forked from rrcarlosr/Jetpack
522 lines
12 KiB
C
522 lines
12 KiB
C
/*
|
|
* This is a driver for the SDHC controller found in Freescale MX2/MX3
|
|
* SoCs. It is basically the same hardware as found on MX1 (imxmmc.c).
|
|
* Unlike the hardware found on MX1, this hardware just works and does
|
|
* not need all the quirks found in imxmmc.c, hence the seperate driver.
|
|
*
|
|
* Copyright (C) 2009 Ilya Yanok, <yanok@emcraft.com>
|
|
* Copyright (C) 2008 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de>
|
|
* Copyright (C) 2006 Pavel Pisa, PiKRON <ppisa@pikron.com>
|
|
*
|
|
* derived from pxamci.c by Russell King
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
*/
|
|
|
|
#include <config.h>
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <mmc.h>
|
|
#include <part.h>
|
|
#include <malloc.h>
|
|
#include <mmc.h>
|
|
#include <asm/errno.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/clock.h>
|
|
|
|
#define DRIVER_NAME "mxc-mmc"
|
|
|
|
struct mxcmci_regs {
|
|
u32 str_stp_clk;
|
|
u32 status;
|
|
u32 clk_rate;
|
|
u32 cmd_dat_cont;
|
|
u32 res_to;
|
|
u32 read_to;
|
|
u32 blk_len;
|
|
u32 nob;
|
|
u32 rev_no;
|
|
u32 int_cntr;
|
|
u32 cmd;
|
|
u32 arg;
|
|
u32 pad;
|
|
u32 res_fifo;
|
|
u32 buffer_access;
|
|
};
|
|
|
|
#define STR_STP_CLK_RESET (1 << 3)
|
|
#define STR_STP_CLK_START_CLK (1 << 1)
|
|
#define STR_STP_CLK_STOP_CLK (1 << 0)
|
|
|
|
#define STATUS_CARD_INSERTION (1 << 31)
|
|
#define STATUS_CARD_REMOVAL (1 << 30)
|
|
#define STATUS_YBUF_EMPTY (1 << 29)
|
|
#define STATUS_XBUF_EMPTY (1 << 28)
|
|
#define STATUS_YBUF_FULL (1 << 27)
|
|
#define STATUS_XBUF_FULL (1 << 26)
|
|
#define STATUS_BUF_UND_RUN (1 << 25)
|
|
#define STATUS_BUF_OVFL (1 << 24)
|
|
#define STATUS_SDIO_INT_ACTIVE (1 << 14)
|
|
#define STATUS_END_CMD_RESP (1 << 13)
|
|
#define STATUS_WRITE_OP_DONE (1 << 12)
|
|
#define STATUS_DATA_TRANS_DONE (1 << 11)
|
|
#define STATUS_READ_OP_DONE (1 << 11)
|
|
#define STATUS_WR_CRC_ERROR_CODE_MASK (3 << 10)
|
|
#define STATUS_CARD_BUS_CLK_RUN (1 << 8)
|
|
#define STATUS_BUF_READ_RDY (1 << 7)
|
|
#define STATUS_BUF_WRITE_RDY (1 << 6)
|
|
#define STATUS_RESP_CRC_ERR (1 << 5)
|
|
#define STATUS_CRC_READ_ERR (1 << 3)
|
|
#define STATUS_CRC_WRITE_ERR (1 << 2)
|
|
#define STATUS_TIME_OUT_RESP (1 << 1)
|
|
#define STATUS_TIME_OUT_READ (1 << 0)
|
|
#define STATUS_ERR_MASK 0x2f
|
|
|
|
#define CMD_DAT_CONT_CMD_RESP_LONG_OFF (1 << 12)
|
|
#define CMD_DAT_CONT_STOP_READWAIT (1 << 11)
|
|
#define CMD_DAT_CONT_START_READWAIT (1 << 10)
|
|
#define CMD_DAT_CONT_BUS_WIDTH_4 (2 << 8)
|
|
#define CMD_DAT_CONT_INIT (1 << 7)
|
|
#define CMD_DAT_CONT_WRITE (1 << 4)
|
|
#define CMD_DAT_CONT_DATA_ENABLE (1 << 3)
|
|
