2021-10-17 20:25:55 -03:00
|
|
|
# hw definition file for processing by chibios_pins.py
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32G4xx STM32G491xx
|
|
|
|
|
|
|
|
|
|
# use DNA
|
|
|
|
|
define HAL_CAN_DEFAULT_NODE_ID 0
|
|
|
|
|
|
|
|
|
|
define CAN_APP_NODE_NAME "io.mrobotics.mRo-M10095"
|
|
|
|
|
|
|
|
|
|
# bootloader starts firmware at 26k + 4k (STORAGE_FLASH)
|
|
|
|
|
FLASH_RESERVE_START_KB 30
|
|
|
|
|
|
|
|
|
|
# store parameters in pages 13 and 14
|
2021-10-27 02:32:43 -03:00
|
|
|
STORAGE_FLASH_PAGE 13
|
2021-10-17 20:25:55 -03:00
|
|
|
define HAL_STORAGE_SIZE 800
|
|
|
|
|
|
|
|
|
|
# setup build for a peripheral firmware
|
|
|
|
|
env AP_PERIPH 1
|
|
|
|
|
|
|
|
|
|
# enable watchdog
|
|
|
|
|
define HAL_WATCHDOG_ENABLED_DEFAULT true
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
|
|
# assume the 512k flash part
|
|
|
|
|
FLASH_SIZE_KB 512
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 1041
|
|
|
|
|
|
|
|
|
|
define HAL_CAN_POOL_SIZE 6000
|
|
|
|
|
|
|
|
|
|
# LEDs
|
|
|
|
|
PA4 LED OUTPUT HIGH
|
|
|
|
|
|
|
|
|
|
# debugger support
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# Order of I2C buses
|
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
|
|
|
|
|
|
# this board only has a single I2C bus so make it external
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
|
|
|
|
|
|
# Now the first I2C bus. The pin speeds are automatically setup
|
|
|
|
|
# correctly, but can be overridden here if needed.
|
|
|
|
|
PA15 I2C1_SCL I2C1
|
|
|
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
|
|
|
|
|
|
# an I2C baro (DPS310)
|
|
|
|
|
BARO DPS280 I2C:0:0x77
|
|
|
|
|
|
|
|
|
|
define HAL_PERIPH_ENABLE_BARO
|
|
|
|
|
|
|
|
|
|
PA0 VSENSE50 ADC1 SCALE(3)
|
|
|
|
|
PA1 VSENSE3v3 ADC1 SCALE(2)
|
|
|
|
|
|
|
|
|
|
define DMA_RESERVE_SIZE 2048
|
|
|
|
|
|
|
|
|
|
define HAL_USE_ADC TRUE
|
|
|
|
|
|
|
|
|
|
define STM32_ADC_USE_ADC1 TRUE
|
|
|
|
|
|
|
|
|
|
# order of UARTs
|
|
|
|
|
SERIAL_ORDER USART1
|
|
|
|
|
|
|
|
|
|
STDOUT_SERIAL SD1
|
|
|
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
|
|
|
|
|
|
# USART1, telemetry
|
|
|
|
|
PA9 USART1_TX USART1 SPEED_HIGH
|
|
|
|
|
PA10 USART1_RX USART1 SPEED_HIGH
|
|
|
|
|
|
|
|
|
|
# stack for fast interrupts
|
|
|
|
|
define PORT_INT_REQUIRED_STACK 64
|
|
|
|
|
|
|
|
|
|
define HAL_DISABLE_LOOP_DELAY
|
|
|
|
|
|
|
|
|
|
PA11 CAN1_RX CAN1
|
|
|
|
|
PA12 CAN1_TX CAN1
|
|
|
|
|
|
|
|
|
|
define HAL_NO_MONITOR_THREAD
|
|
|
|
|
|
|
|
|
|
define HAL_MINIMIZE_FEATURES 0
|
|
|
|
|
|
|
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 512
|
|
|
|
|
|
|
|
|
|
# keep ROMFS uncompressed as we don't have enough RAM
|
|
|
|
|
# to uncompress the bootloader at runtime
|
|
|
|
|
env ROMFS_UNCOMPRESSED True
|
|
|
|
|
|
|
|
|
|
# don't share any DMA channels (there are enough for everyone)
|
|
|
|
|
DMA_NOSHARE *
|
