Jetpack/u-boot/board/amcc/yucca/yucca.c

715 lines
26 KiB
C

/*
* (C) Copyright 2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* Port to AMCC-440SPE Evaluation Board SOP - April 2005
*
* PCIe supporting routines derived from Linux 440SPe PCIe driver.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/ppc4xx.h>
#include <i2c.h>
#include <netdev.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/4xx_pcie.h>
#include <asm/errno.h>
#include "yucca.h"
DECLARE_GLOBAL_DATA_PTR;
void fpga_init (void);
#define DEBUG_ENV
#ifdef DEBUG_ENV
#define DEBUGF(fmt,args...) printf(fmt ,##args)
#else
#define DEBUGF(fmt,args...)
#endif
int board_early_init_f (void)
{
/*----------------------------------------------------------------------------+
| Define Boot devices
+----------------------------------------------------------------------------*/
#define BOOT_FROM_SMALL_FLASH 0x00
#define BOOT_FROM_LARGE_FLASH_OR_SRAM 0x01
#define BOOT_FROM_PCI 0x02
#define BOOT_DEVICE_UNKNOWN 0x03
/*----------------------------------------------------------------------------+
| EBC Devices Characteristics
| Peripheral Bank Access Parameters - EBC_BxAP
| Peripheral Bank Configuration Register - EBC_BxCR
+----------------------------------------------------------------------------*/
/*
* Small Flash and FRAM
* BU Value
* BxAP : 0x03800000 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000
* B0CR : 0xff098000 - BAS = ff0 - 100 11 00 0000000000000
* B2CR : 0xe7098000 - BAS = e70 - 100 11 00 0000000000000
*/
#define EBC_BXAP_SMALL_FLASH EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(7) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(0) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(0) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED
#define EBC_BXCR_SMALL_FLASH_CS0 EBC_BXCR_BAS_ENCODE(0xFF000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_8BIT
#define EBC_BXCR_SMALL_FLASH_CS2 EBC_BXCR_BAS_ENCODE(0xe7000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_8BIT
/*
* Large Flash and SRAM
* BU Value
* BxAP : 0x048ff240 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000
* B0CR : 0xff09a000 - BAS = ff0 - 100 11 01 0000000000000
* B2CR : 0xe709a000 - BAS = e70 - 100 11 01 0000000000000
*/
#define EBC_BXAP_LARGE_FLASH EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(7) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(0) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(0) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED
#define EBC_BXCR_LARGE_FLASH_CS0 EBC_BXCR_BAS_ENCODE(0xFF000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT
#define EBC_BXCR_LARGE_FLASH_CS2 EBC_BXCR_BAS_ENCODE(0xE7000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT
/*
* FPGA
* BU value :
* B1AP = 0x05895240 - 0 00001011 0 00 10 01 01 01 001 0 0 1 0 00000
* B1CR = 0xe201a000 - BAS = e20 - 000 11 01 00000000000000
*/
#define EBC_BXAP_FPGA EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(11) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(10) | \
EBC_BXAP_OEN_ENCODE(1) | \
EBC_BXAP_WBN_ENCODE(1) | \
EBC_BXAP_WBF_ENCODE(1) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED
#define EBC_BXCR_FPGA_CS1 EBC_BXCR_BAS_ENCODE(0xe2000000) | \
EBC_BXCR_BS_1MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT
unsigned long mfr;
/*
* Define Variables for EBC initialization depending on BOOTSTRAP option
*/
unsigned long sdr0_pinstp, sdr0_sdstp1 ;
unsigned long bootstrap_settings, ebc_data_width, boot_selection;
int computed_boot_device = BOOT_DEVICE_UNKNOWN;
/*-------------------------------------------------------------------+
| Initialize EBC CONFIG -
| Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
| default value :
| 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
|
+-------------------------------------------------------------------*/
mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE |
EBC_CFG_RTC_16PERCLK |
EBC_CFG_ATC_PREVIOUS |
EBC_CFG_DTC_PREVIOUS |
EBC_CFG_CTC_PREVIOUS |
EBC_CFG_OEO_PREVIOUS |
EBC_CFG_EMC_DEFAULT |
EBC_CFG_PME_DISABLE |
EBC_CFG_PR_16);
/*-------------------------------------------------------------------+
|
| PART 1 : Initialize EBC Bank 1
| ==============================
| Bank1 is always associated to the EPLD.
