Jetpack/u-boot/include/configs/MPC8315ERDB.h

638 lines
19 KiB
C

/*
* Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
*
* Dave Liu <daveliu@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFE000000
#endif
#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
#define CONFIG_MPC831x 1 /* MPC831x CPU family */
#define CONFIG_MPC8315 1 /* MPC8315 CPU specific */
#define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */
/*
* System Clock Setup
*/
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
/*
* Hardware Reset Configuration Word
* if CLKIN is 66.66MHz, then
* CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_2X1 |\
HRCWL_SVCOD_DIV_2 |\
HRCWL_CSB_TO_CLKIN_2X1 |\
HRCWL_CORE_TO_CSB_3X1)
#define CONFIG_SYS_HRCW_HIGH_BASE (\
HRCWH_PCI_HOST |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_TSEC1M_IN_RGMII |\
HRCWH_TSEC2M_IN_RGMII |\
HRCWH_BIG_ENDIAN |\
HRCWH_LALE_NORMAL)
#ifdef CONFIG_NAND_SPL
#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
HRCWH_FROM_0XFFF00100 |\
HRCWH_ROM_LOC_NAND_SP_8BIT |\
HRCWH_RL_EXT_NAND)
#else
#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
HRCWH_FROM_0X00000100 |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_RL_EXT_LEGACY)
#endif
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH 0x00000000
#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
#define CONFIG_HWCONFIG
/*
* IMMR new address
*/
#define CONFIG_SYS_IMMR 0xE0000000
/*
* Arbiter Setup
*/
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
| DDRCDR_PZ_LOZ \
| DDRCDR_NZ_LOZ \
| DDRCDR_ODT \
| DDRCDR_Q_DRN)
/* 0x7b880001 */
/*
* Manually set up DDR parameters
* consist of two chips HY5PS12621BFP-C4 from HYNIX
*/
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
| CSCONFIG_ODT_RD_NEVER \
| CSCONFIG_ODT_WR_ONLY_CURRENT \
| CSCONFIG_ROW_BIT_13 \
| CSCONFIG_COL_BIT_10)
/* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
| (0 << TIMING_CFG0_WRT_SHIFT) \
| (0 << TIMING_CFG0_RRT_SHIFT) \
| (0 << TIMING_CFG0_WWT_SHIFT) \
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
/* 0x00220802 */
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
| (6 << TIMING_CFG1_REFREC_SHIFT) \
| (2 << TIMING_CFG1_WRREC_SHIFT) \
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
| (2 << TIMING_CFG1_WRTORD_SHIFT))
/* 0x27256222 */
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
| (4 << TIMING_CFG2_CPO_SHIFT) \
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
/* 0x121048c5 */
#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x03600100 */
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_DBW_32)
/* 0x43080000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
| (0x0232 << SDRAM_MODE_SD_SHIFT))
/* ODT 150ohm CL=3, AL=1 on SDRAM */
#define CONFIG_SYS_DDR_MODE2 0x00000000
/*
* Memory test
*/
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00140000
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00040000
#define CONFIG_FSL_ELBC 1
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \
| BR_PS_16 /* 16 bit port */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 \
| OR_GPCM_XACS \
| OR_GPCM_SCY_15 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EHTR_SET \
| OR_GPCM_EAD)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
/* 127 64KB sectors and 8 8KB top sectors per device */
#define CONFIG_SYS_MAX_FLASH_SECT 135
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/*
* NAND Flash on the Local Bus
*/
#ifdef CONFIG_NAND_SPL
#define CONFIG_SYS_NAND_BASE 0xFFF00000
#else
#define CONFIG_SYS_NAND_BASE 0xE0600000
#endif
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITION
#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nand0=e0600000.flash"
#define MTDPARTS_DEFAULT \
"mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)"
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_CMD_NAND 1
#define CONFIG_NAND_FSL_ELBC 1
#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
| BR_DECC_CHK_GEN /* Use HW ECC */ \
| BR_PS_8 /* 8 bit port */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_NAND_OR_PRELIM \
(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
| OR_FCM_CSCT \
| OR_FCM_CST \
| OR_FCM_CHT \
| OR_FCM_SCY_1 \
| OR_FCM_TRLX \
| OR_FCM_EHTR)
/* 0xFFFF8396 */
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
!defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Board info - revision and where boot from
*/
#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39
/*
* Config on-board RTC
*/
#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI_IO_BASE 0x00000000
#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
#define CONFIG_SYS_PCIE2_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_SCCR_USBDRCM 3
#define CONFIG_USB_STORAGE
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_PHY_TYPE "utmi"
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* TSEC
*/
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
/*
* TSEC ethernet configuration
*/
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME "eTSEC1"
/*
* SATA
*/
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1_OFFSET 0x18000
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2_OFFSET 0x19000
#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#ifdef CONFIG_FSL_SATA
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#endif
/*
* Environment
*/
#if !defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR \
(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#define CONFIG_CMD_DATE
#define CONFIG_CMD_PCI
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
HID0_ENABLE_INSTRUCTION_CACHE | \
HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
*/
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
| BATU_BL_128M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
| BATU_BL_8M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \
| BATU_BL_32M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR \
| BATU_BL_128K \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI_MEM_PHYS \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI_MEM_PHYS \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI_MMIO_PHYS \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI_MMIO_PHYS \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
#define CONFIG_SYS_IBAT6L 0
#define CONFIG_SYS_IBAT6U 0
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#define CONFIG_SYS_IBAT7L 0
#define CONFIG_SYS_IBAT7U 0
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#endif
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
"fdtaddr=780000\0" \
"fdtfile=mpc8315erdb.dtb\0" \
"usb_phy_type=utmi\0" \
""
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
"$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */