forked from Archive/PX4-Autopilot
76 lines
3.4 KiB
Plaintext
76 lines
3.4 KiB
Plaintext
# If you change the order, add or remove arming_state_t states make sure to update the arrays
|
|
# in state_machine_helper.cpp as well.
|
|
uint8 ARMING_STATE_INIT = 0
|
|
uint8 ARMING_STATE_STANDBY = 1
|
|
uint8 ARMING_STATE_ARMED = 2
|
|
uint8 ARMING_STATE_ARMED_ERROR = 3
|
|
uint8 ARMING_STATE_STANDBY_ERROR = 4
|
|
uint8 ARMING_STATE_REBOOT = 5
|
|
uint8 ARMING_STATE_IN_AIR_RESTORE = 6
|
|
uint8 ARMING_STATE_MAX = 7
|
|
|
|
uint8 HIL_STATE_OFF = 0
|
|
uint8 HIL_STATE_ON = 1
|
|
|
|
# Navigation state, i.e. "what should vehicle do".
|
|
uint8 NAVIGATION_STATE_MANUAL = 0 # Manual mode
|
|
uint8 NAVIGATION_STATE_ALTCTL = 1 # Altitude control mode
|
|
uint8 NAVIGATION_STATE_POSCTL = 2 # Position control mode
|
|
uint8 NAVIGATION_STATE_AUTO_MISSION = 3 # Auto mission mode
|
|
uint8 NAVIGATION_STATE_AUTO_LOITER = 4 # Auto loiter mode
|
|
uint8 NAVIGATION_STATE_AUTO_RTL = 5 # Auto return to launch mode
|
|
uint8 NAVIGATION_STATE_AUTO_RCRECOVER = 6 # RC recover mode
|
|
uint8 NAVIGATION_STATE_AUTO_RTGS = 7 # Auto return to groundstation on data link loss
|
|
uint8 NAVIGATION_STATE_AUTO_LANDENGFAIL = 8 # Auto land on engine failure
|
|
uint8 NAVIGATION_STATE_AUTO_LANDGPSFAIL = 9 # Auto land on gps failure (e.g. open loop loiter down)
|
|
uint8 NAVIGATION_STATE_ACRO = 10 # Acro mode
|
|
uint8 NAVIGATION_STATE_UNUSED = 11 # Free slot
|
|
uint8 NAVIGATION_STATE_DESCEND = 12 # Descend mode (no position control)
|
|
uint8 NAVIGATION_STATE_TERMINATION = 13 # Termination mode
|
|
uint8 NAVIGATION_STATE_OFFBOARD = 14
|
|
uint8 NAVIGATION_STATE_STAB = 15 # Stabilized mode
|
|
uint8 NAVIGATION_STATE_RATTITUDE = 16 # Rattitude (aka "flip") mode
|
|
uint8 NAVIGATION_STATE_AUTO_TAKEOFF = 17 # Takeoff
|
|
uint8 NAVIGATION_STATE_AUTO_LAND = 18 # Land
|
|
uint8 NAVIGATION_STATE_AUTO_FOLLOW_TARGET = 19 # Auto Follow
|
|
uint8 NAVIGATION_STATE_MAX = 20
|
|
|
|
uint8 RC_IN_MODE_DEFAULT = 0
|
|
uint8 RC_IN_MODE_OFF = 1
|
|
uint8 RC_IN_MODE_GENERATED = 2
|
|
|
|
# state machine / state of vehicle.
|
|
# Encodes the complete system state and is set by the commander app.
|
|
uint64 timestamp # in microseconds since system start, is set whenever the writing thread stores new data
|
|
|
|
uint8 nav_state # set navigation state machine to specified value
|
|
uint8 arming_state # current arming state
|
|
uint8 hil_state # current hil state
|
|
bool failsafe # true if system is in failsafe state
|
|
|
|
uint8 system_type # system type, contains mavlink MAV_TYPE
|
|
uint32 system_id # system id, contains MAVLink's system ID field
|
|
uint32 component_id # subsystem / component id, contains MAVLink's component ID field
|
|
|
|
bool is_rotary_wing # True if system is in rotary wing configuration, so for a VTOL this is only true while flying as a multicopter
|
|
bool is_vtol # True if the system is VTOL capable
|
|
bool vtol_fw_permanent_stab # True if vtol should stabilize attitude for fw in manual mode
|
|
bool in_transition_mode # True if VTOL is doing a transition
|
|
|
|
bool rc_signal_lost # true if RC reception lost
|
|
uint8 rc_input_mode # set to 1 to disable the RC input, 2 to enable manual control to RC in mapping.
|
|
|
|
bool data_link_lost # datalink to GCS lost
|
|
uint8 data_link_lost_counter # counts unique data link lost events
|
|
bool engine_failure # Set to true if an engine failure is detected
|
|
bool engine_failure_cmd # Set to true if an engine failure mode is commanded
|
|
bool mission_failure # Set to true if mission could not continue/finish
|
|
|
|
# see SYS_STATUS mavlink message for the following
|
|
uint32 onboard_control_sensors_present
|
|
uint32 onboard_control_sensors_enabled
|
|
uint32 onboard_control_sensors_health
|
|
|
|
float32 load # processor load from 0 to 1
|
|
|