| It has to be initialized prior to other banks settings computation
| since some board registers values may be needed to determine the
| boot type
|
+-------------------------------------------------------------------*/
mtebc(PB1AP, EBC_BXAP_FPGA);
mtebc(PB1CR, EBC_BXCR_FPGA_CS1);
/*-------------------------------------------------------------------+
|
| PART 2 : Determine which boot device was selected
| =================================================
|
| Read Pin Strap Register in PPC440SPe
| Result can either be :
| - Boot strap = boot from EBC 8bits => Small Flash
| - Boot strap = boot from PCI
| - Boot strap = IIC
| In case of boot from IIC, read Serial Device Strap Register1
|
| Result can either be :
| - Boot from EBC - EBC Bus Width = 8bits => Small Flash
| - Boot from EBC - EBC Bus Width = 16bits => Large Flash or SRAM
| - Boot from PCI
|
+-------------------------------------------------------------------*/
/* Read Pin Strap Register in PPC440SP */
mfsdr(SDR0_PINSTP, sdr0_pinstp);
bootstrap_settings = sdr0_pinstp & SDR0_PINSTP_BOOTSTRAP_MASK;
switch (bootstrap_settings) {
case SDR0_PINSTP_BOOTSTRAP_SETTINGS0:
/*
* Strapping Option A
* Boot from EBC - 8 bits , Small Flash
*/
computed_boot_device = BOOT_FROM_SMALL_FLASH;
break;
case SDR0_PINSTP_BOOTSTRAP_SETTINGS1:
/*
* Strappping Option B
* Boot from PCI
*/
computed_boot_device = BOOT_FROM_PCI;
break;
case SDR0_PINSTP_BOOTSTRAP_IIC_50_EN:
case SDR0_PINSTP_BOOTSTRAP_IIC_54_EN:
/*
* Strapping Option C or D
* Boot Settings in IIC EEprom address 0x50 or 0x54
* Read Serial Device Strap Register1 in PPC440SPe
*/
mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_ERPN_MASK;
ebc_data_width = sdr0_sdstp1 & SDR0_SDSTP1_EBCW_MASK;
switch (boot_selection) {
case SDR0_SDSTP1_ERPN_EBC:
switch (ebc_data_width) {
case SDR0_SDSTP1_EBCW_16_BITS:
computed_boot_device =
BOOT_FROM_LARGE_FLASH_OR_SRAM;
break;
case SDR0_SDSTP1_EBCW_8_BITS :
computed_boot_device = BOOT_FROM_SMALL_FLASH;
break;
}
break;
case SDR0_SDSTP1_ERPN_PCI:
computed_boot_device = BOOT_FROM_PCI;
break;
default:
/* should not occure */
computed_boot_device = BOOT_DEVICE_UNKNOWN;
}
break;
default:
/* should not be */
computed_boot_device = BOOT_DEVICE_UNKNOWN;
break;
}
/*-------------------------------------------------------------------+
|
| PART 3 : Compute EBC settings depending on selected boot device
| ====== ======================================================
|
| Resulting EBC init will be among following configurations :
|
| - Boot from EBC 8bits => boot from Small Flash selected
| EBC-CS0 = Small Flash
| EBC-CS2 = Large Flash and SRAM
|
| - Boot from EBC 16bits => boot from Large Flash or SRAM
| EBC-CS0 = Large Flash or SRAM
| EBC-CS2 = Small Flash
|
| - Boot from PCI
| EBC-CS0 = not initialized to avoid address contention
| EBC-CS2 = same as boot from Small Flash selected
|
+-------------------------------------------------------------------*/
unsigned long ebc0_cs0_bxap_value = 0, ebc0_cs0_bxcr_value = 0;
unsigned long ebc0_cs2_bxap_value = 0, ebc0_cs2_bxcr_value = 0;
