forked from rrcarlosr/Jetpack
73 lines
2.9 KiB
Plaintext
73 lines
2.9 KiB
Plaintext
* NVIDIA Tegra, Universal Flash Storage (UFS) Host Controller
|
|
|
|
UFSHC nodes are defined to describe on-chip UFS host controllers.
|
|
Each UFS controller instance should have its own node.
|
|
|
|
Required properties:
|
|
- compatible : compatible list, contains "jedec,ufs-1.1"
|
|
- interrupts : <interrupt mapping for UFS host controller IRQ>
|
|
- reg : <registers mapping>
|
|
|
|
Optional properties:
|
|
- clocks : List of phandle and clock specifier pairs
|
|
- clock-names : List of clock input name strings sorted in the same
|
|
order as the clocks property.
|
|
- freq-table-hz : Array of <min max> operating frequencies stored in the same
|
|
order as the clocks property. If this property is not
|
|
defined or a value in the array is "0" then it is assumed
|
|
that the frequency is set by the parent clock or a
|
|
fixed rate clock source.
|
|
|
|
- nvidia,configure-uphy-pll3 : Provides an option to configure uphy_pll3 for
|
|
ufs rate_a and rate_b modes.
|
|
|
|
- nvidia,enable-scramble : Enables scramble functionality.
|
|
It is required to enable scramble functionality, which is used for
|
|
encryption.
|
|
- nvidia,enable-rx-calib : Enables rx calibration functionality.
|
|
It is required for UFS High Speed modes.
|
|
- nvidia,enable-x2-config : Enables 2 lane register programming support.
|
|
Should be enabled if 2 lanes are dedicated to UFS.
|
|
- nvidia,enable-hs-mode : Flag to enable UFS High Speed modes. If this flag is not set
|
|
UFS will be enumerated in PWM mode.
|
|
- nvidia,mask-fast-auto-mode : Flag to disable fast auto mode.
|
|
When enabled UFS Fast auto mode will not be supported and
|
|
fast mode will be supported.
|
|
- nvidia,mask-hs-mode-b : Flag to disable hs_rate_b series.
|
|
When enabled UFS hs_rate_b series will not be supported and
|
|
hs_rate_a series will be supported.
|
|
- nvidia,enable-hibern8-war : Flag to enable hibernate war.
|
|
when enabled, ufs tegra driver will enable a WAR to reset Mphy.
|
|
- nvidia,max-hs-gear : Flag to set Max UFS HS Gear. Values are defined as below.
|
|
UFS_HS_G1 = <1>;
|
|
UFS_HS_G2 = <2>;
|
|
UFS_HS_G3 = <3>;
|
|
- nvidia,max-pwm-gear : Flag to set Max UFS PWM Gear. Values are defined as below.
|
|
UFS_PWM_G1 = <1>;
|
|
UFS_PWM_G2 = <2>;
|
|
UFS_PWM_G3 = <3>;
|
|
UFS_PWM_G4 = <4>;
|
|
UFS_PWM_G5 = <5>;
|
|
UFS_PWM_G6 = <6>;
|
|
UFS_PWM_G7 = <7>;
|
|
|
|
Note: If above properties are not defined it can be assumed that the supply
|
|
regulators or clocks are always on.
|
|
|
|
Example:
|
|
ufshc@0xfc598000 {
|
|
compatible = "jedec,ufs-1.1";
|
|
reg = <0xfc598000 0x800>;
|
|
interrupts = <0 28 0>;
|
|
|
|
clocks = <&core 0>, <&ref 0>, <&iface 0>;
|
|
clock-names = "core_clk", "ref_clk", "iface_clk";
|
|
freq-table-hz = <100000000 200000000>, <0 0>, <0 0>;
|
|
nvidia,enable-x2-config;
|
|
nvidia,enable-rx-calib;
|
|
nvidia,enable-hs-mode;
|
|
nvidia,mask-fast-auto-mode;
|
|
nvidia,max-hs-gear = <3>;
|
|
nvidia,max-pwm-gear = <4>;
|
|
};
|