2018-03-04 03:14:46 -04:00
|
|
|
# hw definition file for processing by chibios_pins.py
|
|
|
|
|
# for OMNIBUSF7V2 hardware.
|
|
|
|
|
@ thanks to betaflight for pin information
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32F7xx STM32F745xx
|
|
|
|
|
|
|
|
|
|
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_OMNIBUSF7V2
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
2018-06-16 08:09:31 -03:00
|
|
|
APJ_BOARD_ID 121
|
2018-03-04 03:14:46 -04:00
|
|
|
|
2018-03-04 06:05:33 -04:00
|
|
|
# crystal frequency, setup to use external oscillator
|
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
|
|
define STM32_LSECLK 32768U
|
|
|
|
|
define STM32_LSEDRV (3U << 3U)
|
|
|
|
|
|
|
|
|
|
define STM32_PLLSRC STM32_PLLSRC_HSE
|
|
|
|
|
define STM32_PLLM_VALUE 8
|
|
|
|
|
define STM32_PLLN_VALUE 432
|
|
|
|
|
define STM32_PLLP_VALUE 2
|
|
|
|
|
define STM32_PLLQ_VALUE 9
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
FLASH_SIZE_KB 1024
|
2018-03-04 06:05:33 -04:00
|
|
|
|
2018-06-16 08:09:31 -03:00
|
|
|
# reserve one sector for bootloader and 2 for storage
|
|
|
|
|
FLASH_RESERVE_START_KB 96
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
# board voltage
|
|
|
|
|
STM32_VDD 330U
|
|
|
|
|
|
|
|
|
|
# only one I2C bus
|
2018-07-29 12:09:31 -03:00
|
|
|
I2C_ORDER I2C2
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
# order of UARTs (and USB)
|
2018-07-29 12:09:31 -03:00
|
|
|
UART_ORDER OTG1 USART6 USART1 USART3
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
PE0 LED0 OUTPUT LOW
|
2018-06-27 00:01:30 -03:00
|
|
|
PD15 BUZZER OUTPUT
|
2018-03-04 03:14:46 -04:00
|
|
|
|
2018-03-04 06:05:33 -04:00
|
|
|
# ICM-20608 on SPI1
|
2018-03-04 03:14:46 -04:00
|
|
|
PA4 MPU6000_CS CS
|
|
|
|
|
|
2018-03-04 06:05:33 -04:00
|
|
|
# MPU6500 on SPI3
|
|
|
|
|
PA15 MPU6500_CS CS
|
|
|
|
|
|
|
|
|
|
# SPI1 for IMU and baro
|
2018-03-04 03:14:46 -04:00
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
|
|
|
|
|
|
# SPI2 for MAX7456 OSD
|
|
|
|
|
PB12 MAX7456_CS CS
|
|
|
|
|
PB13 SPI2_SCK SPI2
|
|
|
|
|
PB14 SPI2_MISO SPI2
|
|
|
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
|
|
|
|
|
|
PC10 SPI3_SCK SPI3
|
|
|
|
|
PC11 SPI3_MISO SPI3
|
|
|
|
|
PC12 SPI3_MOSI SPI3
|
|
|
|
|
|
|
|
|
|
# SPI4 for SDCard
|
2018-06-27 00:01:30 -03:00
|
|
|
PE4 SDCARD_CS CS
|
2018-03-04 03:14:46 -04:00
|
|
|
PE2 SPI4_SCK SPI4
|
|
|
|
|
PE5 SPI4_MISO SPI4
|
|
|
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
|
|
|
|
|
|
# optional I2C device2, shared with USART3
|
2018-07-29 12:09:31 -03:00
|
|
|
PB10 I2C2_SCL I2C2
|
|
|
|
|
PB11 I2C2_SDA I2C2
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
# baro is BMP280 on SPI1
|
|
|
|
|
PA1 BMP280_CS CS
|
|
|
|
|
|
|
|
|
|
# mag is on I2C if connected
|
|
|
|
|
|
|
|
|
|
PC3 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PC2 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
|
|
|
|
|
PC5 RSSI_ADC ADC1
|
|
|
|
|
|
|
|
|
|
# USART1
|
2018-06-27 00:01:30 -03:00
|
|
|
PA10 USART1_RX USART1
|
|
|
|
|
PA9 USART1_TX USART1
|
2018-03-04 03:14:46 -04:00
|
|
|
|
2018-07-29 20:51:42 -03:00
|
|
|
# USART2 for RC input, RX only
|
2019-03-14 19:36:51 -03:00
|
|
|
PA3 TIM9_CH2 TIM9 RCININT FLOAT LOW
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
# USART3
|
2018-07-29 12:09:31 -03:00
|
|
|
PD9 USART3_RX USART3
|
|
|
|
|
PD8 USART3_TX USART3
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
# USART6
|
2018-06-27 00:01:30 -03:00
|
|
|
PC7 USART6_RX USART6
|
|
|
|
|
PC6 USART6_TX USART6
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
# UART7, RX only?
|
|
|
|
|
#PE7 UART7_RX UART7
|
|
|
|
|
|
2018-10-31 02:10:16 -03:00
|
|
|
PB0 TIM3_CH3 TIM3 PWM(1) GPIO(50)
|
|
|
|
|
PB1 TIM3_CH4 TIM3 PWM(2) GPIO(51)
|
|
|
|
|
PE9 TIM1_CH1 TIM1 PWM(3) GPIO(52)
|
|
|
|
|
PE11 TIM1_CH2 TIM1 PWM(4) GPIO(53)
|
2018-03-04 03:14:46 -04:00
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
|
define STORAGE_FLASH_PAGE 1
|
2018-03-04 06:05:33 -04:00
|
|
|
|
|
|
|
|
# spi devices
|
2018-06-27 00:01:30 -03:00
|
|
|
SPIDEV bmp280 SPI1 DEVID1 BMP280_CS MODE3 1*MHZ 8*MHZ
|
2018-03-04 06:05:33 -04:00
|
|
|
SPIDEV mpu6000 SPI1 DEVID2 MPU6000_CS MODE3 1*MHZ 4*MHZ
|
|
|
|
|
SPIDEV mpu6500 SPI3 DEVID1 MPU6500_CS MODE3 1*MHZ 4*MHZ
|
2018-06-27 00:01:30 -03:00
|
|
|
SPIDEV sdcard SPI4 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
|
|
|
SPIDEV osd SPI2 DEVID1 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
2018-03-04 06:05:33 -04:00
|
|
|
|
2018-06-27 00:01:30 -03:00
|
|
|
define HAL_OS_FATFS_IO 1
|
2018-07-29 20:51:42 -03:00
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
|
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
2018-07-13 07:14:03 -03:00
|
|
|
|
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
|
|
|
# external compass types
|
2018-06-27 00:01:30 -03:00
|
|
|
define ALLOW_ARM_NO_COMPASS
|
2018-07-13 07:14:03 -03:00
|
|
|
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
|
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
2018-07-28 02:36:37 -03:00
|
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
2018-07-13 07:14:03 -03:00
|
|
|
|
2018-03-04 06:05:33 -04:00
|
|
|
define HAL_BARO_DEFAULT HAL_BARO_BMP280_SPI
|
2018-06-27 00:01:30 -03:00
|
|
|
|
|
|
|
|
define OSD_ENABLED ENABLED
|
2018-10-31 21:10:21 -03:00
|
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
2018-07-09 04:58:57 -03:00
|
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
2019-06-05 21:21:58 -03:00
|
|
|
|
|
|
|
|
# we are low on flash on this board
|
|
|
|
|
define HAL_MINIMIZE_FEATURES 1
|
