ardupilot/ArduCopter/events.pde

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-

/*
 *       This event will be called when the failsafe changes
 *       boolean failsafe reflects the current state
 */
static void failsafe_on_event()
{
    // if motors are not armed there is nothing to do
    if( !motors.armed() ) {
        return;
    }

    // This is how to handle a failsafe.
    switch(control_mode) {
        case STABILIZE:
        case ACRO:
            // if throttle is zero disarm motors
            if (g.rc_3.control_in == 0) {
                init_disarm_motors();
            }else if(ap.home_is_set == true && home_distance > g.waypoint_radius) {
                set_mode(RTL);
            }else{
                // We have no GPS or are very close to home so we will land
                set_mode(LAND);
            }
            break;
        case AUTO:
            // failsafe_throttle is 1 do RTL, 2 means continue with the mission
            if (g.failsafe_throttle == FS_THR_ENABLED_ALWAYS_RTL) {
                if(home_distance > g.waypoint_radius) {
                    set_mode(RTL);
                }else{
                    // We are very close to home so we will land
                    set_mode(LAND);
                }
            }
            // if failsafe_throttle is 2 (i.e. FS_THR_ENABLED_CONTINUE_MISSION) no need to do anything
            break;
        default:
            if(ap.home_is_set == true && home_distance > g.waypoint_radius) {
                set_mode(RTL);
            }else{
                // We have no GPS or are very close to home so we will land
                set_mode(LAND);
            }
            break;
    }

    // log the error to the dataflash
    Log_Write_Error(ERROR_SUBSYSTEM_FAILSAFE, ERROR_CODE_FAILSAFE_THROTTLE);

}

// failsafe_off_event - respond to radio contact being regained
// we must be in AUTO, LAND or RTL modes
// or Stabilize or ACRO mode but with motors disarmed
static void failsafe_off_event()
{
    // no need to do anything except log the error as resolved
    // user can now override roll, pitch, yaw and throttle and even use flight mode switch to restore previous flight mode
    Log_Write_Error(ERROR_SUBSYSTEM_FAILSAFE, ERROR_CODE_ERROR_RESOLVED);
}

static void low_battery_event(void)
{
    // failsafe check
    if (g.failsafe_battery_enabled && !ap.low_battery && motors.armed()) {
        switch(control_mode) {
            case STABILIZE:
            case ACRO:
                // if throttle is zero disarm motors
                if (g.rc_3.control_in == 0) {
                    init_disarm_motors();
                }else{
                    set_mode(LAND);
                }
                break;
            case AUTO:
                if(ap.home_is_set == true && home_distance > g.waypoint_radius) {
                    set_mode(RTL);
                }else{
                    // We have no GPS or are very close to home so we will land
                    set_mode(LAND);
                }
                break;
            default:
                set_mode(LAND);
                break;
        }
    }

    // set the low battery flag
    set_low_battery(true);

    // warn the ground station and log to dataflash
    gcs_send_text_P(SEVERITY_LOW,PSTR("Low Battery!"));
    Log_Write_Error(ERROR_SUBSYSTEM_FAILSAFE, ERROR_CODE_FAILSAFE_BATTERY);

#if COPTER_LEDS == ENABLED
    if ( bitRead(g.copter_leds_mode, 3) ) {         // Only Activate if a battery is connected to avoid alarm on USB only
        piezo_on();
    }
#endif // COPTER_LEDS
}


static void update_events()     // Used for MAV_CMD_DO_REPEAT_SERVO and MAV_CMD_DO_REPEAT_RELAY
{
    if(event_repeat == 0 || (millis() - event_timer) < event_delay)
        return;

    if(event_repeat != 0) {             // event_repeat = -1 means repeat forever
        event_timer = millis();

        if (event_id >= CH_5 && event_id <= CH_8) {
            if(event_repeat%2) {
                hal.rcout->write(event_id, event_value);                 // send to Servos
            } else {
                hal.rcout->write(event_id, event_undo_value);
            }
        }

        if  (event_id == RELAY_TOGGLE) {
            relay.toggle();
        }
        if (event_repeat > 0) {
            event_repeat--;
        }
    }
}