2024-01-24 22:45:15 -04:00
|
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
|
# for the BotBloxSwitch hardware
|
|
|
|
|
|
|
|
|
|
# default to all pins low to avoid ESD issues
|
|
|
|
|
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32H7xx STM32H723xx
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 0
|
|
|
|
|
|
|
|
|
|
# setup build for a peripheral bootloader
|
|
|
|
|
env AP_PERIPH 1
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID AP_HW_BotBloxSwitch
|
|
|
|
|
|
|
|
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 32768
|
|
|
|
|
|
|
|
|
|
# use last 2 pages for flash storage
|
|
|
|
|
# H723 has 8 pages of 128k each
|
|
|
|
|
STORAGE_FLASH_PAGE 6
|
|
|
|
|
|
|
|
|
|
# flash size
|
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
|
|
|
|
|
|
env OPTIMIZE -Os
|
|
|
|
|
|
|
|
|
|
# pins for SWD debugging
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# USB
|
|
|
|
|
PA11 OTG_HS_DM OTG1
|
|
|
|
|
PA12 OTG_HS_DP OTG1
|
|
|
|
|
PA9 VBUS INPUT OPENDRAIN
|
|
|
|
|
|
|
|
|
|
# CAN bus
|
|
|
|
|
PD0 CAN1_RX CAN1
|
|
|
|
|
PD1 CAN1_TX CAN1
|
|
|
|
|
|
|
|
|
|
PD8 USART3_TX USART3
|
|
|
|
|
PD9 USART3_RX USART3
|
|
|
|
|
PD12 USART3_RTS USART3
|
|
|
|
|
PD11 USART3_CTS USART3
|
|
|
|
|
|
|
|
|
|
# LEDs
|
|
|
|
|
PE3 LED_RED OUTPUT OPENDRAIN HIGH
|
|
|
|
|
PE4 LED_GREEN OUTPUT OPENDRAIN HIGH
|
|
|
|
|
PE5 LED_BLUE OUTPUT OPENDRAIN HIGH
|
|
|
|
|
define HAL_LED_ON 0
|
|
|
|
|
|
|
|
|
|
# use blue LED
|
|
|
|
|
define HAL_GPIO_PIN_LED HAL_GPIO_PIN_LED_BLUE
|
|
|
|
|
|
|
|
|
|
PC1 ETH_MDC ETH1
|
|
|
|
|
PA2 ETH_MDIO ETH1
|
|
|
|
|
PC4 ETH_RMII_RXD0 ETH1
|
|
|
|
|
PC5 ETH_RMII_RXD1 ETH1
|
|
|
|
|
#PB12 ETH_RMII_TXD0 ETH1
|
|
|
|
|
PG13 ETH_RMII_TXD0 ETH1
|
|
|
|
|
PB13 ETH_RMII_TXD1 ETH1
|
|
|
|
|
#PB11 ETH_RMII_TX_EN ETH1
|
|
|
|
|
PG11 ETH_RMII_TX_EN ETH1
|
|
|
|
|
PA7 ETH_RMII_CRS_DV ETH1
|
|
|
|
|
PA1 ETH_RMII_REF_CLK ETH1
|
|
|
|
|
|
|
|
|
|
define BOARD_PHY_ID MII_LAN8742A_ID
|
|
|
|
|
define BOARD_PHY_RMII
|
|
|
|
|
|
|
|
|
|
include ../include/network_PPPGW.inc
|
|
|
|
|
|
|
|
|
|
# allow load from USB
|
|
|
|
|
SERIAL_ORDER OTG1 USART3
|
|
|
|
|
|
|
|
|
|
# no ADC pins
|
|
|
|
|
define HAL_USE_ADC FALSE
|
|
|
|
|
|
|
|
|
|
define STM32_ADC_USE_ADC1 FALSE
|
|
|
|
|
define STM32_ADC_USE_ADC2 FALSE
|
|
|
|
|
define STM32_ADC_USE_ADC3 FALSE
|
|
|
|
|
|
2024-04-01 03:38:32 -03:00
|
|
|
define HAL_RCIN_THREAD_ENABLED 1
|
2024-04-01 19:47:40 -03:00
|
|
|
define HAL_SCHEDULER_LOOP_DELAY_ENABLED 1
|