switch (computed_boot_device) {
/*-------------------------------------------------------------------*/
case BOOT_FROM_PCI:
/*-------------------------------------------------------------------*/
/*
* By Default CS2 is affected to LARGE Flash
* do not initialize SMALL FLASH to avoid address contention
* Large Flash
*/
ebc0_cs2_bxap_value = EBC_BXAP_LARGE_FLASH;
ebc0_cs2_bxcr_value = EBC_BXCR_LARGE_FLASH_CS2;
break;
/*-------------------------------------------------------------------*/
case BOOT_FROM_SMALL_FLASH:
/*-------------------------------------------------------------------*/
ebc0_cs0_bxap_value = EBC_BXAP_SMALL_FLASH;
ebc0_cs0_bxcr_value = EBC_BXCR_SMALL_FLASH_CS0;
/*
* Large Flash or SRAM
*/
/* ebc0_cs2_bxap_value = EBC_BXAP_LARGE_FLASH; */
ebc0_cs2_bxap_value = 0x048ff240;
ebc0_cs2_bxcr_value = EBC_BXCR_LARGE_FLASH_CS2;
break;
/*-------------------------------------------------------------------*/
case BOOT_FROM_LARGE_FLASH_OR_SRAM:
/*-------------------------------------------------------------------*/
ebc0_cs0_bxap_value = EBC_BXAP_LARGE_FLASH;
ebc0_cs0_bxcr_value = EBC_BXCR_LARGE_FLASH_CS0;
/* Small flash */
ebc0_cs2_bxap_value = EBC_BXAP_SMALL_FLASH;
ebc0_cs2_bxcr_value = EBC_BXCR_SMALL_FLASH_CS2;
break;
/*-------------------------------------------------------------------*/
default:
/*-------------------------------------------------------------------*/
/* BOOT_DEVICE_UNKNOWN */
break;
}
mtebc(PB0AP, ebc0_cs0_bxap_value);
mtebc(PB0CR, ebc0_cs0_bxcr_value);
mtebc(PB2AP, ebc0_cs2_bxap_value);
mtebc(PB2CR, ebc0_cs2_bxcr_value);
/*--------------------------------------------------------------------+
| Interrupt controller setup for the AMCC 440SPe Evaluation board.
+--------------------------------------------------------------------+
+---------------------------------------------------------------------+
|Interrupt| Source | Pol. | Sensi.| Crit. |
+---------+-----------------------------------+-------+-------+-------+
| IRQ 00 | UART0 | High | Level | Non |
| IRQ 01 | UART1 | High | Level | Non |
| IRQ 02 | IIC0 | High | Level | Non |
| IRQ 03 | IIC1 | High | Level | Non |
| IRQ 04 | PCI0X0 MSG IN | High | Level | Non |
| IRQ 05 | PCI0X0 CMD Write | High | Level | Non |
| IRQ 06 | PCI0X0 Power Mgt | High | Level | Non |
| IRQ 07 | PCI0X0 VPD Access | Rising| Edge | Non |
| IRQ 08 | PCI0X0 MSI level 0 | High | Lvl/ed| Non |
| IRQ 09 | External IRQ 15 - (PCI-Express) | pgm H | Pgm | Non |
| IRQ 10 | UIC2 Non-critical Int. | NA | NA | Non |
| IRQ 11 | UIC2 Critical Interrupt | NA | NA | Crit |
| IRQ 12 | PCI Express MSI Level 0 | Rising| Edge | Non |
| IRQ 13 | PCI Express MSI Level 1 | Rising| Edge | Non |
| IRQ 14 | PCI Express MSI Level 2 | Rising| Edge | Non |
| IRQ 15 | PCI Express MSI Level 3 | Rising| Edge | Non |
| IRQ 16 | UIC3 Non-critical Int. | NA | NA | Non |
| IRQ 17 | UIC3 Critical Interrupt | NA | NA | Crit |
| IRQ 18 | External IRQ 14 - (PCI-Express) | Pgm | Pgm | Non |
| IRQ 19 | DMA Channel 0 FIFO Full | High | Level | Non |
| IRQ 20 | DMA Channel 0 Stat FIFO | High | Level | Non |