#define CMD_DAT_CONT_RESPONSE_48BIT_CRC (1 << 0)
|
|
#define CMD_DAT_CONT_RESPONSE_136BIT (2 << 0)
|
|
#define CMD_DAT_CONT_RESPONSE_48BIT (3 << 0)
|
|
|
|
#define INT_SDIO_INT_WKP_EN (1 << 18)
|
|
#define INT_CARD_INSERTION_WKP_EN (1 << 17)
|
|
#define INT_CARD_REMOVAL_WKP_EN (1 << 16)
|
|
#define INT_CARD_INSERTION_EN (1 << 15)
|
|
#define INT_CARD_REMOVAL_EN (1 << 14)
|
|
#define INT_SDIO_IRQ_EN (1 << 13)
|
|
#define INT_DAT0_EN (1 << 12)
|
|
#define INT_BUF_READ_EN (1 << 4)
|
|
#define INT_BUF_WRITE_EN (1 << 3)
|
|
#define INT_END_CMD_RES_EN (1 << 2)
|
|
#define INT_WRITE_OP_DONE_EN (1 << 1)
|
|
#define INT_READ_OP_EN (1 << 0)
|
|
|
|
struct mxcmci_host {
|
|
struct mmc *mmc;
|
|
struct mxcmci_regs *base;
|
|
int irq;
|
|
int detect_irq;
|
|
int dma;
|
|
int do_dma;
|
|
unsigned int power_mode;
|
|
|
|
struct mmc_cmd *cmd;
|
|
struct mmc_data *data;
|
|
|
|
unsigned int dma_nents;
|
|
unsigned int datasize;
|
|
unsigned int dma_dir;
|
|
|
|
u16 rev_no;
|
|
unsigned int cmdat;
|
|
|
|
int clock;
|
|
};
|
|
|
|
static struct mxcmci_host mxcmci_host;
|
|
|
|
/* maintainer note: do we really want to have a global host pointer? */
|
|
static struct mxcmci_host *host = &mxcmci_host;
|
|
|
|
static inline int mxcmci_use_dma(struct mxcmci_host *host)
|
|
{
|
|
return host->do_dma;
|
|
}
|
|
|
|
static void mxcmci_softreset(struct mxcmci_host *host)
|
|
{
|
|
int i;
|
|
|
|
/* reset sequence */
|
|
writel(STR_STP_CLK_RESET, &host->base->str_stp_clk);
|
|
writel(STR_STP_CLK_RESET | STR_STP_CLK_START_CLK,
|
|
&host->base->str_stp_clk);
|
|
|
|
for (i = 0; i < 8; i++)
|
|
writel(STR_STP_CLK_START_CLK, &host->base->str_stp_clk);
|
|
|
|
writel(0xff, &host->base->res_to);
|
|
}
|
|
|
|
static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
|
|
{
|
|
unsigned int nob = data->blocks;
|
|
unsigned int blksz = data->blocksize;
|
|
unsigned int datasize = nob * blksz;
|
|
|
|
host->data = data;
|
|
|
|
writel(nob, &host->base->nob);
|
|
writel(blksz, &host->base->blk_len);
|
|
host->datasize = datasize;
|
|
}
|
|
|
|
static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_cmd *cmd,
|
|
unsigned int cmdat)
|
|
{
|
|
if (host->cmd != NULL)
|
|
printf("mxcmci: error!\n");
|
|
host->cmd = cmd;
|
|
|
|
switch (cmd->resp_type) {
|
|
case MMC_RSP_R1: /* short CRC, OPCODE */
|
|
case MMC_RSP_R1b:/* short CRC, OPCODE, BUSY */
|
|
cmdat |= CMD_DAT_CONT_RESPONSE_48BIT_CRC;
|
|
break;
|
|
case MMC_RSP_R2: /* long 136 bit + CRC */
|
|
cmdat |= CMD_DAT_CONT_RESPONSE_136BIT;
|
|
break;
|
|
case MMC_RSP_R3: /* short */
|
|
cmdat |= CMD_DAT_CONT_RESPONSE_48BIT;
|
|
break;
|
|
case MMC_RSP_NONE:
|
|
break;
|
|
default:
|
|
printf("mxcmci: unhandled response type 0x%x\n",
