dark0707
/
px4-firmware
forked from Archive/PX4-Autopilot
1
0
Fork 0
Code Pull Requests Activity
px4-firmware/nuttx/configs/stm3210e-eval/include/board.h

324 lines
12 KiB
C
Raw Blame History

/************************************************************************************
* configs/stm3210e-eval/include/board.h
* include/arch/board/board.h
*
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __ARCH_BOARD_BOARD_H
#define __ARCH_BOARD_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
#include "stm32_rcc.h"
#include "stm32_sdio.h"
#include "stm32_internal.h"
/************************************************************************************
* Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* On-board crystal frequency is 8MHz (HSE) */
#define STM32_BOARD_XTAL 8000000ul
/* PLL source is HSE/1, PLL multipler is 9: PLL frequency is 8MHz (XTAL) x 9 = 72MHz */
#define STM32_CFGR_PLLSRC RCC_CFGR_PLLSRC
#define STM32_CFGR_PLLXTPRE 0
#define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx9
#define STM32_PLL_FREQUENCY (9*STM32_BOARD_XTAL)
/* Use the PLL and set the SYSCLK source to be the PLL */
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
#define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY
/* AHB clock (HCLK) is SYSCLK (72MHz) */
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK
#define STM32_HCLK_FREQUENCY STM32_PLL_FREQUENCY
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */
/* APB2 clock (PCLK2) is HCLK (72MHz) */
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK
#define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY
#define STM32_APB2_CLKIN (STM32_PCLK2_FREQUENCY) /* Timers 2-7, 12-14 */
/* APB2 timers 1 and 8 will receive PCLK2. */
#define STM32_APB2_TIM1_CLKIN (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM8_CLKIN (STM32_PCLK2_FREQUENCY)
/* APB1 clock (PCLK1) is HCLK/2 (36MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2)
/* APB1 timers 2-4 will be twice PCLK1 (I presume the remaining will receive PCLK1) */
#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM5_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM7_CLKIN (STM32_PCLK1_FREQUENCY)
/* USB divider -- Divide PLL clock by 1.5 */
#define STM32_CFGR_USBPRE 0
/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
* otherwise frequency is 2xAPBx.
* Note: TIM1,8 are on APB2, others on APB1 */
#define STM32_TIM18_FREQUENCY STM32_HCLK_FREQUENCY
#define STM32_TIM27_FREQUENCY STM32_HCLK_FREQUENCY
/* SDIO dividers. Note that slower clocking is required when DMA is disabled
* in order to avoid RX overrun/TX underrun errors due to delayed responses
* to service FIFOs in interrupt driven mode. These values have not been
* tuned!!!
*
* HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz
*/
#define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT)
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# define SDIO_MMCXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
#endif
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
#endif
/* SRAM definitions *****************************************************************/
/* The 8 Mbit SRAM is provided on the PT3 board using the FSMC_NE3 chip select. */
/* This is the Bank1 SRAM3 address: */
#define BOARD_SRAM_BASE 0x68000000 /* Bank2 SRAM3 base address */
#define BOARD_SRAM_SIZE (1*1024*1024) /* 8-Mbit = 1-Mbyte */
/* LED definitions ******************************************************************/
/* The STM3210E-EVAL board has 4 LEDs that we will encode as: */
#define LED_STARTED 0 /* LED1 */
#define LED_HEAPALLOCATE 1 /* LED2 */
#define LED_IRQSENABLED 2 /* LED1 + LED2 */
#define LED_STACKCREATED 3 /* LED3 */
#define LED_INIRQ 4 /* LED1 + LED3 */
#define LED_SIGNAL 5 /* LED2 + LED3 */
#define LED_ASSERTION 6 /* LED1 + LED2 + LED3 */
#define LED_PANIC 7 /* N/C + N/C + N/C + LED4 */
/* The STM3210E-EVAL supports several buttons
*
* Reset -- Connected to NRST
* Wakeup -- Connected to PA.0
* Tamper -- Connected to PC.13
* Key -- Connected to PG.8
*
* And a Joystick