| IRQ 21 | DMA Channel 1 FIFO Full | High | Level | Non |
| IRQ 22 | DMA Channel 1 Stat FIFO | High | Level | Non |
| IRQ 23 | I2O Inbound Doorbell | High | Level | Non |
| IRQ 24 | Inbound Post List FIFO Not Empt | High | Level | Non |
| IRQ 25 | I2O Region 0 LL PLB Write | High | Level | Non |
| IRQ 26 | I2O Region 1 LL PLB Write | High | Level | Non |
| IRQ 27 | I2O Region 0 HB PLB Write | High | Level | Non |
| IRQ 28 | I2O Region 1 HB PLB Write | High | Level | Non |
| IRQ 29 | GPT Down Count Timer | Rising| Edge | Non |
| IRQ 30 | UIC1 Non-critical Int. | NA | NA | Non |
| IRQ 31 | UIC1 Critical Interrupt | NA | NA | Crit. |
|----------------------------------------------------------------------
| IRQ 32 | Ext. IRQ 13 - (PCI-Express) |pgm (H)|pgm/Lvl| Non |
| IRQ 33 | MAL Serr | High | Level | Non |
| IRQ 34 | MAL Txde | High | Level | Non |
| IRQ 35 | MAL Rxde | High | Level | Non |
| IRQ 36 | DMC CE or DMC UE | High | Level | Non |
| IRQ 37 | EBC or UART2 | High |Lvl Edg| Non |
| IRQ 38 | MAL TX EOB | High | Level | Non |
| IRQ 39 | MAL RX EOB | High | Level | Non |
| IRQ 40 | PCIX0 MSI Level 1 | High |Lvl Edg| Non |
| IRQ 41 | PCIX0 MSI level 2 | High |Lvl Edg| Non |
| IRQ 42 | PCIX0 MSI level 3 | High |Lvl Edg| Non |
| IRQ 43 | L2 Cache | Risin | Edge | Non |
| IRQ 44 | GPT Compare Timer 0 | Risin | Edge | Non |
| IRQ 45 | GPT Compare Timer 1 | Risin | Edge | Non |
| IRQ 46 | GPT Compare Timer 2 | Risin | Edge | Non |
| IRQ 47 | GPT Compare Timer 3 | Risin | Edge | Non |
| IRQ 48 | GPT Compare Timer 4 | Risin | Edge | Non |
| IRQ 49 | Ext. IRQ 12 - PCI-X |pgm/Fal|pgm/Lvl| Non |
| IRQ 50 | Ext. IRQ 11 - |pgm (H)|pgm/Lvl| Non |
| IRQ 51 | Ext. IRQ 10 - |pgm (H)|pgm/Lvl| Non |
| IRQ 52 | Ext. IRQ 9 |pgm (H)|pgm/Lvl| Non |
| IRQ 53 | Ext. IRQ 8 |pgm (H)|pgm/Lvl| Non |
| IRQ 54 | DMA Error | High | Level | Non |
| IRQ 55 | DMA I2O Error | High | Level | Non |
| IRQ 56 | Serial ROM | High | Level | Non |
| IRQ 57 | PCIX0 Error | High | Edge | Non |
| IRQ 58 | Ext. IRQ 7- |pgm (H)|pgm/Lvl| Non |
| IRQ 59 | Ext. IRQ 6- |pgm (H)|pgm/Lvl| Non |
| IRQ 60 | EMAC0 Interrupt | High | Level | Non |
| IRQ 61 | EMAC0 Wake-up | High | Level | Non |
| IRQ 62 | Reserved | High | Level | Non |
| IRQ 63 | XOR | High | Level | Non |
|----------------------------------------------------------------------
| IRQ 64 | PE0 AL | High | Level | Non |
| IRQ 65 | PE0 VPD Access | Risin | Edge | Non |
| IRQ 66 | PE0 Hot Reset Request | Risin | Edge | Non |
| IRQ 67 | PE0 Hot Reset Request | Falli | Edge | Non |
| IRQ 68 | PE0 TCR | High | Level | Non |
| IRQ 69 | PE0 BusMaster VCO | Falli | Edge | Non |
| IRQ 70 | PE0 DCR Error | High | Level | Non |
| IRQ 71 | Reserved | N/A | N/A | Non |
| IRQ 72 | PE1 AL | High | Level | Non |
| IRQ 73 | PE1 VPD Access | Risin | Edge | Non |
| IRQ 74 | PE1 Hot Reset Request | Risin | Edge | Non |
| IRQ 75 | PE1 Hot Reset Request | Falli | Edge | Non |
| IRQ 76 | PE1 TCR | High | Level | Non |
| IRQ 77 | PE1 BusMaster VCO | Falli | Edge | Non |
| IRQ 78 | PE1 DCR Error | High | Level | Non |
