2022-09-04 08:41:44 -03:00
|
|
|
# hw definition file for AtomRC F405 hardware
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 1078
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
|
|
|
|
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
|
|
|
|
|
|
# only one I2C bus
|
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
|
|
|
|
|
|
# order of UARTs (and USB)
|
|
|
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 UART5 USART6
|
|
|
|
|
|
|
|
|
|
# LEDs
|
|
|
|
|
PA14 LED_BLUE OUTPUT LOW GPIO(0)
|
|
|
|
|
PA13 LED_GREEN OUTPUT LOW GPIO(1)
|
|
|
|
|
|
2024-07-09 00:19:56 -03:00
|
|
|
define AP_NOTIFY_GPIO_LED_2_ENABLED 1
|
2022-09-04 08:41:44 -03:00
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
|
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
|
|
|
|
|
|
|
|
# buzzer
|
|
|
|
|
PC5 BUZZER OUTPUT GPIO(80) LOW
|
|
|
|
|
define HAL_BUZZER_PIN 80
|
2023-04-22 18:11:08 -03:00
|
|
|
|
2023-04-21 10:26:50 -03:00
|
|
|
|
2022-09-04 08:41:44 -03:00
|
|
|
|
|
|
|
|
# spi1 bus for IMU
|
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
|
PA4 IMU_CS CS
|
|
|
|
|
|
|
|
|
|
# spi2 for OSD
|
|
|
|
|
PB13 SPI2_SCK SPI2
|
|
|
|
|
PB14 SPI2_MISO SPI2
|
|
|
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
|
PB12 AT7456E_CS CS
|
|
|
|
|
|
|
|
|
|
# spi3 for sdcard
|
|
|
|
|
PB3 SPI3_SCK SPI3
|
|
|
|
|
PB4 SPI3_MISO SPI3
|
|
|
|
|
PB5 SPI3_MOSI SPI3
|
|
|
|
|
PB6 SDCARD_CS CS
|
|
|
|
|
|
|
|
|
|
# one I2C bus
|
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
|
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
|
|
|
|
|
|
# analog pins
|
|
|
|
|
PC2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
PC0 RSSI_ADC_PIN ADC1 SCALE(1)
|
|
|
|
|
PC3 AIRSPEED_ADC ADC1 SCALE(1)
|
|
|
|
|
|
|
|
|
|
define HAL_DEFAULT_AIRSPEED_PIN 13
|
|
|
|
|
|
|
|
|
|
# define default battery setup
|
|
|
|
|
define HAL_BATT_VOLT_PIN 12
|
|
|
|
|
define HAL_BATT_CURR_PIN 11
|
|
|
|
|
define HAL_BATT_VOLT_SCALE 11.08836
|
|
|
|
|
define HAL_BATT_CURR_SCALE 30.0
|
|
|
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
|
|
|
|
|
|
|
|
# analog rssi pin
|
|
|
|
|
define BOARD_RSSI_ANA_PIN 10
|
|
|
|
|
|
|
|
|
|
# USART1
|
|
|
|
|
PA9 USART1_TX USART1
|
|
|
|
|
PA10 USART1_RX USART1
|
|
|
|
|
|
|
|
|
|
# USART2 - RCIN with inverter
|
|
|
|
|
PA2 USART2_TX USART2
|
|
|
|
|
PA3 TIM9_CH2 TIM9 RCININT PULLDOWN
|
|
|
|
|
|
|
|
|
|
# alternative with PA3 as USART2_RX
|
|
|
|
|
PA3 USART2_RX USART2 NODMA ALT(1)
|
|
|
|
|
|
|
|
|
|
# USART3
|
|
|
|
|
PC10 USART3_TX USART3
|
|
|
|
|
PC11 USART3_RX USART3
|
2023-05-03 21:30:51 -03:00
|
|
|
define DEFAULT_SERIAL3_PROTOCOL 0
|
2022-09-04 08:41:44 -03:00
|
|
|
|
|
|
|
|
# UART4 GPS
|
|
|
|
|