*
* Joystick center -- Connected to PG.7
* Joystick down -- Connected to PD.3
* Joystick left -- Connected to PG.14
* Joystick right -- Connected to PG.13
* Joystick up -- Connected to PG.15
*/
#define BUTTON_WAKEUP 0
#define BUTTON_TAMPER 1
#define BUTTON_KEY 2
#define JOYSTICK_SEL 3
#define JOYSTICK_DOWN 4
#define JOYSTICK_LEFT 5
#define JOYSTICK_RIGHT 6
#define JOYSTICK_UP 7
#define NUM_BUTTONS 8
#define BUTTON_WAKEUP_BIT (1 << BUTTON_WAKEUP)
#define BUTTON_TAMPER_BIT (1 << BUTTON_TAMPER)
#define BUTTON_KEY_BIT (1 << BUTTON_KEY)
#define JOYSTICK_SEL_BIT (1 << JOYSTICK_SEL)
#define JOYSTICK_DOWN_BIT (1 << JOYSTICK_DOWN)
#define JOYSTICK_LEFT_BIT (1 << JOYSTICK_LEFT)
#define JOYSTICK_RIGHT_BIT (1 << JOYSTICK_RIGHT)
#define JOYSTICK_UP_BIT (1 << JOYSTICK_UP)
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
EXTERN void stm32_boardinitialize(void);
/************************************************************************************
* Button support.
*
* Description:
* up_buttoninit() must be called to initialize button resources. After
* that, up_buttons() may be called to collect the current state of all
* buttons or up_irqbutton() may be called to register button interrupt
* handlers.
*
* After up_buttoninit() has been called, up_buttons() may be called to
* collect the state of all buttons. up_buttons() returns an 8-bit bit set
* with each bit associated with a button. See the BUTTON_*_BIT and JOYSTICK_*_BIT
* definitions in board.h for the meaning of each bit.
*
* up_irqbutton() may be called to register an interrupt handler that will
* be called when a button is depressed or released. The ID value is a
* button enumeration value that uniquely identifies a button resource. See the
* BUTTON_* and JOYSTICK_* definitions in board.h for the meaning of enumeration
* value. The previous interrupt handler address is returned (so that it may
* restored, if so desired).
*
************************************************************************************/
#ifdef CONFIG_ARCH_BUTTONS
EXTERN void up_buttoninit(void);
EXTERN uint8_t up_buttons(void);
#ifdef CONFIG_ARCH_IRQBUTTONS
EXTERN xcpt_t up_irqbutton(int id, xcpt_t irqhandler);
#endif
#endif
/************************************************************************************
* Name: stm3210e_lcdclear
*
* Description:
* This is a non-standard LCD interface just for the STM3210E-EVAL board. Because
* of the various rotations, clearing the display in the normal way by writing a
* sequences of runs that covers the entire display can be very slow. Here the
* dispaly is cleared by simply setting all GRAM memory to the specified color.
*
************************************************************************************/
#ifdef CONFIG_STM32_FSMC
EXTERN void stm3210e_lcdclear(uint16_t color);
#endif
/************************************************************************************
* Name: stm32_lm75initialize
*
* Description:
* Initialize and register the LM-75 Temperature Sensor driver.
*
* Input parameters:
* devpath - The full path to the driver to register. E.g., "/dev/temp0"
*
* Returned Value:
* Zero (OK) on success; a negated errno value on failure.
*
************************************************************************************/
#if defined(CONFIG_I2C) && defined(CONFIG_I2C_LM75) && defined(CONFIG_STM32_I2C1)
EXTERN int stm32_lm75initialize(FAR const char *devpath);
#endif
/************************************************************************************
* Name: stm32_lm75attach
*
* Description:
* Attach the LM-75 interrupt handler
*
* Input parameters:
* irqhandler - the LM-75 interrupt handler
*
* Returned Value:
* The previous LM-75 interrupt handler
*
************************************************************************************/
#if defined(CONFIG_I2C) && defined(CONFIG_I2C_LM75) && defined(CONFIG_STM32_I2C1)
EXTERN xcpt_t stm32_lm75attach(xcpt_t irqhandler);
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_BOARD_BOARD_H */
View Git Blame Copy Permalink