mirror of https://github.com/ArduPilot/ardupilot
69 lines
1.3 KiB
PHP
69 lines
1.3 KiB
PHP
|
# MCU class and specific type
|
||
|
|
MCU STM32L431 STM32L431xx
|
||
|
|
|
||
|
|
# bootloader starts firmware at 36k + 4k (STORAGE_FLASH)
|
||
|
|
FLASH_RESERVE_START_KB 40
|
||
|
|
FLASH_SIZE_KB 256
|
||
|
|
|
||
|
|
# store parameters in pages 18 and 19
|
||
|
|
STORAGE_FLASH_PAGE 18
|
||
|
|
define HAL_STORAGE_SIZE 800
|
||
|
|
|
||
|
|
# ChibiOS system timer
|
||
|
|
STM32_ST_USE_TIMER 15
|
||
|
|
define CH_CFG_ST_RESOLUTION 16
|
||
|
|
|
||
|
|
# board ID for firmware load
|
||
|
|
APJ_BOARD_ID 1080
|
||
|
|
|
||
|
|
# crystal frequency
|
||
|
|
OSCILLATOR_HZ 8000000
|
||
|
|
|
||
|
|
env AP_PERIPH 1
|
||
|
|
|
||
|
|
STDOUT_SERIAL SD1
|
||
|
|
STDOUT_BAUDRATE 57600
|
||
|
|
|
||
|
|
define HAL_NO_GPIO_IRQ
|
||
|
|
define SERIAL_BUFFERS_SIZE 512
|
||
|
|
define PORT_INT_REQUIRED_STACK 64
|
||
|
|
|
||
|
|
define DMA_RESERVE_SIZE 0
|
||
|
|
|
||
|
|
# MAIN_STACK is stack for ISR handlers
|
||
|
|
MAIN_STACK 0x300
|
||
|
|
|
||
|
|
# PROCESS_STACK controls stack for main thread
|
||
|
|
PROCESS_STACK 0xA00
|
||
|
|
|
||
|
|
define HAL_DISABLE_LOOP_DELAY
|
||
|
|
|
||
|
|
define HAL_GCS_ENABLED 0
|
||
|
|
define HAL_NO_MONITOR_THREAD
|
||
|
|
define HAL_NO_LOGGING
|
||
|
|
|
||
|
|
# setup a small defaults.parm
|
||
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 512
|
||
|
|
|
||
|
|
#ACT LED
|
||
|
|
PB3 LED OUTPUT HIGH
|
||
|
|
define HAL_LED_ON 1
|
||
|
|
|
||
|
|
# debugger support
|
||
|
|
PA13 JTMS-SWDIO SWD
|
||
|
|
PA14 JTCK-SWCLK SWD
|
||
|
|
|
||
|
|
#CAN bus
|
||
|
|
CAN_ORDER 1
|
||
|
|
PB8 CAN1_RX CAN1
|
||
|
|
PB9 CAN1_TX CAN1
|
||
|
|
|
||
|
|
define HAL_CAN_POOL_SIZE 6000
|
||
|
|
|
||
|
|
# allow for reboot command for faster development
|
||
|
|
define HAL_PERIPH_LISTEN_FOR_SERIAL_UART_REBOOT_CMD_PORT 0
|
||
|
|
|
||
|
|
# keep ROMFS uncompressed as we don't have enough RAM
|
||
|
|
# to uncompress the bootloader at runtime
|
||
|
|
env ROMFS_UNCOMPRESSED True
|