forked from Archive/PX4-Autopilot
375 lines
13 KiB
Plaintext
Executable File
375 lines
13 KiB
Plaintext
Executable File
README
|
||
^^^^^^
|
||
|
||
This README discusses issues unique to NuttX configurations for the
|
||
Freescale DEMO9S12NE64 development board.
|
||
|
||
CONTENTS
|
||
^^^^^^^^
|
||
• MC9S12NE64 Features
|
||
• Development Environment
|
||
• NuttX Buildroot Toolchain
|
||
• FreeScale HCS12 Serial Monitor
|
||
• Soft Registers
|
||
• HCS12/DEMO9S12NEC64-specific Configuration Options
|
||
• Configurations
|
||
|
||
MC9S12NE64 Features
|
||
^^^^^^^^^^^^^^^^^^^
|
||
|
||
• 16-bit HCS12 core
|
||
- HCS12 CPU
|
||
- Upward compatible with M68HC11 instruction set
|
||
- Interrupt stacking and programmer’s model identical to M68HC11
|
||
- Instruction queue
|
||
- Enhanced indexed addressing
|
||
- Memory map and interface (MMC)
|
||
- Interrupt control (INT)
|
||
- Background debug mode (BDM)
|
||
- Enhanced debug12 module, including breakpoints and change-of-flow
|
||
trace buffer (DBG)
|
||
- Multiplexed expansion bus interface (MEBI) - available only in
|
||
112-pin package version
|
||
• Wakeup interrupt inputs
|
||
- Up to 21 port bits available for wakeup interrupt function with
|
||
digital filtering
|
||
• Memory
|
||
- 64K bytes of FLASH EEPROM
|
||
- 8K bytes of RAM
|
||
• Analog-to-digital converter (ATD)
|
||
- One 8-channel module with 10-bit resolution
|
||
- External conversion trigger capability
|
||
• Timer module (TIM)
|
||
- 4-channel timer
|
||
- Each channel configurable as either input capture or output
|
||
compare
|
||
- Simple PWM mode
|
||
- Modulo reset of timer counter
|
||
- 16-bit pulse accumulator
|
||
- External event counting
|
||
- Gated time accumulation
|
||
• Serial interfaces
|
||
- Two asynchronous serial communications interface (SCI)
|
||
- One synchronous serial peripheral interface (SPI)
|
||
- One inter-IC bus (IIC)
|
||
• Ethernet Media access controller (EMAC)
|
||
- IEEE 802.3 compliant
|
||
- Medium-independent interface (MII)
|
||
- Full-duplex and half-duplex modes
|
||
- Flow control using pause frames
|
||
- MII management function
|
||
- Address recognition
|
||
- Frames with broadcast address are always accepted or always
|
||
rejected
|
||
- Exact match for single 48-bit individual (unicast) address
|
||
- Hash (64-bit hash) check of group (multicast) addresses
|
||
- Promiscuous mode
|
||
• Ethertype filter
|
||
• Loopback mode
|
||
• Two receive and one transmit Ethernet buffer interfaces
|
||
• Ethernet 10/100 Mbps transceiver (EPHY)
|
||
- IEEE 802.3 compliant
|
||
- Digital adaptive equalization
|
||
- Half-duplex and full-duplex
|
||
- Auto-negotiation next page ability
|
||
- Baseline wander (BLW) correction
|
||
- 125-MHz clock generator and timing recovery
|
||
- Integrated wave-shaping circuitry
|
||
- Loopback modes
|
||
• CRG (clock and reset generator module)
|
||
- Windowed COP watchdog
|
||
- Real-time interrupt
|
||
- Clock monitor
|
||
- Pierce oscillator
|
||
- Phase-locked loop clock frequency multiplier
|
||
- Limp home mode in absence of external clock
|
||
- 25-MHz crystal oscillator reference clock
|
||
• Operating frequency
|
||
- 50 MHz equivalent to 25 MHz bus speed for single chip
|
||
- 32 MHz equivalent to 16 MHz bus speed in expanded bus modes
|
||
• Internal 2.5-V regulator
|
||
- Supports an input voltage range from 3.3 V ± 5%
|
||
- Low-power mode capability
|
||
- Includes low-voltage reset (LVR) circuitry
|
||
• 80-pin TQFP-EP or 112-pin LQFP package
|
||
- Up to 70 I/O pins with 3.3 V input and drive capability (112-pin
|
||
package)
|
||
- Up to two dedicated 3.3 V input only lines (IRQ, XIRQ)
|
||
• Development support
|
||
- Single-wire background debug™ mode (BDM)
|
||
- On-chip hardware breakpoints
|
||
- Enhanced DBG debug features
|
||
|
||
Development Environment
|
||
^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
Either Linux or Cygwin on Windows can be used for the development
|
||
environment. The source has been built only using the GNU toolchain
|
||
(see below). Other toolchains will likely cause problems.