| IRQ 79 | Reserved | N/A | N/A | Non |
| IRQ 80 | PE2 AL | High | Level | Non |
| IRQ 81 | PE2 VPD Access | Risin | Edge | Non |
| IRQ 82 | PE2 Hot Reset Request | Risin | Edge | Non |
| IRQ 83 | PE2 Hot Reset Request | Falli | Edge | Non |
| IRQ 84 | PE2 TCR | High | Level | Non |
| IRQ 85 | PE2 BusMaster VCO | Falli | Edge | Non |
| IRQ 86 | PE2 DCR Error | High | Level | Non |
| IRQ 87 | Reserved | N/A | N/A | Non |
| IRQ 88 | External IRQ(5) | Progr | Progr | Non |
| IRQ 89 | External IRQ 4 - Ethernet | Progr | Progr | Non |
| IRQ 90 | External IRQ 3 - PCI-X | Progr | Progr | Non |
| IRQ 91 | External IRQ 2 - PCI-X | Progr | Progr | Non |
| IRQ 92 | External IRQ 1 - PCI-X | Progr | Progr | Non |
| IRQ 93 | External IRQ 0 - PCI-X | Progr | Progr | Non |
| IRQ 94 | Reserved | N/A | N/A | Non |
| IRQ 95 | Reserved | N/A | N/A | Non |
|---------------------------------------------------------------------
| IRQ 96 | PE0 INTA | High | Level | Non |
| IRQ 97 | PE0 INTB | High | Level | Non |
| IRQ 98 | PE0 INTC | High | Level | Non |
| IRQ 99 | PE0 INTD | High | Level | Non |
| IRQ 100 | PE1 INTA | High | Level | Non |
| IRQ 101 | PE1 INTB | High | Level | Non |
| IRQ 102 | PE1 INTC | High | Level | Non |
| IRQ 103 | PE1 INTD | High | Level | Non |
| IRQ 104 | PE2 INTA | High | Level | Non |
| IRQ 105 | PE2 INTB | High | Level | Non |
| IRQ 106 | PE2 INTC | High | Level | Non |
| IRQ 107 | PE2 INTD | Risin | Edge | Non |
| IRQ 108 | PCI Express MSI Level 4 | Risin | Edge | Non |
| IRQ 109 | PCI Express MSI Level 5 | Risin | Edge | Non |
| IRQ 110 | PCI Express MSI Level 6 | Risin | Edge | Non |
| IRQ 111 | PCI Express MSI Level 7 | Risin | Edge | Non |
| IRQ 116 | PCI Express MSI Level 12 | Risin | Edge | Non |
| IRQ 112 | PCI Express MSI Level 8 | Risin | Edge | Non |
| IRQ 113 | PCI Express MSI Level 9 | Risin | Edge | Non |
| IRQ 114 | PCI Express MSI Level 10 | Risin | Edge | Non |
| IRQ 115 | PCI Express MSI Level 11 | Risin | Edge | Non |
| IRQ 117 | PCI Express MSI Level 13 | Risin | Edge | Non |
| IRQ 118 | PCI Express MSI Level 14 | Risin | Edge | Non |
| IRQ 119 | PCI Express MSI Level 15 | Risin | Edge | Non |
| IRQ 120 | PCI Express MSI Level 16 | Risin | Edge | Non |
| IRQ 121 | PCI Express MSI Level 17 | Risin | Edge | Non |
| IRQ 122 | PCI Express MSI Level 18 | Risin | Edge | Non |
| IRQ 123 | PCI Express MSI Level 19 | Risin | Edge | Non |
| IRQ 124 | PCI Express MSI Level 20 | Risin | Edge | Non |
| IRQ 125 | PCI Express MSI Level 21 | Risin | Edge | Non |
| IRQ 126 | PCI Express MSI Level 22 | Risin | Edge | Non |
| IRQ 127 | PCI Express MSI Level 23 | Risin | Edge | Non |
+---------+-----------------------------------+-------+-------+------*/
/*--------------------------------------------------------------------+
| Put UICs in PowerPC440SPemode.
| Initialise UIC registers. Clear all interrupts. Disable all
| interrupts.
| Set critical interrupt values. Set interrupt polarities. Set
| interrupt trigger levels. Make bit 0 High priority. Clear all
| interrupts again.
