forked from rrcarlosr/Jetpack
166 lines
6.8 KiB
C
166 lines
6.8 KiB
C
/*
|
|
* SPI device spec header file
|
|
*
|
|
* Copyright (C) 1999-2015, Broadcom Corporation
|
|
*
|
|
* Unless you and Broadcom execute a separate written software license
|
|
* agreement governing use of this software, this software is licensed to you
|
|
* under the terms of the GNU General Public License version 2 (the "GPL"),
|
|
* available at http://www.broadcom.com/licenses/GPLv2.php, with the
|
|
* following added to such license:
|
|
*
|
|
* As a special exception, the copyright holders of this software give you
|
|
* permission to link this software with independent modules, and to copy and
|
|
* distribute the resulting executable under terms of your choice, provided that
|
|
* you also meet, for each linked independent module, the terms and conditions of
|
|
* the license of that module. An independent module is a module which is not
|
|
* derived from this software. The special exception does not apply to any
|
|
* modifications of the software.
|
|
*
|
|
* Notwithstanding the above, under no circumstances may you combine this
|
|
* software in any way with any other Broadcom software provided under a license
|
|
* other than the GPL, without Broadcom's express prior written consent.
|
|
*
|
|
* $Id: spid.h 358377 2012-09-23 11:30:22Z $
|
|
*/
|
|
|
|
#ifndef _SPI_H
|
|
#define _SPI_H
|
|
|
|
/*
|
|
* Brcm SPI Device Register Map.
|
|
*
|
|
*/
|
|
|
|
typedef volatile struct {
|
|
uint8 config; /* 0x00, len, endian, clock, speed, polarity, wakeup */
|
|
uint8 response_delay; /* 0x01, read response delay in bytes (corerev < 3) */
|
|
uint8 status_enable; /* 0x02, status-enable, intr with status, response_delay
|
|
* function selection, command/data error check
|
|
*/
|
|
uint8 reset_bp; /* 0x03, reset on wlan/bt backplane reset (corerev >= 1) */
|
|
uint16 intr_reg; /* 0x04, Intr status register */
|
|
uint16 intr_en_reg; /* 0x06, Intr mask register */
|
|
uint32 status_reg; /* 0x08, RO, Status bits of last spi transfer */
|
|
uint16 f1_info_reg; /* 0x0c, RO, enabled, ready for data transfer, blocksize */
|
|
uint16 f2_info_reg; /* 0x0e, RO, enabled, ready for data transfer, blocksize */
|
|
uint16 f3_info_reg; /* 0x10, RO, enabled, ready for data transfer, blocksize */
|
|
uint32 test_read; /* 0x14, RO 0xfeedbead signature */
|
|
uint32 test_rw; /* 0x18, RW */
|
|
uint8 resp_delay_f0; /* 0x1c, read resp delay bytes for F0 (corerev >= 3) */
|
|
uint8 resp_delay_f1; /* 0x1d, read resp delay bytes for F1 (corerev >= 3) */
|
|
uint8 resp_delay_f2; /* 0x1e, read resp delay bytes for F2 (corerev >= 3) */
|
|
uint8 resp_delay_f3; /* 0x1f, read resp delay bytes for F3 (corerev >= 3) */
|
|
} spi_regs_t;
|
|
|
|
/* SPI device register offsets */
|
|
#define SPID_CONFIG 0x00
|
|
#define SPID_RESPONSE_DELAY 0x01
|
|
#define SPID_STATUS_ENABLE 0x02
|
|
#define SPID_RESET_BP 0x03 /* (corerev >= 1) */
|
|
#define SPID_INTR_REG 0x04 /* 16 bits - Interrupt status */
|
|
#define SPID_INTR_EN_REG 0x06 /* 16 bits - Interrupt mask */
|
|
#define SPID_STATUS_REG 0x08 /* 32 bits */
|
|
#define SPID_F1_INFO_REG 0x0C /* 16 bits */
|
|
#define SPID_F2_INFO_REG 0x0E /* 16 bits */
|
|
#define SPID_F3_INFO_REG 0x10 /* 16 bits */
|
|
#define SPID_TEST_READ 0x14 /* 32 bits */
|
|
#define SPID_TEST_RW 0x18 /* 32 bits */
|
|
#define SPID_RESP_DELAY_F0 0x1c /* 8 bits (corerev >= 3) */
|
|
#define SPID_RESP_DELAY_F1 0x1d /* 8 bits (corerev >= 3) */
|
|
#define SPID_RESP_DELAY_F2 0x1e /* 8 bits (corerev >= 3) */
|
|
#define SPID_RESP_DELAY_F3 0x1f /* 8 bits (corerev >= 3) */
|
|
|
|
/* Bit masks for SPID_CONFIG device register */
|
|
#define WORD_LENGTH_32 0x1 /* 0/1 16/32 bit word length */
|
|
#define ENDIAN_BIG 0x2 /* 0/1 Little/Big Endian */