|
||
|
||
NuttX Buildroot Toolchain
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
||
be modified to point to the correct path to the HC12 GCC toolchain (if
|
||
different from the default in your PATH variable).
|
||
|
||
If you have no HC12 toolchain, one can be downloaded from the NuttX
|
||
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
|
||
This GNU toolchain builds and executes in the Linux or Cygwin
|
||
environments.
|
||
|
||
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
||
|
||
cd tools
|
||
./configure.sh demo9s12nec64/<sub-dir>
|
||
|
||
2. Download the latest buildroot package into <some-dir>
|
||
|
||
3. unpack the buildroot tarball. The resulting directory may
|
||
have versioning information on it like buildroot-x.y.z. If so,
|
||
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
||
|
||
4. cd <some-dir>/buildroot
|
||
|
||
5. cp configs/m9s12x-defconfig-3.3.6 .config
|
||
|
||
6. make oldconfig
|
||
|
||
7. make
|
||
|
||
If the make fails because it can't find the file to download, you may
|
||
have to locate the file on the internet and download it into the archives/
|
||
directory manually. For example, binutils-2.18 can be found here:
|
||
http://ftp.gnu.org/gnu/binutils/
|
||
|
||
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
||
the path to the newly built binaries.
|
||
|
||
See the file configs/README.txt in the buildroot source tree. That has more
|
||
detailed PLUS some special instructions that you will need to follow if you are
|
||
building a Cortex-M3 toolchain for Cygwin under Windows.
|
||
|
||
FreeScale HCS12 Serial Monitor
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
General:
|
||
The NuttX HCS12 port is configured to use the Freescale HCS serial
|
||
monitor. This monitor supports primitive debug commands that allow
|
||
FLASH/EEPROM programming and debugging through an RS-232 serial
|
||
interface. The serial monior is 2Kb in size and resides in FLASH at
|
||
addresses 0xf800-0xffff. The monitor does not use any RAM other than
|
||
the stack itself.
|
||
|
||
AN2458
|
||
The serial monitor is described in detail in Freescale Application
|
||
Note AN2458.pdf.
|
||
|
||
COP:
|
||
The serial monitor uses the COP for the cold reset function and should
|
||
not be used by the application without some precautions (see AN2458).
|
||
|
||
Clocking:
|
||
The serial monitor sets the operating frequency to 24 MHz. This is
|
||
not altered by the NuttX start-up; doing so would interfere with the
|
||
operation of the serial monitor.
|
||
|
||
Memory Configuration:
|
||
Registers:
|
||
• Register space is located at 0x0000–0x03ff.
|
||
FLASH:
|
||
• FLASH memory is any address greater than 0x4000. All paged
|
||
addresses are assumed to be FLASH memory.
|
||
• Application code should exclude the 0xf780–0xff7f memory.
|
||
SRAM:
|
||
• RAM ends at 0x3FFF and builds down to the limit of the device’s
|
||
available RAM.
