mirror of https://github.com/ArduPilot/ardupilot
85 lines
2.3 KiB
Markdown
85 lines
2.3 KiB
Markdown
|
# Mamba F405 MK2 Flight Controller
|
||
|
|
|
||
|
|
https://www.diatone.us/products/mamba-f405-flight-controller-mk2
|
||
|
|
|
||
|
|
The Mamba F405 MK2 is a flight controller produced by [Diatone](https://www.diatone.us).
|
||
|
|
|
||
|
|
## Features
|
||
|
|
|
||
|
|
- STM32F405RGT6 microcontroller
|
||
|
|
- MPU6000 IMU
|
||
|
|
- AT7456E OSD
|
||
|
|
- 4 UARTs
|
||
|
|
- 4 PWM outputs
|
||
|
|
|
||
|
|
## Pinout
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
## UART Mapping
|
||
|
|
|
||
|
|
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the
|
||
|
|
receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
|
||
|
|
|Name|Pin|Function|
|
||
|
|
|:-|:-|:-|
|
||
|
|
|SERIAL0|COMPUTER|USB|
|
||
|
|
|SERIAL1|PPM/RX1/SBUS/TX1|UART1 (RC Input)|
|
||
|
|
|SERIAL3|TX3/RX3|UART3 (Telem1)|
|
||
|
|
|SERIAL6|TX6/RX6|UART6 (GPS)|
|
||
|
|
|
||
|
|
|
||
|
|
## RC Input
|
||
|
|
|
||
|
|
RC input is configured on the PPM (UART1_RX) pin. It supports all RC protocols.
|
||
|
|
The S.BUS pad provides an inverted input for S.BUS receivers.
|
||
|
|
|
||
|
|
## OSD Support
|
||
|
|
|
||
|
|
The Mamba F405 MK2 supports OSD using OSD_TYPE 1 (MAX7456 driver).
|
||
|
|
|
||
|
|
## PWM Output
|
||
|
|
|
||
|
|
The Mamba F405 MK2 supports up to 4 PWM outputs. The pads for motor output ESC1 to ESC4 on the above diagram are for the 4 outputs. All 4 outputs support DShot as well as all PWM types.
|
||
|
|
|
||
|
|
The PWM are in one group.
|
||
|
|
|
||
|
|
Channels within the same group need to use the same output rate. If
|
||
|
|
any channel in a group uses DShot then all channels in the group need
|
||
|
|
to use DShot.
|
||
|
|
|
||
|
|
## Battery Monitoring
|
||
|
|
|
||
|
|
The board has a builting voltage sensor. The voltage sensor can handle up to 6S
|
||
|
|
LiPo batteries.
|
||
|
|
|
||
|
|
The correct battery setting parameters are:
|
||
|
|
|
||
|
|
- BATT_MONITOR 3
|
||
|
|
- BATT_VOLT_PIN 11
|
||
|
|
- BATT_VOLT_MULT around 12.0
|
||
|
|
- BATT_CURR_PIN 13
|
||
|
|
- BATT_CURR_MULT around 39 with the included 40A ESC
|
||
|
|
|
||
|
|
## Compass
|
||
|
|
|
||
|
|
The Mamba F405 MK2 does not have a builting compass, but you can attach an external compass using I2C on the SDA and SCL pads.
|
||
|
|
|
||
|
|
## Alternate settings
|
||
|
|
|
||
|
|
It is possible to set alternate configurations with the BRD_ALT_CONFIG parameter.
|
||
|
|
|
||
|
|
|BRD_ALT_CONFIG|RX1 function|
|
||
|
|
|:----|:----|
|
||
|
|
|ALT 0(default) |RCININT|
|
||
|
|
|ALT 1|RX1/TX1|
|
||
|
|
|
||
|
|
## Loading Firmware
|
||
|
|
|
||
|
|
Initial firmware load can be done with DFU by plugging in USB with the
|
||
|
|
bootloader button pressed. Then you should load the "with_bl.hex"
|
||
|
|
firmware, using your favourite DFU loading tool.
|
||
|
|
|
||
|
|
Once the initial firmware is loaded you can update the firmware using
|
||
|
|
any ArduPilot ground station software. Updates should be done with the
|
||
|
|
*.apj firmware files.
|