PA0 UART4_TX UART4 NODMA
|
|
|
|
|
PA1 UART4_RX UART4 NODMA
|
2023-05-03 21:30:51 -03:00
|
|
|
define DEFAULT_SERIAL4_PROTOCOL 5
|
2022-09-04 08:41:44 -03:00
|
|
|
|
|
|
|
|
# UART5 for DJI OSD
|
|
|
|
|
PD2 UART5_RX UART5 NODMA
|
|
|
|
|
PC12 UART5_TX UART5 NODMA
|
|
|
|
|
|
|
|
|
|
# USART6
|
|
|
|
|
PC6 USART6_TX USART6
|
|
|
|
|
PC7 USART6_RX USART6
|
|
|
|
|
|
|
|
|
|
# USB
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
# debug (disabled out to allow for both LEDs)
|
|
|
|
|
#PA13 JTMS-SWDIO SWD
|
|
|
|
|
#PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# PWM out pins. Note that channel order follows the ArduPilot motor
|
|
|
|
|
# order conventions
|
|
|
|
|
PC8 TIM3_CH3 TIM3 PWM(1) GPIO(50)
|
|
|
|
|
PC9 TIM3_CH4 TIM3 PWM(2) GPIO(51)
|
|
|
|
|
PA8 TIM1_CH1 TIM1 PWM(3) GPIO(52)
|
2023-10-15 10:19:04 -03:00
|
|
|
PB1 TIM8_CH3N TIM8 PWM(4) GPIO(53)
|
2022-09-04 08:41:44 -03:00
|
|
|
PA15 TIM2_CH1 TIM2 PWM(5) GPIO(54)
|
|
|
|
|
PB10 TIM2_CH3 TIM2 PWM(6) GPIO(55)
|
|
|
|
|
PB11 TIM2_CH4 TIM2 PWM(7) GPIO(56)
|
2023-10-15 10:19:04 -03:00
|
|
|
PB0 TIM8_CH2N TIM8 PWM(8) GPIO(57)
|
2022-09-04 08:41:44 -03:00
|
|
|
PB7 TIM4_CH2 TIM4 PWM(9) GPIO(58) # LED strip
|
|
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 15360
|
|
|
|
|
STORAGE_FLASH_PAGE 2
|
|
|
|
|
|
|
|
|
|
# reserve 32k for bootloader and 32k for flash storage
|
|
|
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
|
|
|
|
|
|
# one IMU
|
|
|
|
|
IMU BMI270 SPI:bmi270 ROTATION_PITCH_180
|
|
|
|
|
|
|
|
|
|
# I2C BMP280 or SPL06
|
|
|
|
|
BARO SPL06 I2C:0:0x76
|
|
|
|
|
BARO BMP280 I2C:0:0x76
|
|
|
|
|
|
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
|
|
|
# external compass types
|
|
|
|
|
define ALLOW_ARM_NO_COMPASS
|
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
|
|
|
|
|
|
# SPI devices
|
|
|
|
|
SPIDEV bmi270 SPI1 DEVID1 IMU_CS MODE3 1*MHZ 10*MHZ
|
|
|
|
|
SPIDEV sdcard SPI3 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
|
|
|
SPIDEV osd SPI2 DEVID1 AT7456E_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
|
|
|
|
|
|
# filesystem setup on sdcard
|
|
|
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
|
|
|
|
|
|
# setup for OSD
|
|
|
|
|
define OSD_ENABLED 1
|
|
|
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
|
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font0.bin
|
|
|
|
|
|
|
|
|
|
# reduce max size of embedded params for apj_tool.py
|
|
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 256
|
|
|
|
|
|
|
|
|
|
# save some flash
|
2023-10-15 10:19:04 -03:00
|
|
|
include ../include/minimize_fpv_osd.inc
|
|
|
|
|
|
2022-09-04 08:41:44 -03:00
|
|
|
define HAL_PARACHUTE_ENABLED 0
|
2023-10-15 10:19:04 -03:00
|
|
|
|
|
|
|
|
|
