Jetpack/u-boot/board/gdsys/common/adv7611.c

178 lines
4.3 KiB
C

/*
* (C) Copyright 2014
* Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#define ADV7611_I2C_ADDR 0x4c
#define ADV7611_RDINFO 0x2051
/*
* ADV7611 I2C Addresses in u-boot notation
*/
enum {
CP_I2C_ADDR = 0x22,
DPLL_I2C_ADDR = 0x26,
KSV_I2C_ADDR = 0x32,
HDMI_I2C_ADDR = 0x34,
EDID_I2C_ADDR = 0x36,
INFOFRAME_I2C_ADDR = 0x3e,
CEC_I2C_ADDR = 0x40,
IO_I2C_ADDR = ADV7611_I2C_ADDR,
};
/*
* Global Control Registers
*/
enum {
IO_RD_INFO_MSB = 0xea,
IO_RD_INFO_LSB = 0xeb,
IO_CEC_ADDR = 0xf4,
IO_INFOFRAME_ADDR = 0xf5,
IO_DPLL_ADDR = 0xf8,
IO_KSV_ADDR = 0xf9,
IO_EDID_ADDR = 0xfa,
IO_HDMI_ADDR = 0xfb,
IO_CP_ADDR = 0xfd,
};
int adv7611_i2c[] = CONFIG_SYS_ADV7611_I2C;
int adv7611_probe(unsigned int screen)
{
int old_bus = i2c_get_bus_num();
unsigned int rd_info;
int res = 0;
i2c_set_bus_num(adv7611_i2c[screen]);
rd_info = (i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_MSB) << 8)
| i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_LSB);
if (rd_info != ADV7611_RDINFO) {
res = -1;
goto out;
}
/*
* set I2C addresses to default values
*/
i2c_reg_write(IO_I2C_ADDR, IO_CEC_ADDR, CEC_I2C_ADDR << 1);
i2c_reg_write(IO_I2C_ADDR, IO_INFOFRAME_ADDR, INFOFRAME_I2C_ADDR << 1);
i2c_reg_write(IO_I2C_ADDR, IO_DPLL_ADDR, DPLL_I2C_ADDR << 1);
i2c_reg_write(IO_I2C_ADDR, IO_KSV_ADDR, KSV_I2C_ADDR << 1);
i2c_reg_write(IO_I2C_ADDR, IO_EDID_ADDR, EDID_I2C_ADDR << 1);
i2c_reg_write(IO_I2C_ADDR, IO_HDMI_ADDR, HDMI_I2C_ADDR << 1);
i2c_reg_write(IO_I2C_ADDR, IO_CP_ADDR, CP_I2C_ADDR << 1);
/*
* do magic initialization sequence from
* "ADV7611 Register Settings Recommendations Revision 1.5"
* with most registers undocumented
*/
i2c_reg_write(CP_I2C_ADDR, 0x6c, 0x00);
i2c_reg_write(HDMI_I2C_ADDR, 0x9b, 0x03);
i2c_reg_write(HDMI_I2C_ADDR, 0x6f, 0x08);
i2c_reg_write(HDMI_I2C_ADDR, 0x85, 0x1f);
i2c_reg_write(HDMI_I2C_ADDR, 0x87, 0x70);
i2c_reg_write(HDMI_I2C_ADDR, 0x57, 0xda);
i2c_reg_write(HDMI_I2C_ADDR, 0x58, 0x01);
i2c_reg_write(HDMI_I2C_ADDR, 0x03, 0x98);
i2c_reg_write(HDMI_I2C_ADDR, 0x4c, 0x44);
/*
* IO_REG_02, default 0xf0
*
* INP_COLOR_SPACE (IO, Address 0x02[7:4])
* default: 0b1111 auto
* set to : 0b0001 force RGB (range 0 to 255) input
*
* RGB_OUT (IO, Address 0x02[1])
* default: 0 YPbPr color space output
* set to : 1 RGB color space output
*/
i2c_reg_write(IO_I2C_ADDR, 0x02, 0x12);
/*
* IO_REG_03, default 0x00
*
* OP_FORMAT_SEL (IO, Address 0x03[7:0])
* default: 0x00 8-bit SDR ITU-656 mode
* set to : 0x40 24-bit 4:4:4 SDR mode
*/
i2c_reg_write(IO_I2C_ADDR, 0x03, 0x40);
/*
* IO_REG_05, default 0x2c
*
* AVCODE_INSERT_EN (IO, Address 0x05[2])
* default: 1 insert AV codes into data stream
* set to : 0 do not insert AV codes into data stream
*/
i2c_reg_write(IO_I2C_ADDR, 0x05, 0x28);
/*
* IO_REG_0C, default 0x62
*
* POWER_DOWN (IO, Address 0x0C[5])
* default: 1 chip is powered down
* set to : 0 chip is operational
*/
i2c_reg_write(IO_I2C_ADDR, 0x0c, 0x42);
/*
* IO_REG_15, default 0xbe
*
* TRI_SYNCS (IO, Address 0x15[3)
* TRI_LLC (IO, Address 0x15[2])
* TRI_PIX (IO, Address 0x15[1])
* default: 1 video output pins are tristate
* set to : 0 video output pins are active
*/
i2c_reg_write(IO_I2C_ADDR, 0x15, 0xb0);
/*
* HDMI_REGISTER_02H, default 0xff
*
* CLOCK_TERMA_DISABLE (HDMI, Address 0x83[0])
* default: 1 disable termination
* set to : 0 enable termination
* Future options are:
* - use the chips automatic termination control
* - set this manually on cable detect
* but at the moment this seems a safe default.
*/
i2c_reg_write(HDMI_I2C_ADDR, 0x83, 0xfe);
/*
* HDMI_CP_CNTRL_1, default 0x01
*
* HDMI_FRUN_EN (CP, Address 0xBA[0])
* default: 1 Enable the free run feature in HDMI mode
* set to : 0 Disable the free run feature in HDMI mode
*/
i2c_reg_write(CP_I2C_ADDR, 0xba, 0x00);
/*
* INT1_CONFIGURATION, default 0x20
*
* INTRQ_DUR_SEL[1:0] (IO, Address 0x40[7:6])
* default: 00 Interrupt signal is active for 4 Xtal periods
* set to : 11 Active until cleared
*
* INTRQ_OP_SEL[1:0] (IO, Address 0x40[1:0])
* default: 00 Open drain
* set to : 10 Drives high when active
*/
i2c_reg_write(IO_I2C_ADDR, 0x40, 0xc2);
out:
i2c_set_bus_num(old_bus);
return res;
}