 2
|
||||
PWM 4-5: Group 3
|
||||
PWM 6: Group 4
|
||||
LED: Group 5
|
||||
|
||||
|
||||
Channels within the same group need to use the same output rate. If
|
||||
any channel in a group uses DShot then all channels in the group need
|
||||
to use DShot. PWM 1-4 support bidirectional dshot.
|
||||
|
||||
## Battery Monitoring
|
||||
|
||||
The board has a builtin voltage sensor. The voltage sensor can handle 2S to 6S
|
||||
LiPo batteries.
|
||||
|
||||
The correct battery setting parameters are:
|
||||
|
||||
- BATT_MONITOR 4
|
||||
- BATT_VOLT_PIN 12
|
||||
- BATT_VOLT_MULT around 10.9
|
||||
- BATT_CURR_PIN 13
|
||||
- BATT_CURR_MULT around 62.0
|
||||
|
||||
These are set by default in the firmware and shouldn't need to be adjusted
|
||||
|
||||
## Compass
|
||||
|
||||
The GOKU GN 745 AIO does not have a builtin compass but it does have an external I2C connector.
|
||||
|
||||
## NeoPixel LED
|
||||
|
||||
The board includes a NeoPixel LED pad.
|
||||
|
||||
## Loading Firmware (you will need to compile your own firmware)
|
||||
|
||||
Initial firmware load can be done with DFU by plugging in USB with the
|
||||
bootloader button pressed. Then you should load the "with_bl.hex"
|
||||
firmware, using your favourite DFU loading tool.
|
||||
|
||||
Once the initial firmware is loaded you can update the firmware using
|
||||
any ArduPilot ground station software. Updates should be done with the
|
||||
*.apj firmware files.
|
||||
|
|
@ -1,13 +0,0 @@
|
|||
# setup the four built-in Neopixel LEDs on chan 9
|
||||
SERVO9_FUNCTION 120
|
||||
NTF_LED_TYPES 257
|
||||
NTF_LED_LEN 4
|
||||
|
||||
# setup SERIAL3 for RCIN
|
||||
SERIAL3_PROTOCOL 23
|
||||
|
||||
# disable GPS on Serial 4
|
||||
SERIAL4_PROTOCOL -1
|
||||
|
||||
# setup SERIAL6 for GPS
|
||||
SERIAL6_PROTOCOL 5
|
||||
|
|
@ -1 +0,0 @@
|
|||
include ../FlywooF745/hwdef-bl.dat
|
||||
|
|
@ -1,21 +0,0 @@
|
|||
# hw definition file for processing by chibios_pins.py
|
||||
# for FLYWOO Goku GN F745 v2
|
||||
# thanks to betaflight for pin information
|
||||
|
||||
include ../FlywooF745/hwdef.dat
|
||||
|
||||
undef PB1 PB0 PE9 PE11 PC9 PA3 PB4 PB5
|
||||
|
||||
# MOTORS
|
||||
PB1 TIM3_CH4 TIM3 PWM(1) GPIO(50) BIDIR # M1
|
||||
PC9 TIM8_CH4 TIM8 PWM(2) GPIO(51) BIDIR # M2
|
||||
PB0 TIM3_CH3 TIM3 PWM(3) GPIO(52) # M3
|
||||
PE11 TIM1_CH2 TIM1 PWM(4) GPIO(53) BIDIR # M4
|
||||
PE9 TIM1_CH1 TIM1 PWM(5) GPIO(54) # M5
|
||||
PA3 TIM5_CH4 TIM5 PWM(6) GPIO(55) # M6
|
||||
PB4 TIM3_CH1 TIM3 PWM(7) GPIO(56) # M7
|
||||
PB5 TIM3_CH2 TIM3 PWM(8) GPIO(57) # M8
|
||||
|
||||
undef HAL_BATT_CURR_SCALE
|
||||
define HAL_BATT_CURR_SCALE 62.0
|
||||
|
||||
Loading…
Reference in New Issue