|
||
• The serial monitor's stack pointer is set to the end of RAM+1
|
||
(0x4000).
|
||
EEPROM:
|
||
• EEPROM (if the target device has any) is limited to the available
|
||
space between the registers and the RAM (0x0400–to start of RAM).
|
||
External Devices:
|
||
• External devices attached to the multiplexed external bus
|
||
interface are not supported
|
||
|
||
Serial Communications:
|
||
The serial monitor uses RS-232 serial communications through SCI0 at
|
||
115,200 baud. The monitor must have exclusive use of this interface.
|
||
Access to the serial port is available through a monitor jump table.
|
||
|
||
Interrrupts:
|
||
The serial monitor redirects interrupt vectors to an unprotected
|
||
portion of FLASH just before the protected monitor program
|
||
(0xf780–0xf7fe). The monitor will automatically redirect vector
|
||
programming operations to these user vectors. The user code should
|
||
therefore keep the normal (non-monitor) vector locations
|
||
(0xff80–0xfffe).
|
||
|
||
Soft Registers
|
||
^^^^^^^^^^^^^^
|
||
|
||
The mc68hcs12 compilation is prone to errors like the following:
|
||
|
||
CC: lib_b16sin.c
|
||
lib_b16sin.c: In function `b16sin':
|
||
lib_b16sin.c:110: error: unable to find a register to spill in class `S_REGS'
|
||
lib_b16sin.c:110: error: this is the insn:
|
||
(insn:HI 41 46 44 8 (parallel [
|
||
(set (subreg:SI (reg:DI 58 [ rad ]) 4)
|
||
(reg/v:SI 54 [ rad ]))
|
||
(clobber (scratch:HI))
|
||
]) 20 {movsi_internal} (insn_list 46 (nil))
|
||
(expr_list:REG_UNUSED (scratch:HI)
|
||
(expr_list:REG_NO_CONFLICT (reg/v:SI 54 [ rad ])
|
||
(nil))))
|
||
lib_b16sin.c:110: confused by earlier errors, bailing out
|
||
|
||
There are several ways that this error could be fixed:
|
||
|
||
1. Increase the number of soft registers (i.e., "fake" registers defined
|
||
at fixed memory locations). This can be done by adding something like
|
||
-msoft-reg-count=4 to the CFLAGS. This approach was not taken
|
||
because:
|
||
|
||
- This slows hcs12 performance
|
||
- All of these soft registers wouil have to be saved and restored
|
||
on every interrupt and context switch.
|
||
|
||
2. Lowering the optimization level by dropping -Os to -O2 or, more likely,
|
||
by removing -fomit-frame-pointer. Also not desireable becauase 99% of the
|
||
files that do not have this problem also increase in size. Special case
|
||
compilation with reduced optimization levels just for the files that need
|
||
it could be done, but this would complicate the make system.
|
||
|
||
3. Restructuring files to reduce the complexity. If you add local variables
|
||
to hold intermediate computational results, this error can be eliminated.
|
||
This is the approach taken in NuttX. It has disadvantages only in that
|
||
(1) it takes some effort and good guessing to eliminate the problem, and (2)
|
||
the problem is not really eliminated -- it can and will re-occur when files
|
||
are changed or new files are added.
|
||
|
||
4. Many files are built that are needed by DEM09S12NE64. Another very simple
|
||
option if those problem files are needed is to just remove the offending
|
||
files from the Make.defs file so that they no longer cause a problem.
|
||
|
||
HCS12/DEMO9S12NEC64-specific Configuration Options
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
||
be set to:
|
||
|
||
CONFIG_ARCH=hc
|
||
|
||
CONFIG_ARCH_family - For use in C code:
|
||
|
||
CONFIG_ARCH_HC=y
|
||
|
||
CONFIG_ARCH_architecture - For use in C code:
|
||
|
||
CONFIG_ARCH_HCS12=y
|
||
|
||
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||
|
||
CONFIG_ARCH_CHIP=mc92s12nec64
|
||
|
||
CONFIG_ARCH_CHIP_name - For use in C code
|
||
|
||
CONFIG_ARCH_CHIP_MCS92S12NEC64
|
||
|
||
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
||
hence, the board that supports the particular chip or SoC.