|
|
cmd->resp_type);
|
|
return -EINVAL;
|
|
}
|
|
|
|
writel(cmd->cmdidx, &host->base->cmd);
|
|
writel(cmd->cmdarg, &host->base->arg);
|
|
writel(cmdat, &host->base->cmd_dat_cont);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void mxcmci_finish_request(struct mxcmci_host *host,
|
|
struct mmc_cmd *cmd, struct mmc_data *data)
|
|
{
|
|
host->cmd = NULL;
|
|
host->data = NULL;
|
|
}
|
|
|
|
static int mxcmci_finish_data(struct mxcmci_host *host, unsigned int stat)
|
|
{
|
|
int data_error = 0;
|
|
|
|
if (stat & STATUS_ERR_MASK) {
|
|
printf("request failed. status: 0x%08x\n",
|
|
stat);
|
|
if (stat & STATUS_CRC_READ_ERR) {
|
|
data_error = -EILSEQ;
|
|
} else if (stat & STATUS_CRC_WRITE_ERR) {
|
|
u32 err_code = (stat >> 9) & 0x3;
|
|
if (err_code == 2) /* No CRC response */
|
|
data_error = TIMEOUT;
|
|
else
|
|
data_error = -EILSEQ;
|
|
} else if (stat & STATUS_TIME_OUT_READ) {
|
|
data_error = TIMEOUT;
|
|
} else {
|
|
data_error = -EIO;
|
|
}
|
|
}
|
|
|
|
host->data = NULL;
|
|
|
|
return data_error;
|
|
}
|
|
|
|
static int mxcmci_read_response(struct mxcmci_host *host, unsigned int stat)
|
|
{
|
|
struct mmc_cmd *cmd = host->cmd;
|
|
int i;
|
|
u32 a, b, c;
|
|
u32 *resp = (u32 *)cmd->response;
|
|
|
|
if (!cmd)
|
|
return 0;
|
|
|
|
if (stat & STATUS_TIME_OUT_RESP) {
|
|
printf("CMD TIMEOUT\n");
|
|
return TIMEOUT;
|
|
} else if (stat & STATUS_RESP_CRC_ERR && cmd->resp_type & MMC_RSP_CRC) {
|
|
printf("cmd crc error\n");
|
|
return -EILSEQ;
|
|
}
|
|
|
|
if (cmd->resp_type & MMC_RSP_PRESENT) {
|
|
if (cmd->resp_type & MMC_RSP_136) {
|
|
for (i = 0; i < 4; i++) {
|
|
a = readl(&host->base->res_fifo) & 0xFFFF;
|
|
b = readl(&host->base->res_fifo) & 0xFFFF;
|
|
resp[i] = a << 16 | b;
|
|
}
|
|
} else {
|
|
a = readl(&host->base->res_fifo) & 0xFFFF;
|
|
b = readl(&host->base->res_fifo) & 0xFFFF;
|
|
c = readl(&host->base->res_fifo) & 0xFFFF;
|
|
resp[0] = a << 24 | b << 8 | c >> 8;
|
|
}
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int mxcmci_poll_status(struct mxcmci_host *host, u32 mask)
|
|
{
|
|
u32 stat;
|
|
unsigned long timeout = get_ticks() + CONFIG_SYS_HZ;
|
|
|
|
do {
|
|
stat = readl(&host->base->status);
|
|
if (stat & STATUS_ERR_MASK)
|
|
return stat;
|
|
if (timeout < get_ticks())
|
|
return STATUS_TIME_OUT_READ;
|
|
if (stat & mask)
|
|
return 0;
|
|
} while (1);
|
|
}
|
|
|
|
static int mxcmci_pull(struct mxcmci_host *host, void *_buf, int bytes)
|
|
{
|
|
unsigned int stat;
|
|
u32 *buf = _buf;
|
|
|
|
while (bytes > 3) {
|
|
stat = mxcmci_poll_status(host,
|
|
STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE);
|
|
if (stat)
|
|
return stat;
|
|
*buf++ = readl(&host->base->buffer_access);
