ardupilot/libraries/AP_HAL_ChibiOS/hwdef/DrotekP3Pro/hwdef.dat

# hw definition file for processing by chibios_hwdef.py
# for FMUv4pro hardware (Pixhawk 3 Pro)

define BOARD_TYPE_DEFAULT 14

# MCU class and specific type
MCU STM32F4xx STM32F469xx

# board ID for firmware load
APJ_BOARD_ID 13

# crystal frequency
OSCILLATOR_HZ 24000000


# ChibiOS system timer
STM32_ST_USE_TIMER 5

# flash size
FLASH_SIZE_KB 2048

env OPTIMIZE -O2

# serial port for stdout, disabled so console is on USB
#STDOUT_SERIAL SD7
#STDOUT_BAUDRATE 57600

# order of I2C buses
I2C_ORDER I2C1 I2C2

# now the UART order. These map to the hal.uartA to hal.uartF
# objects. If you use a shorter list then HAL_Empty::UARTDriver
# objects are substituted for later UARTs, or you can leave a gap by
# listing one or more of the uarts as EMPTY
# 1) SERIAL0: console (primary mavlink, usually USB)
# 2) SERIAL3: primary GPS
# 3) SERIAL1: telem1
# 4) SERIAL2: telem2
# 5) SERIAL4: GPS2
# 6) SERIAL5: extra UART (usually RTOS debug console)

# order of UARTs (and USB)
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 USART1 UART7

# UART for IOMCU
IOMCU_UART USART6

# we have a safety switch on IO
define HAL_HAVE_SAFETY_SWITCH 1

# UART4 serial GPS
PA0 UART4_TX UART4
PA1 UART4_RX UART4

# battery connectors
PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)

# VDD sense pin. This is used to sense primary board voltags
PA4 VDD_5V_SENS ADC1 SCALE(2)

# SPI1 is sensors bus
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1

# SPI1 CS pins
PC2 MPU9250_CS CS
PC15 20608_CS CS
PD7 BARO_CS CS
PE15 MAG_CS CS
PH5 EEPROM_CS CS

PA9 VBUS INPUT OPENDRAIN

# now we define the pins that USB is connected on
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1

# these are the pins for SWD debugging with a STlinkv2 or black-magic probe
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD

# PWM output for buzzer
PA15 TIM2_CH1 TIM2 GPIO(77) ALARM

# this defines a couple of general purpose outputs, mapped to GPIO
# numbers 1 and 2 for users
# PB0 EXTERN_GPIO1 OUTPUT GPIO(1)
# PB1 EXTERN_GPIO2 OUTPUT GPIO(2)

#PB0 INPUT PULLUP # RC Input PPM

PB1 LED_GREEN OUTPUT GPIO(0)
PB2 BOOT1 INPUT
PB3 LED_BLUE OUTPUT GPIO(1)

PB6 USART1_TX USART1
PB7 USART1_RX USART1
PA8 USART1_RTS USART1
# PE10 is not a hw CTS pin for USART1
PE10 8266_CTS INPUT

# make GPIOs for ESP8266 available via mavlink relay control as pins
# 60 to 63
PB4 8266_GPIO2 OUTPUT GPIO(60)
PE2 8266_GPI0 INPUT PULLUP GPIO(61)
PE5 8266_PD OUTPUT HIGH GPIO(62)
PE6 8266_RST OUTPUT HIGH GPIO(63)

PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1

PF1 I2C2_SCL I2C2
PF0 I2C2_SDA I2C2

# SPI2 is FRAM
PB10 SPI2_SCK SPI2
PB11 LED_RED OUTPUT GPIO(2)
PB12 CAN2_RX CAN2
PB13 CAN2_TX CAN2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2

PC0 VBUS_nVALID INPUT PULLUP
PC1 BATT2_VOLTAGE_SENS ADC1 SCALE(1)
PC3 BATT2_CURRENT_SENS ADC1 SCALE(1)
#PC4 SAFETY_IN INPUT PULLDOWN

# this sets up the UART for talking to the IOMCU. Note that it is
# vital that this UART has DMA available. See the DMA settings below
# for more information

