px4-firmware/apps/px4io/adc.c

168 lines
4.7 KiB
C

/****************************************************************************
*
* Copyright (C) 2012 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name PX4 nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/**
* @file adc.c
*
* Simple ADC support for PX4IO on STM32.
*/
#include <nuttx/config.h>
#include <stdint.h>
#include <nuttx/arch.h>
#include <arch/stm32/chip.h>
#include <stm32_internal.h>
#include <drivers/drv_hrt.h>
#include <systemlib/perf_counter.h>
#define DEBUG
#include "px4io.h"
/*
* Register accessors.
* For now, no reason not to just use ADC1.
*/
#define REG(_reg) (*(volatile uint32_t *)(STM32_ADC1_BASE + _reg))
#define rSR REG(STM32_ADC_SR_OFFSET)
#define rCR1 REG(STM32_ADC_CR1_OFFSET)
#define rCR2 REG(STM32_ADC_CR2_OFFSET)
#define rSMPR1 REG(STM32_ADC_SMPR1_OFFSET)
#define rSMPR2 REG(STM32_ADC_SMPR2_OFFSET)
#define rJOFR1 REG(STM32_ADC_JOFR1_OFFSET)
#define rJOFR2 REG(STM32_ADC_JOFR2_OFFSET)
#define rJOFR3 REG(STM32_ADC_JOFR3_OFFSET)
#define rJOFR4 REG(STM32_ADC_JOFR4_OFFSET)
#define rHTR REG(STM32_ADC_HTR_OFFSET)
#define rLTR REG(STM32_ADC_LTR_OFFSET)
#define rSQR1 REG(STM32_ADC_SQR1_OFFSET)
#define rSQR2 REG(STM32_ADC_SQR2_OFFSET)
#define rSQR3 REG(STM32_ADC_SQR3_OFFSET)
#define rJSQR REG(STM32_ADC_JSQR_OFFSET)
#define rJDR1 REG(STM32_ADC_JDR1_OFFSET)
#define rJDR2 REG(STM32_ADC_JDR2_OFFSET)
#define rJDR3 REG(STM32_ADC_JDR3_OFFSET)
#define rJDR4 REG(STM32_ADC_JDR4_OFFSET)
#define rDR REG(STM32_ADC_DR_OFFSET)
perf_counter_t adc_perf;
int
adc_init(void)
{
adc_perf = perf_alloc(PC_ELAPSED, "adc");
/* do calibration if supported */
#ifdef ADC_CR2_CAL
rCR2 |= ADC_CR2_RSTCAL;
up_udelay(1);
if (rCR2 & ADC_CR2_RSTCAL)
return -1;
rCR2 |= ADC_CR2_CAL;
up_udelay(100);
if (rCR2 & ADC_CR2_CAL)
return -1;
#endif
/* arbitrarily configure all channels for 55 cycle sample time */
rSMPR1 = 0b00000011011011011011011011011011;
rSMPR2 = 0b00011011011011011011011011011011;
/* XXX for F2/4, might want to select 12-bit mode? */
rCR1 = 0;
/* enable the temperature sensor / Vrefint channel if supported*/
rCR2 =
#ifdef ADC_CR2_TSVREFE
/* enable the temperature sensor in CR2 */
ADC_CR2_TSVREFE |
#endif
0;
#ifdef ADC_CCR_TSVREFE
/* enable temperature sensor in CCR */
rCCR = ADC_CCR_TSVREFE;
#endif
/* configure for a single-channel sequence */
rSQR1 = 0;
rSQR2 = 0;
rSQR3 = 0; /* will be updated with the channel each tick */
/* power-cycle the ADC and turn it on */
rCR2 &= ~ADC_CR2_ADON;
up_udelay(10);
rCR2 |= ADC_CR2_ADON;
up_udelay(10);
rCR2 |= ADC_CR2_ADON;
up_udelay(10);
return 0;
}
uint16_t
adc_measure(unsigned channel)
{
perf_begin(adc_perf);
/* clear any previous EOC */
if (rSR & ADC_SR_EOC)
rSR &= ~ADC_SR_EOC;
/* run a single conversion right now - should take about 60 cycles (a few microseconds) max */
rSQR3 = channel;
rCR2 |= ADC_CR2_ADON;
/* wait for the conversion to complete */
hrt_abstime now = hrt_absolute_time();
while (!(rSR & ADC_SR_EOC)) {
/* never spin forever - this will give a bogus result though */
if ((hrt_absolute_time() - now) > 1000) {
debug("adc timeout");
break;
}
}
/* read the result and clear EOC */
uint16_t result = rDR;
perf_end(adc_perf);
return result;
}