|
|
bytes -= 4;
|
|
}
|
|
|
|
if (bytes) {
|
|
u8 *b = (u8 *)buf;
|
|
u32 tmp;
|
|
|
|
stat = mxcmci_poll_status(host,
|
|
STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE);
|
|
if (stat)
|
|
return stat;
|
|
tmp = readl(&host->base->buffer_access);
|
|
memcpy(b, &tmp, bytes);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mxcmci_push(struct mxcmci_host *host, const void *_buf, int bytes)
|
|
{
|
|
unsigned int stat;
|
|
const u32 *buf = _buf;
|
|
|
|
while (bytes > 3) {
|
|
stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
|
|
if (stat)
|
|
return stat;
|
|
writel(*buf++, &host->base->buffer_access);
|
|
bytes -= 4;
|
|
}
|
|
|
|
if (bytes) {
|
|
const u8 *b = (u8 *)buf;
|
|
u32 tmp;
|
|
|
|
stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
|
|
if (stat)
|
|
return stat;
|
|
|
|
memcpy(&tmp, b, bytes);
|
|
writel(tmp, &host->base->buffer_access);
|
|
}
|
|
|
|
stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
|
|
if (stat)
|
|
return stat;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mxcmci_transfer_data(struct mxcmci_host *host)
|
|
{
|
|
struct mmc_data *data = host->data;
|
|
int stat;
|
|
unsigned long length;
|
|
|
|
length = data->blocks * data->blocksize;
|
|
host->datasize = 0;
|
|
|
|
if (data->flags & MMC_DATA_READ) {
|
|
stat = mxcmci_pull(host, data->dest, length);
|
|
if (stat)
|
|
return stat;
|
|
host->datasize += length;
|
|
} else {
|
|
stat = mxcmci_push(host, (const void *)(data->src), length);
|
|
if (stat)
|
|
return stat;
|
|
host->datasize += length;
|
|
stat = mxcmci_poll_status(host, STATUS_WRITE_OP_DONE);
|
|
if (stat)
|
|
return stat;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int mxcmci_cmd_done(struct mxcmci_host *host, unsigned int stat)
|
|
{
|
|
int datastat;
|
|
int ret;
|
|
|
|
ret = mxcmci_read_response(host, stat);
|
|
|
|
if (ret) {
|
|
mxcmci_finish_request(host, host->cmd, host->data);
|
|
return ret;
|
|
}
|
|
|
|
if (!host->data) {
|
|
mxcmci_finish_request(host, host->cmd, host->data);
|
|
return 0;
|
|
}
|
|
|
|
datastat = mxcmci_transfer_data(host);
|
|
ret = mxcmci_finish_data(host, datastat);
|
|
mxcmci_finish_request(host, host->cmd, host->data);
|
|
return ret;
|
|
}
|
|
|
|
static int mxcmci_request(struct mmc *mmc, struct mmc_cmd *cmd,
|
|
struct mmc_data *data)
|
|
{
|
|
struct mxcmci_host *host = mmc->priv;
|
|
unsigned int cmdat = host->cmdat;
|
|
u32 stat;
|
|
int ret;
|
|
|
|
host->cmdat &= ~CMD_DAT_CONT_INIT;
|
|
if (data) {
|
|
mxcmci_setup_data(host, data);
|
|
|
|
cmdat |= CMD_DAT_CONT_DATA_ENABLE;
|
|
|
|
if (data->flags & MMC_DATA_WRITE)
|
|
cmdat |= CMD_DAT_CONT_WRITE;
|
|
}
|
|
|
|
if ((ret = mxcmci_start_cmd(host, cmd, cmdat))) {