|
|
#define CLOCK_PHASE 0x4 /* 0/1 clock phase delay */
|
|
#define CLOCK_POLARITY 0x8 /* 0/1 Idle state clock polarity is low/high */
|
|
#define HIGH_SPEED_MODE 0x10 /* 1/0 High Speed mode / Normal mode */
|
|
#define INTR_POLARITY 0x20 /* 1/0 Interrupt active polarity is high/low */
|
|
#define WAKE_UP 0x80 /* 0/1 Wake-up command from Host to WLAN */
|
|
|
|
/* Bit mask for SPID_RESPONSE_DELAY device register */
|
|
#define RESPONSE_DELAY_MASK 0xFF /* Configurable rd response delay in multiples of 8 bits */
|
|
|
|
/* Bit mask for SPID_STATUS_ENABLE device register */
|
|
#define STATUS_ENABLE 0x1 /* 1/0 Status sent/not sent to host after read/write */
|
|
#define INTR_WITH_STATUS 0x2 /* 0/1 Do-not / do-interrupt if status is sent */
|
|
#define RESP_DELAY_ALL 0x4 /* Applicability of resp delay to F1 or all func's read */
|
|
#define DWORD_PKT_LEN_EN 0x8 /* Packet len denoted in dwords instead of bytes */
|
|
#define CMD_ERR_CHK_EN 0x20 /* Command error check enable */
|
|
#define DATA_ERR_CHK_EN 0x40 /* Data error check enable */
|
|
|
|
/* Bit mask for SPID_RESET_BP device register */
|
|
#define RESET_ON_WLAN_BP_RESET 0x4 /* enable reset for WLAN backplane */
|
|
#define RESET_ON_BT_BP_RESET 0x8 /* enable reset for BT backplane */
|
|
#define RESET_SPI 0x80 /* reset the above enabled logic */
|
|
|
|
/* Bit mask for SPID_INTR_REG device register */
|
|
#define DATA_UNAVAILABLE 0x0001 /* Requested data not available; Clear by writing a "1" */
|
|
#define F2_F3_FIFO_RD_UNDERFLOW 0x0002
|
|
#define F2_F3_FIFO_WR_OVERFLOW 0x0004
|
|
#define COMMAND_ERROR 0x0008 /* Cleared by writing 1 */
|
|
#define DATA_ERROR 0x0010 /* Cleared by writing 1 */
|
|
#define F2_PACKET_AVAILABLE 0x0020
|
|
#define F3_PACKET_AVAILABLE 0x0040
|
|
#define F1_OVERFLOW 0x0080 /* Due to last write. Bkplane has pending write requests */
|
|
#define MISC_INTR0 0x0100
|
|
#define MISC_INTR1 0x0200
|
|
#define MISC_INTR2 0x0400
|
|
#define MISC_INTR3 0x0800
|
|
#define MISC_INTR4 0x1000
|
|
#define F1_INTR 0x2000
|
|
#define F2_INTR 0x4000
|
|
#define F3_INTR 0x8000
|
|
|
|
/* Bit mask for 32bit SPID_STATUS_REG device register */
|
|
#define STATUS_DATA_NOT_AVAILABLE 0x00000001
|
|
#define STATUS_UNDERFLOW 0x00000002
|
|
#define STATUS_OVERFLOW 0x00000004
|
|
#define STATUS_F2_INTR 0x00000008
|
|
#define STATUS_F3_INTR 0x00000010
|
|
#define STATUS_F2_RX_READY 0x00000020
|
|
#define STATUS_F3_RX_READY 0x00000040
|
|
#define STATUS_HOST_CMD_DATA_ERR 0x00000080
|
|
#define STATUS_F2_PKT_AVAILABLE 0x00000100
|
|
#define STATUS_F2_PKT_LEN_MASK 0x000FFE00
|
|
#define STATUS_F2_PKT_LEN_SHIFT 9
|
|
#define STATUS_F3_PKT_AVAILABLE 0x00100000
|
|
#define STATUS_F3_PKT_LEN_MASK 0xFFE00000
|
|
#define STATUS_F3_PKT_LEN_SHIFT 21
|
|
|
|
/* Bit mask for 16 bits SPID_F1_INFO_REG device register */
|
|
#define F1_ENABLED 0x0001
|
|
#define F1_RDY_FOR_DATA_TRANSFER 0x0002
|
|
#define F1_MAX_PKT_SIZE 0x01FC
|
|
|
|
/* Bit mask for 16 bits SPID_F2_INFO_REG device register */
|
|
#define F2_ENABLED 0x0001
|
|
#define F2_RDY_FOR_DATA_TRANSFER 0x0002
|
|
#define F2_MAX_PKT_SIZE 0x3FFC
|
|
|
|
/* Bit mask for 16 bits SPID_F3_INFO_REG device register */
|
|
#define F3_ENABLED 0x0001
|
|
#define F3_RDY_FOR_DATA_TRANSFER 0x0002
|
|
#define F3_MAX_PKT_SIZE 0x3FFC
|
|
|
|
/* Bit mask for 32 bits SPID_TEST_READ device register read in 16bit LE mode */
|
|
#define TEST_RO_DATA_32BIT_LE 0xFEEDBEAD
|
|
|
|
/* Maximum number of I/O funcs */
|
|
#define SPI_MAX_IOFUNCS 4
|
|
|
|
#define SPI_MAX_PKT_LEN (2048*4)
|
|
|
|
/* Misc defines */
|
|
#define SPI_FUNC_0 0
|
|
#define SPI_FUNC_1 1
|
|
#define SPI_FUNC_2 2
|
|
#define SPI_FUNC_3 3
|
|
|
|
#define WAIT_F2RXFIFORDY 100
|
|
#define WAIT_F2RXFIFORDY_DELAY 20
|
|
|
|
#endif /* _SPI_H */
|