+-------------------------------------------------------------------*/
mtdcr (UIC3SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC3ER, 0x00000000); /* disable all interrupts */
mtdcr (UIC3CR, 0x00000000); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC3PR, 0xffffffff); /* Set Interrupt Polarities */
mtdcr (UIC3TR, 0x001fffff); /* Set Interrupt Trigger Levels */
mtdcr (UIC3VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC3SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC3SR, 0xffffffff); /* clear all interrupts */
mtdcr (UIC2SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC2ER, 0x00000000); /* disable all interrupts */
mtdcr (UIC2CR, 0x00000000); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC2PR, 0xebebebff); /* Set Interrupt Polarities */
mtdcr (UIC2TR, 0x74747400); /* Set Interrupt Trigger Levels */
mtdcr (UIC2VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC2SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC2SR, 0xffffffff); /* clear all interrupts */
mtdcr (UIC1SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC1ER, 0x00000000); /* disable all interrupts */
mtdcr (UIC1CR, 0x00000000); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC1PR, 0xffffffff); /* Set Interrupt Polarities */
mtdcr (UIC1TR, 0x001f8040); /* Set Interrupt Trigger Levels */
mtdcr (UIC1VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC1SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC1SR, 0xffffffff); /* clear all interrupts */
mtdcr (UIC0SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC0ER, 0x00000000); /* disable all interrupts excepted
* cascade to be checked */
mtdcr (UIC0CR, 0x00104001); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC0PR, 0xffffffff); /* Set Interrupt Polarities */
mtdcr (UIC0TR, 0x010f0004); /* Set Interrupt Trigger Levels */
mtdcr (UIC0VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC0SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC0SR, 0xffffffff); /* clear all interrupts */
mfsdr(SDR0_MFR, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
mtsdr(SDR0_MFR, mfr);
fpga_init();
return 0;
}
int checkboard (void)
{
char buf[64];
int i = getenv_f("serial#", buf, sizeof(buf));
printf("Board: Yucca - AMCC 440SPe Evaluation Board");
if (i > 0) {
puts(", serial# ");
puts(buf);
}
putc('\n');
return 0;
}
/*
* Override the default functions in arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c with
* board specific values.
*/
static int ppc440spe_rev_a(void)
{
if ((get_pvr() == PVR_440SPe_6_RA) || (get_pvr() == PVR_440SPe_RA))
return 1;
else
return 0;
}
u32 ddr_wrdtr(u32 default_val) {
/*
* Yucca boards with 440SPe rev. A need a slightly different setup
* for the MCIF0_WRDTR register.
*/
if (ppc440spe_rev_a())
return (SDRAM_WRDTR_LLWP_1_CYC | SDRAM_WRDTR_WTR_270_DEG_ADV);
return default_val;
}
u32 ddr_clktr(u32 default_val) {
/*
* Yucca boards with 440SPe rev. A need a slightly different setup
* for the MCIF0_CLKTR register.
*/
if (ppc440spe_rev_a())
return (SDRAM_CLKTR_CLKP_180_DEG_ADV);
return default_val;
}
#if defined(CONFIG_PCI)
int board_pcie_card_present(int port)
{
u16 reg;
reg = in_be16((u16 *)FPGA_REG1C);
switch(port) {
case 0:
return !(reg & FPGA_REG1C_PE0_PRSNT);
case 1:
return !(reg & FPGA_REG1C_PE1_PRSNT);
case 2:
return !(reg & FPGA_REG1C_PE2_PRSNT);
default:
return 0;
}
}
/*
* For the given slot, set endpoint mode, send power to the slot,
* turn on the green LED and turn off the yellow LED, enable the
* clock. In endpoint mode reset bit is read only.