#  USART6 to IO
PC6 USART6_TX USART6
PC7 USART6_RX USART6

# now setup the pins for the microSD card, if available
PC8 SDIO_D0 SDIO
PC9 SDIO_D1 SDIO
PC10 SDIO_D2 SDIO
PC11 SDIO_D3 SDIO
PC12 SDIO_CK SDIO
PC13 SBUS_INV OUTPUT
PC14 20608_DRDY INPUT

PD0 CAN1_RX CAN1
PD1 CAN1_TX CAN1
PD2 SDIO_CMD SDIO

# USART2 serial2 telem1
PD3 USART2_CTS USART2
PD4 USART2_RTS USART2
PD5 USART2_TX USART2
PD6 USART2_RX USART2

# USART3 serial3 telem2
PD8 USART3_TX USART3
PD9 USART3_RX USART3
PD10 FRAM_CS CS
PD11 USART3_CTS USART3
PD12 USART3_RTS USART3

PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)

PD15 MPU9250_DRDY INPUT

# UART8 serial4 FrSky
PE0 UART8_RX UART8
PE1 UART8_TX UART8
# allow this uart to be inverted for transmit under user control
# the polarity is the value to use on the GPIO to change the polarity
# to the opposite of the default
PA10 UART8_TXINV OUTPUT HIGH GPIO(78) POL(0)

PE3 VDD_SENSORS_EN OUTPUT HIGH

# start peripheral power off, then enable after init
# this prevents a problem with radios that use RTS for
# bootloader hold
PC5  VDD_5V_WIFI_EN OUTPUT HIGH
PF4  nVDD_5V_HIPOWER_EN OUTPUT HIGH
PG10 nVDD_5V_PERIPH_EN OUTPUT HIGH

# UART7 is debug
PE7 UART7_RX UART7 NODMA
PE8 UART7_TX UART7 NODMA

PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
PE12 MAG_DRDY INPUT
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)

# Power flag pins: these tell the MCU the status of the various power
# supplies that are available. The pin names need to exactly match the
# names used in AnalogIn.cpp. 
PB5 VDD_BRICK_nVALID INPUT PULLUP
PG5 VDD_BRICK2_nVALID INPUT PULLUP
PF3 VDD_5V_HIPOWER_nOC INPUT PULLUP
PG4 VDD_5V_PERIPH_nOC INPUT PULLUP

# SPI device table
SPIDEV ms5611      SPI1 DEVID3  BARO_CS    MODE3  20*MHZ 20*MHZ
SPIDEV mpu9250     SPI1 DEVID4  MPU9250_CS MODE3   2*MHZ   4*MHZ
SPIDEV icm20608    SPI1 DEVID6  20608_CS   MODE3   2*MHZ   8*MHZ
SPIDEV lis3mdl     SPI1 DEVID5  MAG_CS     MODE3 500*KHZ 500*KHZ
SPIDEV ramtron     SPI2 DEVID10 FRAM_CS    MODE3   8*MHZ   8*MHZ

# two IMUs
define HAL_DEFAULT_INS_FAST_SAMPLE 1
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU Invensense SPI:mpu9250  ROTATION_ROLL_180_YAW_90

# one baro
BARO MS56XX SPI:ms5611

# two compasses
COMPASS AK8963:probe_mpu9250 0 ROTATION_ROLL_180_YAW_90
COMPASS LIS3MDL SPI:lis3mdl false ROTATION_NONE
define HAL_PROBE_EXTERNAL_I2C_COMPASSES

define HAL_CHIBIOS_ARCH_FMUV4PRO 1

define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"

define HAL_STORAGE_SIZE 16384
define HAL_WITH_RAMTRON 1

# enable FAT filesystem support (needs a microSD defined via SDIO)
define HAL_OS_FATFS_IO 1

# battery setup
define HAL_BATT_VOLT_PIN 2
define HAL_BATT_CURR_PIN 3
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0

# setup serial port defaults for ESP8266
define HAL_SERIAL5_PROTOCOL SerialProtocol_MAVLink2
define HAL_SERIAL5_BAUD 921600

# We can't share the IO UART (USART6).
DMA_NOSHARE USART6_TX USART6_RX ADC1
DMA_PRIORITY USART6*

ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_lowpolh.bin