|
||
|
||
CONFIG_ARCH_BOARD=demo9s12nec64
|
||
|
||
CONFIG_ARCH_BOARD_name - For use in C code
|
||
|
||
CONFIG_ARCH_BOARD_DEMOS92S12NEC64 (for the Freescale DEMO9S12NE64 development board)
|
||
|
||
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
||
of delay loops
|
||
|
||
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
||
endian)
|
||
|
||
CONFIG_DRAM_SIZE - Describes the installed RAM.
|
||
|
||
CONFIG_DRAM_START - The start address of installed RAM
|
||
|
||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
||
have LEDs
|
||
|
||
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||
stack. If defined, this symbol is the size of the interrupt
|
||
stack in bytes. If not defined, the user task stacks will be
|
||
used during interrupt handling.
|
||
|
||
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||
|
||
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||
cause a 100 second delay during boot-up. This 100 second delay
|
||
serves no purpose other than it allows you to calibratre
|
||
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
||
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
||
the delay actually is 100 seconds.
|
||
|
||
GPIO Interrupts
|
||
|
||
CONFIG_GPIO_IRQ - Enable general support for GPIO IRQs
|
||
CONFIG_HCS12_PORTG_INTS - Enable PortG IRQs
|
||
CONFIG_HCS12_PORTH_INTS - Enable PortH IRQs
|
||
CONFIG_HCS12_PORTJ_INTS - Enable PortJ IRQs
|
||
|
||
HCS12 build options:
|
||
|
||
CONFIG_HCS12_SERIALMON - Indicates that the target systems uses
|
||
the Freescale serial bootloader.
|
||
|
||
CONFIG_HCS12_NONBANKED - Indicates that the target systems does not
|
||
support banking. Only short calls are made; one fixed page is
|
||
presented the the paging window. Only 48Kb of FLASH is usable
|
||
in this configuration: pages 3e, 3d, then 3f will appear as a
|
||
contiguous address space in memory.
|
||
|
||
HCS12 Sub-system support
|
||
|
||
CONFIG_HCS12_SCI0
|
||
CONFIG_HCS12_SCI1
|
||
|
||
HCS12 specific device driver settings:
|
||
|
||
CONFIG_SCIn_SERIAL_CONSOLE - selects SCIn for the console and ttys0
|
||
(default is the SCI0).
|
||
|
||
CONFIG_SCIn_RXBUFSIZE - Characters are buffered as received.
|
||
This specific the size of the receive buffer
|
||
|
||
CONFIG_SCIn_TXBUFSIZE - Characters are buffered before
|
||
being sent. This specific the size of the transmit buffer
|
||
|
||
CONFIG_SCIn_BAUD - The configure BAUD of the UART.
|
||
|
||
CONFIG_SCIn_BITS - The number of bits. Must be either 7 or 8.
|
||
|
||
CONFIG_SCIn_PARTIY - 0=no parity, 1=odd parity, 2=even parity, 3=mark 1, 4=space 0
|
||
|
||
CONFIG_SCIn_2STOP - Two stop bits
|
||
|
||
Configurations
|
||
^^^^^^^^^^^^^^
|
||
|
||
Each Freescale HCS12 configuration is maintained in a sudirectory and
|
||
can be selected as follow:
|
||
|
||
cd tools
|
||
./configure.sh demo9s12nec64/<subdir>
|
||
cd -
|
||
. ./setenv.sh
|
||
|
||
Where <subdir> is one of the following:
|
||
|
||
ostest:
|
||
This configuration directory, performs a simple OS test using
|
||
examples/ostest.
|
||
|