|
|
mxcmci_finish_request(host, cmd, data);
|
|
return ret;
|
|
}
|
|
|
|
do {
|
|
stat = readl(&host->base->status);
|
|
writel(stat, &host->base->status);
|
|
} while (!(stat & STATUS_END_CMD_RESP));
|
|
|
|
return mxcmci_cmd_done(host, stat);
|
|
}
|
|
|
|
static void mxcmci_set_clk_rate(struct mxcmci_host *host, unsigned int clk_ios)
|
|
{
|
|
unsigned int divider;
|
|
int prescaler = 0;
|
|
unsigned long clk_in = mxc_get_clock(MXC_ESDHC_CLK);
|
|
|
|
while (prescaler <= 0x800) {
|
|
for (divider = 1; divider <= 0xF; divider++) {
|
|
int x;
|
|
|
|
x = (clk_in / (divider + 1));
|
|
|
|
if (prescaler)
|
|
x /= (prescaler * 2);
|
|
|
|
if (x <= clk_ios)
|
|
break;
|
|
}
|
|
if (divider < 0x10)
|
|
break;
|
|
|
|
if (prescaler == 0)
|
|
prescaler = 1;
|
|
else
|
|
prescaler <<= 1;
|
|
}
|
|
|
|
writel((prescaler << 4) | divider, &host->base->clk_rate);
|
|
}
|
|
|
|
static void mxcmci_set_ios(struct mmc *mmc)
|
|
{
|
|
struct mxcmci_host *host = mmc->priv;
|
|
if (mmc->bus_width == 4)
|
|
host->cmdat |= CMD_DAT_CONT_BUS_WIDTH_4;
|
|
else
|
|
host->cmdat &= ~CMD_DAT_CONT_BUS_WIDTH_4;
|
|
|
|
if (mmc->clock) {
|
|
mxcmci_set_clk_rate(host, mmc->clock);
|
|
writel(STR_STP_CLK_START_CLK, &host->base->str_stp_clk);
|
|
} else {
|
|
writel(STR_STP_CLK_STOP_CLK, &host->base->str_stp_clk);
|
|
}
|
|
|
|
host->clock = mmc->clock;
|
|
}
|
|
|
|
static int mxcmci_init(struct mmc *mmc)
|
|
{
|
|
struct mxcmci_host *host = mmc->priv;
|
|
|
|
mxcmci_softreset(host);
|
|
|
|
host->rev_no = readl(&host->base->rev_no);
|
|
if (host->rev_no != 0x400) {
|
|
printf("wrong rev.no. 0x%08x. aborting.\n",
|
|
host->rev_no);
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* recommended in data sheet */
|
|
writel(0x2db4, &host->base->read_to);
|
|
|
|
writel(0, &host->base->int_cntr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct mmc_ops mxcmci_ops = {
|
|
.send_cmd = mxcmci_request,
|
|
.set_ios = mxcmci_set_ios,
|
|
.init = mxcmci_init,
|
|
};
|
|
|
|
static struct mmc_config mxcmci_cfg = {
|
|
.name = "MXC MCI",
|
|
.ops = &mxcmci_ops,
|
|
.host_caps = MMC_MODE_4BIT,
|
|
.voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
|
|
.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT,
|
|
};
|
|
|
|
static int mxcmci_initialize(bd_t *bis)
|
|
{
|
|
host->base = (struct mxcmci_regs *)CONFIG_MXC_MCI_REGS_BASE;
|
|
|
|
mxcmci_cfg.f_min = mxc_get_clock(MXC_ESDHC_CLK) >> 7;
|
|
mxcmci_cfg.f_max = mxc_get_clock(MXC_ESDHC_CLK) >> 1;
|
|
|
|
host->mmc = mmc_create(&mxcmci_cfg, host);
|
|
if (host->mmc == NULL)
|
|
return -1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int mxc_mmc_init(bd_t *bis)
|
|
{
|
|
return mxcmci_initialize(bis);
|
|
}
|