*/
void board_pcie_setup_port(int port, int rootpoint)
{
u16 power, clock, green_led, yellow_led,
reset_off, rp, ep;
switch (port) {
case 0:
rp = FPGA_REG1C_PE0_ROOTPOINT;
ep = 0;
break;
case 1:
rp = 0;
ep = FPGA_REG1C_PE1_ENDPOINT;
break;
case 2:
rp = 0;
ep = FPGA_REG1C_PE2_ENDPOINT;
break;
default:
return;
}
power = FPGA_REG1A_PWRON_ENCODE(port);
green_led = FPGA_REG1A_GLED_ENCODE(port);
clock = FPGA_REG1A_REFCLK_ENCODE(port);
yellow_led = FPGA_REG1A_YLED_ENCODE(port);
reset_off = FPGA_REG1C_PERST_ENCODE(port);
out_be16((u16 *)FPGA_REG1A, ~(power | clock | green_led) &
(yellow_led | in_be16((u16 *)FPGA_REG1A)));
out_be16((u16 *)FPGA_REG1C, ~(ep | reset_off) &
(rp | in_be16((u16 *)FPGA_REG1C)));
if (rootpoint) {
/*
* Leave device in reset for a while after powering on the
* slot to give it a chance to initialize.
*/
udelay(250 * 1000);
out_be16((u16 *)FPGA_REG1C,
reset_off | in_be16((u16 *)FPGA_REG1C));
}
}
#endif /* defined(CONFIG_PCI) */
int misc_init_f (void)
{
uint reg;
out16(FPGA_REG10, (in16(FPGA_REG10) &
~(FPGA_REG10_AUTO_NEG_DIS|FPGA_REG10_RESET_ETH)) |
FPGA_REG10_10MHZ_ENABLE |
FPGA_REG10_100MHZ_ENABLE |
FPGA_REG10_GIGABIT_ENABLE |
FPGA_REG10_FULL_DUPLEX );
udelay(10000); /* wait 10ms */
out16(FPGA_REG10, (in16(FPGA_REG10) | FPGA_REG10_RESET_ETH));
/* minimal init for PCIe */
/* pci express 0 Endpoint Mode */
mfsdr(SDRN_PESDR_DLPSET(0), reg);
reg &= (~0x00400000);
mtsdr(SDRN_PESDR_DLPSET(0), reg);
/* pci express 1 Rootpoint Mode */
mfsdr(SDRN_PESDR_DLPSET(1), reg);
reg |= 0x00400000;
mtsdr(SDRN_PESDR_DLPSET(1), reg);
/* pci express 2 Rootpoint Mode */
mfsdr(SDRN_PESDR_DLPSET(2), reg);
reg |= 0x00400000;
mtsdr(SDRN_PESDR_DLPSET(2), reg);
out16(FPGA_REG1C,(in16 (FPGA_REG1C) &
~FPGA_REG1C_PE0_ROOTPOINT &
~FPGA_REG1C_PE1_ENDPOINT &
~FPGA_REG1C_PE2_ENDPOINT));
return 0;
}
void fpga_init(void)
{
/*
* by default sdram access is disabled by fpga
*/
out16(FPGA_REG10, (in16 (FPGA_REG10) |
FPGA_REG10_SDRAM_ENABLE |
FPGA_REG10_ENABLE_DISPLAY ));
return;
}
/*---------------------------------------------------------------------------+
| onboard_pci_arbiter_selected => from EPLD
+---------------------------------------------------------------------------*/
int onboard_pci_arbiter_selected(int core_pci)
{
#if 0
unsigned long onboard_pci_arbiter_sel;
onboard_pci_arbiter_sel = in16(FPGA_REG0) & FPGA_REG0_EXT_ARB_SEL_MASK;
if (onboard_pci_arbiter_sel == FPGA_REG0_EXT_ARB_SEL_EXTERNAL)
return (BOARD_OPTION_SELECTED);
else
#endif
return (BOARD_OPTION_NOT_SELECTED);
}
int board_eth_init(bd_t *bis)
{
cpu_eth_init(bis);
return pci_eth_init(bis);
}