mirror of https://github.com/ArduPilot/ardupilot
124 lines
3.3 KiB
Markdown
124 lines
3.3 KiB
Markdown
|
# JFB-100 Flight Controller
|
||
|
|
|
||
|
|
The JFB-100 flight controller is sold by [JAE](https://www.jae.com/files/user/motion-sense-control/catalog/jfb-100-ja.pdf)
|
||
|
|
|
||
|
|
## Features
|
||
|
|
|
||
|
|
- STM32F765 microcontroller
|
||
|
|
- Two IMUs: ICM20602 and SCHA63T
|
||
|
|
- MS5611 SPI barometer
|
||
|
|
- builtin I2C IST8310 magnetometer
|
||
|
|
- microSD card slot
|
||
|
|
- 6 UARTs plus USB
|
||
|
|
- 8 PWM outputs
|
||
|
|
- Four I2C and two CAN ports
|
||
|
|
- External Buzzer
|
||
|
|
- external safety Switch
|
||
|
|
- voltage monitoring for servo rail and Vcc
|
||
|
|
- two dedicated power input ports for external power bricks
|
||
|
|
|
||
|
|
## UART Mapping
|
||
|
|
|
||
|
|
- SERIAL0 -> USB
|
||
|
|
- SERIAL1 -> UART2 (Telem1)
|
||
|
|
- SERIAL2 -> UART3 (Telem2)
|
||
|
|
- SERIAL3 -> UART1 (GPS)
|
||
|
|
- SERIAL4 -> UART4 (GPS2, marked UART/I2CB)
|
||
|
|
- SERIAL5 -> UART6 (RC)
|
||
|
|
- SERIAL6 -> UART7 (spare, debug)
|
||
|
|
|
||
|
|
The Telem1 and Telem2 ports have RTS/CTS pins, the other UARTs do not
|
||
|
|
have RTS/CTS.
|
||
|
|
|
||
|
|
The UART7 connector is labelled debug, but is available as a general
|
||
|
|
purpose UART with ArduPilot.
|
||
|
|
|
||
|
|
## RC Input
|
||
|
|
|
||
|
|
RC input is configured on the port marked DSM/SBUS RC. This connector
|
||
|
|
supports all RC protocols. Two cables are available for this port. To
|
||
|
|
use software binding of Spektrum satellite receivers you need to use
|
||
|
|
the Spektrum satellite cable.
|
||
|
|
|
||
|
|
## PWM Output
|
||
|
|
|
||
|
|
The JFB-100 supports up to 8 PWM outputs.
|
||
|
|
These are directly attached to the STM32F765 and support all
|
||
|
|
PWM protocols. The first 4 of the PWM outputs support DShot.
|
||
|
|
|
||
|
|
The 8 PWM outputs are in 3 groups:
|
||
|
|
|
||
|
|
- PWM 1, 2, 3 and 4 in group1
|
||
|
|
- PWM 5 and 6 in group2
|
||
|
|
- PWM 7 and 8 in group3
|
||
|
|
|
||
|
|
Channels within the same group need to use the same output rate. If
|
||
|
|
any channel in a group uses DShot then all channels in the group need
|
||
|
|
to use DShot.
|
||
|
|
|
||
|
|
## Battery Monitoring
|
||
|
|
|
||
|
|
The board has two dedicated power monitor ports on 8 pin
|
||
|
|
connectors. The correct battery setting parameters are dependent on
|
||
|
|
the type of power brick which is connected.
|
||
|
|
|
||
|
|
## Compass
|
||
|
|
|
||
|
|
The JFB-100 has a builtin IST8310 compass. Due to potential
|
||
|
|
interference the board is usually used with an external I2C compass as
|
||
|
|
part of a GPS/Compass combination.
|
||
|
|
|
||
|
|
## GPIOs
|
||
|
|
|
||
|
|
The 6 PWM ports can be used as GPIOs (relays, buttons, RPM etc). To
|
||
|
|
use them you need to limit the number of these pins that is used for
|
||
|
|
PWM by setting the BRD_PWM_COUNT to a number less than 6. For example
|
||
|
|
if you set BRD_PWM_COUNT to 4 then PWM5 and PWM6 will be available for
|
||
|
|
use as GPIOs.
|
||
|
|
|
||
|
|
The numbering of the GPIOs for PIN variables in ArduPilot is:
|
||
|
|
|
||
|
|
- AUX1 50
|
||
|
|
- AUX2 51
|
||
|
|
- AUX3 52
|
||
|
|
- AUX4 53
|
||
|
|
- AUX5 54
|
||
|
|
- AUX6 55
|
||
|
|
|
||
|
|
## Analog inputs
|
||
|
|
|
||
|
|
The JFB-100 has 7 analog inputs
|
||
|
|
|
||
|
|
- ADC Pin0 -> Battery Voltage
|
||
|
|
- ADC Pin1 -> Battery Current Sensor
|
||
|
|
- ADC Pin2 -> Battery Voltage 2
|
||
|
|
- ADC Pin3 -> Battery Current Sensor 2
|
||
|
|
- ADC Pin4 -> ADC port pin 2
|
||
|
|
- ADC Pin14 -> ADC port pin 3
|
||
|
|
- ADC Pin10 -> ADC 5V Sense
|
||
|
|
- ADC Pin11 -> ADC 3.3V Sense
|
||
|
|
- ADC Pin103 -> RSSI voltage monitoring
|
||
|
|
|
||
|
|
## I2C Buses
|
||
|
|
|
||
|
|
- the internal I2C port is bus 0 in ArduPilot (I2C3 in hardware)
|
||
|
|
- the port labelled I2CA is bus 3 in ArduPilot (I2C4 in hardware)
|
||
|
|
- the port labelled I2CB is bus 2 in ArduPilot (I2c2 in hardware)
|
||
|
|
- the port labelled GPS is bus 1 in ArduPilot (I2c1 in hardware)
|
||
|
|
|
||
|
|
|
||
|
|
## CAN
|
||
|
|
|
||
|
|
The JFB-100 has two independent CAN buses, with the following pinouts.
|
||
|
|
|
||
|
|
## Debug
|
||
|
|
|
||
|
|
The JFB-100 supports SWD debugging on the debug port
|
||
|
|
|
||
|
|
|
||
|
|
## Loading Firmware
|
||
|
|
|
||
|
|
The board comes pre-installed with an ArduPilot compatible bootloader,
|
||
|
|
allowing the loading of *.apj firmware files with any ArduPilot
|
||
|
|
compatible ground station.
|