2020-04-17 18:28:13 -03:00
|
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
|
# mRo Nexus CAN flight controller bootloader
|
|
|
|
|
# M10084
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
|
|
|
|
|
|
# USB setup
|
|
|
|
|
USB_STRING_MANUFACTURER "mRo"
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 25000000
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 1015
|
|
|
|
|
|
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
|
|
|
|
|
|
# bootloader is installed at zero offset
|
|
|
|
|
FLASH_RESERVE_START_KB 0
|
|
|
|
|
|
|
|
|
|
# the location where the bootloader will put the firmware
|
|
|
|
|
# the H743 has 128k sectors
|
|
|
|
|
FLASH_BOOTLOADER_LOAD_KB 128
|
|
|
|
|
|
|
|
|
|
PB0 LED_BOOTLOADER OUTPUT
|
|
|
|
|
|
|
|
|
|
# define all 3 to make LED output White.
|
|
|
|
|
PA6 LED_ACTIVITY OUTPUT
|
|
|
|
|
PA7 LED_ACTIVITY2 OUTPUT
|
|
|
|
|
# PB11 LED_ACTIVITY3 OUTPUT
|
|
|
|
|
|
|
|
|
|
define HAL_LED_ON 0
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# order of UARTs (and USB)
|
2020-04-24 08:10:08 -03:00
|
|
|
SERIAL_ORDER OTG1 UART7
|
2020-04-17 18:28:13 -03:00
|
|
|
|
|
|
|
|
PE7 UART7_RX UART7
|
|
|
|
|
PE8 UART7_TX UART7
|
|
|
|
|
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
define HAL_USE_EMPTY_STORAGE 1
|
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
|
|
|
|
|
|
# Add CS pins to ensure they are high in bootloader
|
|
|
|
|
PB12 CS_ADIS16470 CS
|
|
|
|
|
PA15 CS_ICM40609D CS
|
|
|
|
|
PE3 CS_DPS310 CS
|
|
|
|
|
PB11 CS_RM3100 CS
|
|
|
|
|
PE4 CS_FRAM CS
|
|
|
|
|
|
|
|
|
|
# This is the reset line for the adis16470. This will force a reset upon reboot.
|
|
|
|
|
PB1 nRST_ADIS OUTPUT LOW
|
