daemon threads run while the interpreter is shutting down; instead,
these threads are now killed when they try to take the GIL), as it seems
to break some existing code.
Heavily revised, comprising revisions:
46640 - original trunk revision (backed out in r46655)
46647 - markup fix (backed out in r46655)
46692:46918 merged from branch aimacintyre-sf1454481
branch tested on buildbots (Windows buildbots had problems
not related to these changes).
46640 Patch #1454481: Make thread stack size runtime tunable.
46647 Markup fix
The first is causing many buildbots to fail test runs, and there
are multiple causes with seemingly no immediate prospects for
repairing them. See python-dev discussion.
Note that a branch can (and should) be created for resolving these
problems, like
svn copy svn+ssh://svn.python.org/python/trunk -r46640 svn+ssh://svn.python.org/python/branches/NEW_BRANCH
followed by merging rev 46647 to the new branch.
[ 960406 ] unblock signals in threads
although the changes do not correspond exactly to any patch attached to
that report.
Non-main threads no longer have all signals masked.
A different interface to readline is used.
The handling of signals inside calls to PyOS_Readline is now rather
different.
These changes are all a bit scary! Review and cross-platform testing
much appreciated.
Cygwin's pthread_sigmask() implementation appears to be buggy. This
patch works around this problem by using sigprocmask() instead.
This patch is implemented in a general way so it could be used by other
platforms too. If this approach is deemed too risky, then I can work up
a patch that just hacks Python/thread_pthread.h for Cygwin.
Note that I tested this patch against 2.3c1 under Red Hat Linux 8.0 too.
[snip]
And finally, I need someone to regenerate pyconfig.h.in and configure
with the same versions of the autotools that are normally used by
Python.
Neal kindly regenerated pyconfig.h.in and configure for me.
This changes Pythread_start_thread() to return the thread ID, or -1
for an error. (It's technically an incompatible API change, but I
doubt anyone calls it.)
This patch updates Python/thread_pthread.h to mask all
signals for any thread created. This will keep all
signals masked for any thread that isn't the initial
thread. For Solaris and Linux, the two platforms I was
able to test it on, it solves bug #465673 (pthreads
need signal protection) and probably will solve bug
#219772 (Interactive InterPreter+ Thread -> core dump
at exit).
I'd be great if this could get some testing on other
platforms, especially HP-UX pre 11.00 and post 11.00,
as I had to make some guesses for the DCE thread case.
AIX is also a concern as I saw some mention of using
sigthreadmask() as a pthread_sigmask() equivalent, but
this patch doesn't use sigthreadmask(). I don't have
access to AIX.
by bbrox@bbrox.org / lionel.ulmer@free.fr.
This adds a configure check and if all goes well turns on the
PTHREAD_SCOPE_SYSTEM thread attribute for new threads.
This should remove the need to add tiny sleeps at the start of threads
to allow other threads to be scheduled.
- Fix bug in thread_pthread.h::PyThread_get_thread_ident() where
sizeof(pthread) < sizeof(long).
- Add 'configure' for:
- SIZEOF_PTHREAD is pthread_t can be included via <pthread.h>
- setting Monterey system name
- appropriate CC,LINKCC,LDSHARED,OPT, and CCSHARED for Monterey
- Add section in README for Monterey build
The common technique for printing out a pointer has been to cast to a long
and use the "%lx" printf modifier. This is incorrect on Win64 where casting
to a long truncates the pointer. The "%p" formatter should be used instead.
The problem as stated by Tim:
> Unfortunately, the C committee refused to define what %p conversion "looks
> like" -- they explicitly allowed it to be implementation-defined. Older
> versions of Microsoft C even stuck a colon in the middle of the address (in
> the days of segment+offset addressing)!
The result is that the hex value of a pointer will maybe/maybe not have a 0x
prepended to it.
Notes on the patch:
There are two main classes of changes:
- in the various repr() functions that print out pointers
- debugging printf's in the various thread_*.h files (these are why the
patch is large)
Closes SourceForge patch #100505.
"""
Spec says that on success pthread_create returns 0. It does not say
that an error code will be < 0. Linux glibc2 pthread_create() returns
ENOMEM (12) when one exceed process limits. (It looks like it should
return EAGAIN, but that's another story.)
For reference, see:
http://www.opengroup.org/onlinepubs/7908799/xsh/pthread_create.html
"""
[I have a feeling that similar bugs were fixed before; perhaps someone
could check that all error checks no check for != 0?]
Also (non-BSDI specific):
- Change the CHECK_STATUS() macro so it tests for nonzero error codes
instead of negative error codes only (this was needed for BSDI, but
appears to be correct according to the PTHREADS spec).
- use memset() to zero out the allocated lock structure. Again, this
was needed for BSDI, but can't hurt elsewhere either.
Antoine Pitrou
Benjamin Peterson
Jesus Cea
Ned Deily
Amaury Forgeot d'Arc
Andrew MacIntyre
Tim Peters
Hye-Shik Chang
Armin Rigo
Martin v. Löwis
Anthony Baxter
Michael W. Hudson
Skip Montanaro
Jack Jansen
Jason Tishler
Fred Drake
Guido van Rossum
Trent Mick
Thomas Wouters