MAV_CMD_NAV_WAYPOINT=16,/* Navigate to waypoint. |Hold time in decimal seconds. (ignored by fixed wing, time to stay at waypoint for rotary wing)| Acceptance radius in meters (if the sphere with this radius is hit, the waypoint counts as reached)| 0 to pass through the WP, if > 0 radius in meters to pass by WP. Positive value for clockwise orbit, negative value for counter-clockwise orbit. Allows trajectory control.| Desired yaw angle at waypoint (rotary wing)| Latitude| Longitude| Altitude| */
MAV_CMD_NAV_LOITER_UNLIM=17,/* Loiter around this waypoint an unlimited amount of time |Empty| Empty| Radius around waypoint, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude| */
MAV_CMD_NAV_LOITER_TURNS=18,/* Loiter around this waypoint for X turns |Turns| Empty| Radius around waypoint, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude| */
MAV_CMD_NAV_LOITER_TIME=19,/* Loiter around this waypoint for X seconds |Seconds (decimal)| Empty| Radius around waypoint, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude| */
MAV_CMD_NAV_PATHPLANNING=81,/* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal, in compass degrees, [0..360]| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal| */
MAV_CMD_NAV_LAST=95,/* NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_CONDITION_DELAY=112,/* Delay mission state machine. |Delay in seconds (decimal)| Empty| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_CONDITION_CHANGE_ALT=113,/* Ascend/descend at rate. Delay mission state machine until desired altitude reached. |Descent / Ascend rate (m/s)| Empty| Empty| Empty| Empty| Empty| Finish Altitude| */
MAV_CMD_CONDITION_DISTANCE=114,/* Delay mission state machine until within desired distance of next NAV point. |Distance (meters)| Empty| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_CONDITION_YAW=115,/* Reach a certain target angle. |target angle: [0-360], 0 is north| speed during yaw change:[deg per second]| direction: negative: counter clockwise, positive: clockwise [-1,1]| relative offset or absolute angle: [ 1,0]| Empty| Empty| Empty| */
MAV_CMD_CONDITION_LAST=159,/* NOP - This command is only used to mark the upper limit of the CONDITION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_SET_MODE=176,/* Set system mode. |Mode, as defined by ENUM MAV_MODE| Empty| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_JUMP=177,/* Jump to the desired command in the mission list. Repeat this action only the specified number of times |Sequence number| Repeat count| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_CHANGE_SPEED=178,/* Change speed and/or throttle set points. |Speed type (0=Airspeed, 1=Ground Speed)| Speed (m/s, -1 indicates no change)| Throttle ( Percent, -1 indicates no change)| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_SET_HOME=179,/* Changes the home location either to the current location or a specified location. |Use current (1=use current location, 0=use specified location)| Empty| Empty| Empty| Latitude| Longitude| Altitude| */
MAV_CMD_DO_SET_PARAMETER=180,/* Set a system parameter. Caution! Use of this command requires knowledge of the numeric enumeration value of the parameter. |Parameter number| Parameter value| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_SET_RELAY=181,/* Set a relay to a condition. |Relay number| Setting (1=on, 0=off, others possible depending on system hardware)| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_REPEAT_RELAY=182,/* Cycle a relay on and off for a desired number of cyles with a desired period. |Relay number| Cycle count| Cycle time (seconds, decimal)| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_SET_SERVO=183,/* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_REPEAT_SERVO=184,/* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty| */
MAV_CMD_DO_CONTROL_VIDEO=200,/* Control onboard camera capturing. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty| */
MAV_CMD_DO_SET_ROI=201,/* Sets the region of interest (ROI) for a sensor set or the
MAV_CMD_DO_LAST=240,/* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_PREFLIGHT_CALIBRATION=241,/* Trigger calibration. This command will be only accepted if in pre-flight mode. |Gyro calibration: 0: no, 1: yes| Magnetometer calibration: 0: no, 1: yes| Ground pressure: 0: no, 1: yes| Radio calibration: 0: no, 1: yes| Empty| Empty| Empty| */
MAV_CMD_PREFLIGHT_STORAGE=245,/* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM| Reserved| Reserved| Empty| Empty| Empty| */
